TY  - JOUR
T1  - Multi-Criteria Performance Analysis of Dry, Vortex Air and Compressed Air Environments in Turning Hastelloy X Superalloy
AU  - Siyambaş, Yusuf
AU  - Akdulum, Aslan
PY  - 2025
DA  - August
Y2  - 2025
JF  - Gazi Journal of Engineering Sciences
JO  - GJES
PB  - Parantez Teknoloji
WT  - DergiPark
SN  - 2149-9373
SP  - 243
EP  - 253
VL  - 11
IS  - 2
LA  - en
AB  - Hastelloy X superalloy, which exhibits superior performance under harsh conditions such as extreme temperature, oxidation, and corrosion, is widely used in the aviation and energy sectors but causes significant problems in machining due to its difficult machinability properties. This situation has brought up the need for alternative cooling strategies to reduce cutting forces and temperatures during machining, improve surface quality, and minimize environmental impacts. In this research, the impacts of varying cutting variables (depth of cut, feed rate, and cutting speed) on cutting force (FR), surface roughness (Ra), and cutting temperature (T) in the turning of Hastelloy X superalloy under three different machining environments (dry, vortex air, and compressed air) were experimentally investigated. The Taguchi L9 orthogonal layout was utilized for the experimental design, and simultaneous optimization of multiple performance outcomes was carried out by the grey relational analysis (GRA) technique. According to the findings, the lowest FR and Ra occurred in dry, compressed air and vortex air processing environments, respectively. The lowest values in terms of T were obtained in compressed air, vortex air, and dry machining environments, respectively. In summary, the effect of cooling conditions on T was not reflected in FR and Ra. As a result of GRA optimization, where all performance criteria were evaluated together, the most suitable machining condition was determined to be a dry machining environment, an 80 m/min cutting speed, a 0.075 mm/rev feed rate, and a 0.8 mm cutting depth. Vortex air and compressed air environments have been evaluated as a strong alternative to dry environments.
KW  - Sustainable processing environments
KW  - cutting force
KW  - cutting temperature
KW  - surface roughness
KW  - grey relational analysis
CR  - [1] A. Altin, “Optimization of the turning parameters for the cutting forces in the Hastelloy X superalloy based on the Taguchi method,” Materials and  technology, vol. 48, no. 2, pp. 249–254, 2014.
[2] M. S. Alsoufi and S. A. Bawazeer, “Predictive Modeling of Surface Integrity and Material Removal Rate in Computer Numerical Control Machining: Effects of Thermal Conductivity and Hardness,” Materials (Basel), vol. 18, no. 7, 2025. doi: 10.3390/ma18071557
CR  - [3] H. Hegab and H. A. Kishawy, “Towards sustainable machining of inconel 718 using nano-fluid minimum quantity lubrication,” Journal of     Manufacturing and Materials Processing, vol. 2, no. 3, 2018. doi: 10.3390/jmmp2030050
CR  - [4] K. Venkatesan, S. Devendiran, K. Nishanth Purusotham, and V. S. Praveen, “Study of machinability performance of Hastelloy-X for nanofluids, dry  with coated tools,” Materials and Manufacturing Processes, vol. 35, no. 7, pp. 751–761, 2020. doi: 10.1080/10426914.2020.1729990
