TY  - JOUR
T1  - Microwave-Cured Pervious Geopolymer Concrete: Role of Aggregate Gradation
TT  - Mikrodalga Kürü ile Üretilen Geçirimli Geopolimer Beton: Agrega Gradasyonunun Rolü
AU  - Gültekin, Adil
PY  - 2025
DA  - July
Y2  - 2025
DO  - 10.7212/karaelmasfen.1672641
JF  - Karaelmas Fen ve Mühendislik Dergisi
PB  - Zonguldak Bulent Ecevit University
WT  - DergiPark
SN  - 2146-7277
SP  - 117
EP  - 131
VL  - 15
IS  - 2
LA  - en
AB  - In this study, microwave technology was used as an alternative curing method, and the effect of aggregate gradation on the properties of fly ash-based pervious geopolymer concrete (PGC) were examined. Microwave-cured PGCs were produced, with one mixture containing only coarse aggregates in the 8-16 mm size range, while the others incorporated partial aggregate replacements-25% of the total aggregate content with finer aggregates in the 4-8 mm and 0.5-4 mm size ranges. For the sake of comparison, oven-cured PGC was also produced. It was determined that the compressive strength of 5 minutes microwave-cured concretes at 700-watt power level varied between 9.7 MPa-12.2 MPa, depending on the aggregate gradation, and these values were higher than the compressive strength (8.2 MPa) of the oven-cured concrete produced at 90°C for 24 hours. The water permeability of microwave-cured concretes decreased with the substitution of smaller-sized aggregate, and the mixture with the highest permeability was the oven-cured one due to the difference in paste structure between oven and microwave curing proven by scanning electron microscope (SEM) investigations. When the effect of aggregate gradation was examined in concretes produced with microwave curing, it was observed that a reduction in aggregate gradation resulted in decreased compressive strength and water permeability, accompanied by an increase in Cantabro abrasion losses. The results revealed that microwave technology has the potential for the production of pervious geopolymer building materials. Microwave technology reduced energy consumption and curing time by 91.4% and 99.7%, respectively.
KW  - Aggregate gradation
KW  - energy saving
KW  - microwave curing
KW  - pervious geopolymer
N2  - Bu çalışmada, mikrodalga teknolojisi alternatif bir kür yöntemi olarak kullanılmış ve agrega gradasyonunun uçucu kül esaslı geçirimli geopolimer beton özellikleri üzerindeki etkisi incelenmiştir. Bir tanesinde sadece 8-16 mm elek aralığındaki agrega kullanılırken, diğerlerinde toplam agrega miktarının %25’i, 4-8 mm ve 0.5-4 mm elek aralıklarındaki agregalarla ağırlıkça yer değiştirilerek farklı betonlar üretilmiştir. Karşılaştırma amacıyla, etüv kürüne tabi tutularak üretilen geçirimli geopolimer beton kullanılmıştır. Mikrodalga kürüyle, 700 watt güç seviyesinde 5 dakika kürlemeyle üretilen betonların basınç dayanımlarının, agrega gradasyonuna bağlı olarak 9.7 MPa-12.2 MPa arasında değiştiği ve bu değerlerin, 90°C’de 24 saat etüvde kürlenen serinin basınç dayanımından (8.2 MPa) daha yüksek olduğu belirlenmiştir. Agrega gradasyonunun küçülmesi, betonların su geçirimliliğini azaltırken; en yüksek su geçirgenliğinin etüv kürü ile üretilen seride elde edildiği belirlenmiştir. Elektron mikroskobu incelemeleri bu durumun iki kür yöntemi ile üretilen betonların hamur yapısındaki farklılıktan kaynaklandığını ortaya koymuştur. Agrega gradasyonunun mikrodalga kürlü betonlar üzerindeki etkisi incelendiğinde, agrega gradasyonunun küçülmesi ile basınç dayanımı ve su geçirgenliğinin azaldığı, Cantabro aşınma kayıplarının ise arttığı görülmüştür. Elde edilen sonuçlar, mikrodalga teknolojisinin geçirimli geopolimer yapı malzemesi üretimi için potansiyel taşıdığını göstermiştir. Mikrodalga kürleme yöntemi, enerji tüketimini %91.4 ve kür süresini %99.7 oranında azaltmıştır.
