Thermodynamic Justification for the Ni/Al/Ni Joint Formation by a Diffusion Brazing

Yıl 2011, Cilt: 14 Sayı: 3, 97 - 105, 25.07.2011

T. Okane C. Senderowski D. Zasada B. Kania J. Janczak-rusch Waldemar Wolczynski

Öz

A theoretical model for the joint formation was developed for the diffusion brazing. The phenomena of dissolution and solidification were included into the model. A thermodynamic justification for the isothermal soldering occurrence in meta-stable conditions was developed. It involved the application of the criterion of higher temperature of the solid / liquid (s/l) interface. The dissolution of the filler metal in the substrate was described by the solute concentration within the dissolution zone (liquid film) situated at the substrate surface. The selection of the  parameter was justified by the Thermocalc calculation of the Ni-Al phase diagram for meta-stable equilibrium. According to the model assumptions, the solidification was accompanied by undercooled peritectic reactions resulting in formation of the intermetallic phases. The average Al – solute concentration measured across a given Al₃Ni₂/Al₃Ni/Al₃Ni₂ joint confirmed that the solute concentration was conserved within the joint sub-layers. The Ni-Al phase diagram for meta-stable equilibrium referred to the solidification was also calculated by means of the Thermocalc Software. It allowed to locate the solidification path, s/l interface path and redistribution path onto the mentioned diagram. Superposition of both calculated phase diagrams was also given to show that the joint formation occurred cyclically under the meta-stable conditions. The measured  parameter was introduced into the proposed model as an initial condition in order to solve the formulated differential equation describing solute redistribution after solidification. Isothermal formation of the Ni/Al/Ni joints has been performed at different temperatures. The following  temperatures have been applied: 700, 750, 800, 850, 900, 950, 1000 ⁰C. The solidification was arrested and the actual morphologies frozen. It allowed to make a measurement of the Al-solute concentration across each joint by means of the  EDAX micro-analyzer to estimate its average concentration, .  Regardless the  - temperature, the solidification path was always the same.

Anahtar Kelimeler

meta-stable equilibrium, joint formation model, dissolution, solidification

Kaynakça

• Chuang, Y.K., Reinisch, D. & Schwerdtfeger, K. (1975). Kinetics of Diffusion Controlled Peritectic Reaction During Solidification of Iron-Carbon Alloys, Metallurgical Transactions, 6(A), 235-238.
• Kloch, J., Guzik, E., Janczak-Rusch, J., Kopyciński, D., Rütti, T., Kim, J., Lee, H.M. & Wołczyński, W. (2005). Morphological Characteristics of the Multi- layer/Substrate Systems, Proceedings of the 9th European Congress on Stereology and Image Analysis, Zakopane (Poland), 375-382.
• Jacobson, D.M. & Humpston, G. (1992). Diffusion Soldering, Soldering & Surface Mount Technology,10, 27-32.
• Tuah-Poku, I., Dollar, M. & Massalski, T. (1988). A Study of the Transient Liquid Phase Bonding Process Applied to a Ag/Cu/Ag Sandwich Joint, Metallurgical Transactions, 19A, 675-686.
• Umeda, T., Okane, T. & Kurz,W. (1996), Phase Selection during Solidification of Peritectic Alloys, Acta Materialia, 44, 4209-4216.
• Wołczyński, W., Guzik, E., Kopyciński, D., Himemiya, T. & Janczak-Rusch, J. (2006a). Mass Transport during Diffusion Soldering or Brazing at the Constant Phelan, D., Reid, M. & Dippenaar, R. (2006), Kinetics of Temperature, Proceedings of the 13th International Heat Transfer Conference – Sydney (Australia), ed. Begell House, eds. G.de Vahl Davis & E.Leonardi, CD, MST- 11, 12 pages.
• Wołczyński, W., Kloch, J., Janczak-Rusch, J., Kurzydłowski, K. & Okane, T. (2006b). Segregation Profiles in Diffusion Soldered Ni/Al/Ni Interconnections, Materials Science Forum, 508, 385- 392. the Peritectic Phase Transformation: In-situ Measurements and Phase Field Modelling, Metallurgical and Materials Transactions, 37A, 985- 994.