CR  - [5] T. B. Oschelski, W. T. Urasato, H. J. Amorim, and A. J. Souza, “Effect of cutting conditions on surface roughness in finish turning Hastelloy® X superalloy,” Materials Today: Proceedings, vol. 44, pp. 532–537, 2021. doi: 10.1016/j.matpr.2020.10.211
CR  - [6] V. Sivalingam, J. Sun, S. K. Mahalingam, L. Nagarajan, et al., “Optimization of process parameters for turning hastelloy x under different machining environments using evolutionary algorithms: A comparative study,” Applied Sciences, vol. 11, no. 20, pp. 1–18, 2021. doi: 10.3390/app11209725
CR  - [7] Q. Zhou, V. Sivalingam, J. Sun, P. K. Murugasen, et al., “Understanding the machining induced tribological mechanism of Hastelloy-X under sustainable cooling/lubrication conditions,” The International Journal of Advanced Manufacturing Technology, vol. 123, no. 3–4, pp. 973–983, 2022. doi: 10.1007/s00170-022-10243-x
CR  - [8] R. L. de Paiva, R. de Souza Ruzzi, L. R. de Oliveira, E. P. Bandarra Filho, et al., “Experimental study of the influence of graphene platelets on the performance of grinding of SAE 52100 steel,” The International Journal of Advanced Manufacturing Technology, vol. 110, no. 1–2, pp. 1–12, 2020. doi: 10.1007/s00170-020-05866-x
CR  - [9] A. Race, I. Zwierzak, J. Secker, J. Walsh, et al., “Environmentally sustainable cooling strategies in milling of SA516: Effects on surface integrity of dry, flood and MQL machining,” Journal of Cleaner Production, vol. 288, p. 125580, 2021. doi: 10.1016/j.jclepro.2020.125580
CR  - [10] S. Yaqoob, J. A. Ghani, A. Z. Juri, S. S. Muhamad, et al., “A review of sustainable hybrid lubrication (Cryo-MQL) techniques in machining processes,” The International Journal of Advanced Manufacturing Technology, vol. 131, no. 1, pp. 151–169, 2024. doi: 10.1007/s00170-024-13135-4
CR  - [11] S. H. Ali, Y. A. O. Yu, W. U. Bangfu, Z. H. A. O. Biao, et al., “Recent developments in MQL machining of aeronautical materials: A comparative review,” Chinese Journal of Aeronautics, vol. 38, no. 1, p. 102918, 2024. doi: 10.1016/j.cja.2024.01.018
CR  - [12] C. Courbon, L. Sterle, M. Cici, and F. Pusavec, “Tribological effect of lubricated liquid carbon dioxide on TiAl6V4 and AISI1045 under extreme contact conditions,” Procedia Manufacturing, vol. 47, pp. 511–516, 2020. doi: 10.1016/j.promfg.2020.04.139
CR  - [13] S. Polo, E. M. Rubio, M. M. Marín, and J. M. Sáenz de Pipaón, “Evolution and Latest Trends in Cooling and Lubrication Techniques for Sustainable Machining: A Systematic Review,” Processes, vol. 13, no. 2, 2025. doi: 10.3390/pr13020422
CR  - [14] D. Gürkan, S. A. Yaşar, G. Uzun, and İ. Korkut, “Vorteks SoğutmYöntemi̇ni̇n Talaşlı İmalat Yöntemleri ve Kesme Parametreleri̇ne Göre İncelenmesi̇,” Gazi University Journal of Science Part C: Design and Technology, vol. 8, no. 3, pp. 730–745, 2020. doi: 10.29109/gujsc.727746
CR  - [15] Y. Özçatalbaş and A. Baş, “Tornalamada hava püskürtme ile soğutmanın kesme kuvvetleri ve takım ömrüne etkilerinin araştırılması,” Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, vol. 21, no. 3, 2013.