CR  - AlShareedah, O., Nassiri, S. 2021. Pervious concrete mixture optimization, physical, and mechanical properties and pavement design: A review. J. Clean. Prod., 288: 125095. Doi: 10.1016/j.jclepro.2020.125095
CR  - Arafa, AS., Mohd Ali, AZ., Rahmat, SN., Lee, YL. 2017. Optimum mix for pervious geopolymer concrete (GEOCRETE) based on water permeability and compressive strength. MATEC Web Conf., 103: 01024. Doi: 10.1051/matecconf/201710301024
CR  - Aschoff, J., Partschefeld, S., Schneider, J., Osburg, A. 2024. Effect of microwaves on the rapid curing of metakaolin- and aluminum orthophosphate-based geopolymers. Materials, 17(2): 463. Doi: 10.3390/ma17020463
CR  - ASTM. 2013. Standard Test Method for Determining Potential Resistance to Degradation of Pervious Concrete by Impact and Abrasion (ASTM C1747), USA.
CR  - ASTM. 2014. Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (ASTM C1688), USA.
CR  - Ayawanna, J., Poowancum, A. 2024. Enhancing flexural strength of metakaolin-based geopolymer reinforced with different types of fibers. Sustain. Chem. Pharm., 37: 101439. Doi: 10.1016/j.scp.2024.101439
CR  - Azad, AM., Anshul, A., Azad, N., Samarakoon, SMSMK., Yadav, R., Bherwani, H., Gupta, A., Gebremariam, KF. 2022. Pervious geopolymer concrete as sustainable material for environmental application. Mater. Lett., 318: 132176. Doi: 10.1016/j.matlet.2022.132176
CR  - Chen, X., Guo, Y., Ding, S., Zhang, H., Xia, F., Wang, J., Zhou, M. 2019. Utilization of red mud in geopolymer-based pervious concrete with function of adsorption of heavy metal ions. J. Clean. Prod., 207: 789–800. Doi: 10.1016/j.jclepro.2018.09.263
CR  - Chen, X., Niu, Z., Zhang, H., Guo, Y., Liu, M., Zhou, M. 2021. Study on the metakaolin-based geopolymer pervious concrete (MKGPC) and its removal capability of heavy metal ions. Int. J. Pavement Eng., 22(9): 1181-1192. Doi: 10.1080/10298436.2019.1667499
CR  - Chindaprasirt, P., Jitsangiam, P., Chalee, W., Rattanasak, U. 2021. Case study of the application of pervious fly ash geopolymer concrete for neutralization of acidic wastewater. Case Stud. Constr. Mater., 15: e00770. Doi: 10.1016/j.cscm.2021.e00770
CR  - Dong, Z., Ma, H., Feng, W., Nie, Y., Shi, H. 2022. Achieving superior high-strength geopolymer via the synergistic effect of traditional oven curing and microwave curing. Constr. Build. Mater., 357: 129406. Doi: 10.1016/j.conbuildmat.2022.129406
CR  - Elango, KS., Gopi, R., Saravanakumar, R., Rajeshkumar, V., Vivek, D., Raman, SV. 2021. Properties of pervious concrete – A state of the art review. Mat. Today Proc., 45: 2422–2425. Doi: 10.1016/j.matpr.2020.10.839
CR  - Ganesh, CA., Vinod Kumar, M., Kanniga Devi, R., Srikar, P., Prasad, S., Manoj Kumar, M., Sarath, RP. 2021. Pervious geopolymer concrete under ambient curing. Mat. Today Proc., 46: 2737–2741. Doi: 10.1016/j.matpr.2021.02.425
