Objective: This in vitro studies aim is the changes on the surface of the material will be observed and compared by using three different resin composites and two different bleaching agents which are commonly used nowadays.
Material and Methods: Bulk fill (BFK) Nanohybrid (NHK) and suprananohybrid resin (SNK) 30 samples of each composites which is 90 pieces of composite samples total. These samples will be produced with a diameter of 8mm and a height of 4mm. Then they will be randomly grouped into ten. First type of composite group will be applied office type whitening (OT), second type of composite group will be applied home type whitening (HT) and the last group will be the control group. Before and after applying whitening agents, the surface roughness will be measured, recorded and statiscally analysed with ANOVA test.
Results: HT application changed surface roughness significantly (p <0.05) and this difference was caused by SNK. The significant difference for OT and HT groups occured between BFK and NHK groups with SNK and for K group between SNK and other groups. (p <0.05)
Conclusion: As a result of this study, it has been found that bleaching agents will cause changes on the surface of the polished composite restorations. While the difference between the materials emerged only for the ET group, the surface roughness for the materials was affected by OT > ET > K respectively.
Amaç: Bu in vitro çalışmanın amacı günümüzde sıklıkla kullanılan 3 rezin kompozite iki farklı ağartma ajanı uygulanarak materyalin yüzeyinde meydana gelen değişimler yüzey pürüzlülüğü açısından incelenecek ve karşılaştırılacaktır.
Gereç ve Yöntemler: Bulk Fill (BFK), Nanohibrit (NHK) ve Suprananohibrit (SNK) kompozitlerin her birinden 30’ar adet olmak üzere, 90 adet kompozit örnek; 8mm çap ve 4mm kalınlıkta üretilecek, rastgele 10’arlı gruplara ayrılarak birisine ofis tipi ağartma ajanı (OT), diğerine ev tipi ağartma ajanı (ET) uygulanırken sonuncusu kontrol grubu olarak ayrılacaktır. Ağartma ajanları uygulamadan önce ve sonra profilometre ile yüzey pürüzlülüğü ölçümü yapılarak kaydedilecek ve ANOVA testi ile istatistiksel analizi yapılacaktır.
Bulgular: ET uygulaması yüzey pürüzlülüğünü anlamlı şekilde (p<0,05) değiştirmiş ve bu farklılık SNK’dan kaynaklanmıştır. BFK ve NHK için OT grubu ile diğerleri arasında, SNK için K grubu ile diğerleri arasındaki farklılık istatistiksel olarak anlamlı bulunmuştur (p<0,05).
Sonuç: Yapılan bu çalışmanın sonucunda ağartma ajanlarının polisajlanmış kompozit restorasyonların yüzeyinde değişimlere sebep olacağı bulunmuştur. Materyaller arasındaki farklılık sadece ET grup için ortaya çıkmışken materyaller için yüzey pürüzlülüğü sırasıyla OT>ET>K şeklinde etkilenmiştir.
Primary Language | Turkish |
---|---|
Subjects | Dentistry |
Journal Section | RESEARCH ARTICLE |
Authors | |
Publication Date | October 31, 2020 |
Submission Date | July 16, 2020 |
Acceptance Date | September 20, 2020 |
Published in Issue | Year 2020 Volume: 2 Issue: 2 |
Bu eser Creative Commons Atıf-GayriTicari 4.0 Uluslararası Lisansı ile lisanslanmıştır.