Öz
Improvement of high power and high performance applications causes attention to the DC-DC converter topologies. In this paper we analyze and simulate full-bridge boost converter, an isolated DC-DC converter. The advantages of isolated DC-DC converters include high efficiency, low manufacturing cost, safety, electrical isolation using transformer. The transformer is used to produce a higher voltage in secondary voltage side. Matlab Simulink is used for simulation of this converter. Nominal input voltage in this simulation is 30V and the output voltage is 55V. Also other parameters are given in this paper.
Kaynakça
- R. Erickson and D. Maksimović, Fundamentals of power electronics. Norwell, Mass.: Kluwer Academic, 2001.
- D. Choi, B. Lee, S. Choi, C. Won and D. Yoo, 'A novel power conversion circuit for cost-effective battery-fuel cell hybrid systems', Journal of Power Sources, vol. 152, pp. 245-255, 2005.
- S. Moon, “Multiphase Isolated DC-DC Converters for Low-Voltage High-Power Fuel Cell Applications”, M.S. thesis, Virginia Polytechnic Institute and State University, 2007.
- D. D. Gaikwad and M. S Chavan, “Implementation of DC-DC Converter for MPPT by Direct Control Method”, International Journal of Engineering Research & Technology, Vol. 3(9), pp. 1-5, 2014.
- Anupama V C, Surumi Hussaisar, Jinan O.K and Balaji P, “Design and Development of a 66.46W Multi-output Soft Switching Active Clamp Fly-back Converter Power Supply”, International Journal of Advanced Information Science and Technology, Vol.30 (30), pp. 1-6, 2014.
- M. Baei, M. Narimani and G. Moschopoulos, Journal of Power Electronics, vol. 14, no. 2, pp. 237-248, 2014.
Öz
Improvement of high power and high performance applications causes attention to the DC-DC converter topologies. In this paper we analyze and simulate full-bridge boost converter, an isolated DC-DC converter. The advantages of isolated DC-DC converters include high efficiency, low manufacturing cost, safety, electrical isolation using transformer. The transformer is used to produce a higher voltage in secondary voltage side. Matlab Simulink is used for simulation of this converter. Nominal input voltage in this simulation is 30V and the output voltage is 55V. Also other parameters are given in this paper.
Kaynakça
- R. Erickson and D. Maksimović, Fundamentals of power electronics. Norwell, Mass.: Kluwer Academic, 2001.
- D. Choi, B. Lee, S. Choi, C. Won and D. Yoo, 'A novel power conversion circuit for cost-effective battery-fuel cell hybrid systems', Journal of Power Sources, vol. 152, pp. 245-255, 2005.
- S. Moon, “Multiphase Isolated DC-DC Converters for Low-Voltage High-Power Fuel Cell Applications”, M.S. thesis, Virginia Polytechnic Institute and State University, 2007.
- D. D. Gaikwad and M. S Chavan, “Implementation of DC-DC Converter for MPPT by Direct Control Method”, International Journal of Engineering Research & Technology, Vol. 3(9), pp. 1-5, 2014.
- Anupama V C, Surumi Hussaisar, Jinan O.K and Balaji P, “Design and Development of a 66.46W Multi-output Soft Switching Active Clamp Fly-back Converter Power Supply”, International Journal of Advanced Information Science and Technology, Vol.30 (30), pp. 1-6, 2014.
- M. Baei, M. Narimani and G. Moschopoulos, Journal of Power Electronics, vol. 14, no. 2, pp. 237-248, 2014.
Ayrıntılar
| Bölüm | Reviews |
|---|---|
| Yazarlar | |
| Yayımlanma Tarihi | 1 Eylül 2015 |
| Yayımlandığı Sayı | Yıl 2015 Cilt: 3 Sayı: 2 |
All articles published by BAJECE are licensed under the Creative Commons Attribution 4.0 International License. This permits anyone to copy, redistribute, remix, transmit and adapt the work provided the original work and source is appropriately cited.