CR  - Graytee, A., Sanjayan, JG., Nazari, A. 2018. development of a high strength fly ash-based geopolymer in short time by using microwave curing. Ceram. Int., 44(7): 8216–8222. Doi: 10.1016/j.ceramint.2018.02.001
CR  - Guan, X., Luo, W., Liu, S., Hernandez, AG., Do, H., Li, B. 2023. Ultra-high early strength fly ash-based geopolymer paste cured by microwave radiation. Dev. Built Environ., 14: 100139. Doi: 10.1016/j.dibe.2023.100139
CR  - Gultekin, A., Ramyar, K. 2022. Effect of curing type on microstructure and compressive strength of geopolymer mortars. Ceram. Int., 48(11): 16156–16172. Doi: 10.1016/j.ceramint.2022.02.163
CR  - Huang, W., Wang, H. 2022. Multi-aspect engineering properties and sustainability impacts of geopolymer pervious concrete. Compos. B Eng., 242: 110035. Doi: 10.1016/j.compositesb.2022.110035
CR  - Huang, W., Wang, H. 2021. Geopolymer pervious concrete modified with granulated blast furnace slag: Microscale characterization and mechanical strength. J. Clean. Prod., 328: 129469. Doi: 10.1016/j.jclepro.2021.129469
CR  - Jivani, R., Panchal, VR., Bhavsar, JK. 2018. Performance assessment of pervious geopolymer concrete using metakaolin. Int. J. Sci. Res. Sci. Eng. Technol., 4(5): 227-233.
CR  - Khalil, WI., Frayyeh, QJ., Abed, HT. 2019. Properties of metakaolin based pervious geopolymer concrete. IOP Conf. Series: Mat. Sci. Eng., 518(2): 022056. Doi: 10.1088/1757-899X/518/2/022056
CR  - Khalil, WJ., Frayyeh, QT., Abed, H. 2021. Effect of ordinary Portland cement on some properties of pervious geopolymer concrete. Eng. Tech. J., 39(4A): 668–674. Doi: 10.30684/etj.v39i4A.1793
CR  - Luo, Y., Lv, Y., Wang, D., Jiang, Z., Xue, G. 2023. The Influence of coarse aggregate gradation on the mechanical properties, durability, and plantability of geopolymer pervious concrete. Constr. Build. Mater., 382: 131246. Doi: 10.1016/j.conbuildmat.2023.131246
CR  - Maguesvari, MU., Muthaiyan, P., Yugasini, S., Ammaiappan M. 2020. Experimental studies on pervious geopolymer concrete. IOP Conf. Ser.: Mater. Sci. Eng., 989: 012032. Doi: 10.1088/1757-899X/989/1/012032
CR  - Maguesvari, MU., Narasimha, VL. 2013. Studies on characterization of pervious concrete for pavement applications. Procedia Soc. Behav. Sci., 104: 198–207. Doi: 10.1016/j.sbspro.2013.11.112
CR  - Nanda, RP., Priya, N. 2024. Geopolymer as stabilizing materials in pavement constructions: A review. Clean. Waste Syst., 7: 100134. Doi: 10.1016/j.clwas.2024.100134
CR  - Nurruddin, MF., Haruna, S., Mohammed, BS., Shaaban, IG. 2018. Methods of curing geopolymer concrete: A review. Int. J. Adv. Appl. Sci., 5(1): 31–36. Doi: 10.21833/ijaas.2018.01.005
CR  - Raghwani, JR., Shah, D., Bhavsar, JK. 2016. Performance assessment of pervious concrete by using silica fume.” J. Civ. Eng. Environ. Technol., 3(4): 269-273.
