An analytical solution of bimetal rod extrusion process through conical dies

Yıl 2015, Cilt: 28 Sayı: 2, 301 - 310, 22.06.2015

Heshmatollah Haghighat H. Askar

Öz

In the present article,the radial and peripheral velocity components are determined for mono-metal rod extrusion through conical dies and then they are extended to extrusion process of initially bonded bimetal rods. By optimizing the total power with respect to the shape of the inlet shear boundary, the amount of extrusion force is obtained. The obtained solutions are tested with other ones found in the literature about this theme and with the results produced by the finite element method. It is found that all of the predicted results are in good agreement with the values computed by the finite element method and experimental results.

Anahtar Kelimeler

rod extrusion, velocity field, upper bound method

Kaynakça

• [1] Ahmed N. Extrusion of copper clad aluminum wire. J Mech Work Technol 1978;2:19–32.
• [2] Berski S, Dyja H, Banaszek G, Janik M. Theoretical analysis of bimetallic rod extrusion process in double reduction die. J Mater Process Technol 2004;153–154:583–8.
• [3] B. Avitzur, R.Wu, S. Talbert, Y.T.Chou, Criterion for the Prevention of Core Fracture During Extrusion of Bimetal Rods, Journal of Engineering for Industry, 1982, Vol. 104, pp. 293-304.
• [4] Osakada, K, Limb, M & Mellor, PB 1973, Hydrostatic extrusion of composite rods with hard cores, International Journal of Mechanical Sciences, vol. 15, pp. 291-307.
• [5] Tokuno, H & Ikeda, K 1991, Analysis of deformation in extrusion of composite rods, Journal of Materials Processing Technology, vol. 26, pp. 323-335.
• [6] Yang, DY, Kim, YG & Lee, CM 1991, An upperbound solution for axisymetric extrusion of composite rods through curved dies, International Journal of Mechanical Sciences, vol. 31, pp. 565- 575.
• [7] Sliwa, R 1997, Plastic zones in the extrusion of metal composites, Journal of Materials Processing Technology, vol. 67, pp. 29-35.
• [8] Chitkara, NR & Aleem, A 2001a, Extrusion of axisymmetric bi-metallic tubes from solid circular billets: application of a generalized upper bound analysis and some experiments, International Journal of Mechanical Sciences, vol. 43, pp. 2833- 2856.
• [9] Chitkara, NR & Aleem, A 2001b, Extrusion of axisymmetric bi-metallic tubes: some experiments using hollow billets and the application of a generalized slab method of analysis, International Journal of Mechanical Sciences, vol. 43, pp. 2857– 2882.
• [10] Kang, CG, Jung, YJ & Kwon, HC 2002, Finite element simulation of die design for hot extrusion process of Al/Cu clad composite and its experimental investigation, Journal of Materials Processing Technology, vol. 124, pp. 49-56.
• [11] Hwang, YM & Hwang, TF 2002, An investigation into the plastic deformation behavior within a conical die during composite rod extrusion, Journal of Materials Processing Technology, vol. 121, pp. 226-233.
• [12] Kazanowski, P, Epler, ME & Misiolek, WZ 2004, Bi-metal rod extrusion-process and product optimization, Materials Science and Engineering A, vol.369, pp. 170–180.
• [13] Nowotynska, I & Smykla, A 2009, Influence of die geometric parameters on plastic flow of Layer composites during extrusion process, Journal of Materials Processing Technology, vol. 209, pp. 1943-1949.
• [14] Khosravifard, A., Ebrahimi, R., Investigation of parameters affecting interface strength in Al/Cu clad bimetal rod extrusion process, Materials and Design vol. 31, pp. 493-499, (2010).
• [15] Haghighat, H, Asgari, GR 2011, A generalized spherical velocity field for bi-metallic tube extrusion through dies of any shape, International Journal of Mechanical Sciences, vol. 53, pp. 248- 253