ABRASION EFFECT OF FLOW ON PIPES

Yıl 2015, Cilt: 7 Sayı: 1, 9 - 24, 01.03.2015

M. Baduna Koçyiğit Ö. Koçyiğit A. Şafak

https://doi.org/10.24107/ijeas.251232

Öz

One of the main factors in determining pipe diameter to design of potable water supplying systems is the flow velocity. The design flow velocity cannot be chosen above a certain value since higher velocities cause deterioration of cement mortar lining, additional management costs and destructive water impact.The flow velocity limits noted in the literature are given in a specific range (0,5-3,0 m/sec). However, the mentioned velocity limits can be increased up to a certain value in systems without pumping by decreasing the pipe diameter. Better quality of cement mortar used in the interior lining of the pipes help to increase capacity and thus the cost of the project can be reduced. In this study, an experimental pipeline model was set up from ductile pipes with cement mortar lining in which high velocities were aimed and a series of experiments were conducted. Experimental set up was composed of ductile pipes with four different diameters (Ø200300-400-450 mm) and water was recycled from a reservoir to the pipe system and back to the reservoir by pumps. The measured thicknesses from the pipes were compared and the changes on the cement mortar lining were observed

Anahtar Kelimeler

Water pipeline, cement mortar lining, abrasion, flow velocity

Kaynakça

• [1] Fair, G.M. and Geyer, J.C. Su Getirme ve Kullanılmış Suların Uzaklaştırma Esasları, Çeviren: Muslu, Y., Türkiye: Matbaa Teknisyenleri Koll. Şti. İstanbul, 184-185, 1973.
• [2] Bay, M.E. İçmesuyu Proje El Kitabı, Türkiye: Teknik Yayınevi, 43, 2006. [3] Yanmaz, A.M., Applied Water Resources Engineering, Türkiye: ODTÜ Basım İşliği, 174, 1997.
• [4] İller Bankası, İçmesuyu Tesisleri Etüt, Fizibilite ve Projelerin Hazırlanmasına ait Teknik Şartname Türkiye, 25, 2013.
• [5] Kaisha, K. Ductile Iron Pipeline Design Manual, 2nd. Edition, Kubota Corporation/Japan, 32, 1992.
• [6] ASHRAE Handbook. Fundemantals Pipe Sizing, Chapter 33, 155-186, 1993.
• [7] Badr, H. M., Habib, M. A., Ben-Mansour, R. and Said, S. A. M., Numerical investigation of erosion threshold velocity in a pipe with sudden contraction, computers & fluids, 34(6), 721-742, 2005.
• [8] Ball, E.F. and Webster. C.J.D., Some measurements of water-flow noise in copper and ABS pipes with various flow velocities, The Building Services Engineer, 44 (2), 33, 1976.
• [9] Carrier, Piping design in system design manual, Carrier Air Conditioning Company, Syracuse, NY, 1960.
• [10] Crane Co., Flow of fluids through valves, fittings and pipe, Technical Paper No. 410, Crane Company, New York, 1976.
• [11] Rogers, W.L., Experimental approaches to the study of noise and noise transmission in piping systems, ASHRAE Transactions 59, 347-60, 1953.
• [12] Rogers, W.L., Sound-pressure levels and frequencies produced by flow of water through pipe and fittings, ASHRAE Transactions 60, 411-30, 1954.
• [13] Rogers, W.L., Noise production and damping in water piping, ASHRAE Transactions 62, 39, 1956.
• [14] Marseille, B., Noise transmission in piping, heating and ventilating engineering (June), 674, 1965.
• [15] Finnie, I., Some observations on the erosion of ductile metals, Wear, 19(1), 81-90, 1972
• [16] Blanchard, D.J., Griffith, P. and Rabinowicz, E., Erosion of a pipe bend by solid particle entrained in water, Journal of Engineering for Industry, (106), 213-217, 1984.
• [17] Finnie, I., The mechanism of erosion of ductile metals, Proceedings of 3rd US National Congress of Applied Mechanics, 527-532, 1958.
• [18]API RP 14E (American Petrolium Institute Recommended Practice for Design and Installation of Offshore Production [19] Schmitt, H.G. and Bakalli, M., Flow Assisted Corrosion, Elsevier, 979-980, 2010.
• [20] Bozzini, B., Ricotti, M.E., Boniardi, M. and Mele, C., Evaluation of erosion–corrosion in multiphase flow via CFD and experimental analysis, Wear, Elsevier 255, 237–245, 2003.
• [21] Hwang, N.H.C. and Houghtalen, R.J., Fundemantals of Hydraulic Engineering Systems, 3rd. Edition, Prentice Hall, London, 3, 1996.
• [22] Şafak, A., İç Cidarı Beton Kaplı Borularda Akımın Aşındırma Etkisi, Gazi Ünv. Fen Bilimleri Ens., Yüksek Lisans Tezi, 121 p., Ankara, 2014.
• [23] Munson, B.R., Young, D.F and Okiishi, T.H., Fundamentals of Fluid Mechanics, 2nd. Edition, 458 - 460, 1994.
• [24] AGAPOL, http://www.agakim.com.tr/, AGAKİM Kimya San. ve Tic. A.Ş., Adana, Turkey
• [25] Beer, F.P., Johnstan A.R., DeWolf J.T. and Mazurek D.F., Mechanics of Materials, 5. Edition, Mc. Graw Hill, 435-437, 2006.