CR  - Sanjaya, N., Saloma H., Juliantina, I., Nurjannah, SA. 2021. Compressive strength, permeability and porosity analysis of pervious concrete by variation of aggregate and compacting method. J. Phys. Conf. Ser., 1783(1): 012073. Doi: 10.1088/1742-6596/1783/1/012073
CR  - Sata, V., Wongsa, A., Chindaprasirt, P. 2013. Properties of pervious geopolymer concrete using recycled aggregates. Constr. Build. Mater., 42: 33–39. Doi: 10.1016/j.conbuildmat.2012.12.046
CR  - Shi, S., Li, H., Fabian, M., Sun, T., Grattan, KTV., Xu, D., Basheer, PAM., Bai, Y. 2016. Alkali-activated fly ash manufactured with multi-stage microwave curing. Fourth International Conference on Sustainable Construction Materials and Technologies, Las Vegas, USA.
CR  - Somaratna, J., Ravikumar, D., Neithalath, N. 2010. Response of alkali activated fly ash mortars to microwave curing. Cem. Concr. Res., 40(12): 1688–1696. Doi: 10.1016/j.cemconres.2010.08.010
CR  - Sun, Z., Lin, X., Vollpracht, A. 2018. Pervious concrete made of alkali activated slag and geopolymers. Constr. Build. Mater., 189: 797–803. Doi: 10.1016/j.conbuildmat.2018.09.067
CR  - Suwan, T., Fan, M. 2014. “Influence of OPC replacement and manufacturing procedures on the properties of self-cured geopolymer.” Constr. Build. Mater., 73: 551–561. Doi: 10.1016/j.conbuildmat.2014.09.065
CR  - Tempest, B., Sanusi, O., Gergely, J., Ogunro, V., Weggel, D. 2009. Compressive strength and embodied energy optimization of fly ash based geopolymer concrete. 2009 World of Coal Ash (WOCA) Conference, USA.
CR  - Tho-in, T., Sata, V., Chindaprasirt, P., Jaturapitakkul, C. 2012. Pervious high-calcium fly ash geopolymer concrete. Constr. Build. Mater., 30: 366–371. Doi: 10.1016/j.conbuildmat.2011.12.028
CR  - Yavuz, D., Yazici, S. 2023. Experimental study of aggregate size and gradation on pervious concretes' mechanic, hydraulic, and surface properties. Struct. Concr., 24:5451–5464. Doi: 10.1002/suco.202200234
CR  - Yilmazer Polat, B. 2023. The Influence of microwave curing on the strength of silica fume-added fly ash-based geopolymer mortars. J. Sustain. Constr. Mater. Technol., 8(3): 207–215. Doi: 10.47481/jscmt.1315096
CR  - Zaetang, Y., Wongsa, A., Sata, V., Chindaprasirt, P. 2015. Use of coal ash as geopolymer binder and coarse aggregate in pervious concrete. Constr. Build. Mater., 96: 289–295. Doi: 10.1016/j.conbuildmat.2015.08.076
CR  - Zhang, B., Liu, Y., Pan, Z., Li, L., Huang, Y., Wang, Z., Chen, J., Lao, W., Liu, F., Zhu, H., Xiong, Z. 2024. The microstructure and mechanical properties of recycled metakaolinite-based geopolymer: Dependence of recycled powder replacement ratio. J. Build. Eng., 85: 108730. Doi: 10.1016/j.jobe.2024.108730
CR  - Zhang, J., Sun, H., Shui, X., Chen, W. 2023. Experimental investigation on the properties of sustainable pervious concrete with different aggregate gradation. Int. J. Concr. Struct. Mater., 17:64. Doi: 10.1186/s40069-023-00625-0
CR  - Zhou, G., Luo, Y., Xue, G. 2023. Study on mechanical properties of metakaolin based geopolymer pervious concrete. E3S Web Conf., 439:02006. Doi: 10.1051/e3sconf/202343902006
CR  - Ziada, M., Tanyildizi, H., Uysal, M. 2024. The influence of carbon nanotube on underwater geopolymer paste based on metakaolin and slag. Constr. Build. Mater., 414: 135047. Doi: 10.1016/j.conbuildmat.2024.135047
UR  - https://doi.org/10.7212/karaelmasfen.1672641
L1  - https://dergipark.org.tr/en/download/article-file/4757593
ER  -