CR  - [16] Y. Siyambaş and A. Akdulum, “Prediction of surface roughness using different features in vortex cooled turning process of Ti6Al4V alloy,” Measurement, vol. 237, 2024. doi: 10.1016/j.measurement.2024.115258
CR  - [17] A. Díaz-Álvarez, J. Díaz-Álvarez, J. L. Cantero, and M. H. Miguélez, “Using Carbide Tools : Haynes 282 and Inconel 718 Comparison,” Metals, vol. 11 no. 12, 2021. doi.org/10.3390/met11121916
CR  - [18] M. A. Sofuoğlu, F. H. Çakır, S. Gürgen, S. Orak, et al., “Experimental investigation of machining characteristics and chatter stability for Hastelloy-X with ultrasonic and hot turning,” The International Journal of Advanced Manufacturing Technology, vol. 95, no. 1–4, pp. 83–97, 2018. doi: 10.1007/s00170-017-1153-9
CR  - [19] Y. Siyambaş and Y. Turgut, “Experimental and statistical investigation of mechanical properties and surface roughness in additive manufacturing with selective laser melting of AlSi10Mg alloy,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 45, no. 10, pp. 1–15, 2023. doi: 10.1007/s40430-023-04445-x
CR  - [20] A. Akdulum and Y. Kayir, “Experimental investigation and optimization of process stability in drilling of Al 7075-T651 using indexable insert drills,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 45, no. 8, pp. 1–20, 2023. doi: 10.1007/s40430-023-04303-w
CR  - [21] S. Yağmur, “The effects of cooling applications on tool life, surface quality, cutting forces, and cutting zone temperature in turning of Ni-based Inconel 625,” The International Journal of Advanced Manufacturing Technology, vol. 116, no. 3–4, pp. 821–833, 2021. doi: 10.1007/s00170-021-07489-2
CR  - [22] R. Çakıroğlu and M. Günay, “Comprehensive analysis of material removal rate, tool wear and surface roughness in electrical discharge turning of L2 tool steel,” Journal of Materials Research and Technology, vol. 9, no. 4, pp. 7305–7317, 2020. doi: 10.1016/j.jmrt.2020.04.060
CR  - [23] R. Çakıroğlu, “Analysis of Ranque–Hilsch vortex tube cooling performance in respect of cutting temperature, resultant cutting force and chip morphology in turning of BeCu alloy,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 44, no. 8, pp. 1–18, 2022. doi: 10.1007/s40430-022-03689-3
CR  - [24] A. Anurag, R. Kumar, K. K. Joshi, and R. K. Das, “Analysis of Chip Reduction Coefficient in Turning of Ti-6Al-4V ELI,” Materials science and engineering, vol. 390, no. 1, 2018. doi: 10.1088/1757-899X/390/1/012113
CR  - [25] K. V. Sudhakar, J. C. Cisneros, H. Cervantes, and C. G. Pineda, “Machining characteristics and fracture morphologies in a copper-beryllium (Cu-2Be) alloy,” Journal of materials engineering and performance, vol. 15, no. 1, pp. 117–121, 2006. doi: 10.1361/105994906X83510
CR  - [26] M. Akgün and H. Demir, “Experimental and numerical analysis of the effect of cutting parameters on cutting force and chip formation in turning process,” El-Cezeri,, vol. 8, no. 2, pp. 897–908, 2021. doi: 10.31202/ecjse.892705
CR  - [27] S. Ehsan, S. A. Khan, and M. Rehman, “Defect-free high-feed milling of Ti-6Al-4V alloy via a combination of cutting and wiper inserts,” The International Journal of Advanced Manufacturing Technology, vol. 114, no. 1–2, pp. 641–653, 2021. doi: 10.1007/s00170-021-06875-0
CR  - [28] T. Ding, S. Zhang, Y. Wang, and X. Zhu, “Empirical models and optimal cutting parameters for cutting forces and surface roughness in hard milling of AISI H13 steel,” The International Journal of Advanced Manufacturing Technology, vol. 51, no. 1–4, pp. 45–55, 2010. doi: 10.1007/s00170-010-2598-2
CR  - [29] S. Yağmur, “Investigation of the effect of minimum quantity lubrication and Ranque–Hilsch vortex tube cooling on cutting forces, surface roughness and cutting zone temperature in turning Al 6082 T4 alloy,” Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2023. doi: 10.1177/09544089231209007
CR  - [30] R. Çakiroǧlu and A. Acir, “Optimization of cutting parameters on drill bit temperature in drilling by Taguchi method,” Measurement, vol. 46, no. 9, pp. 3525–3531, 2013. doi: 10.1016/j.measurement.2013.06.046
CR  - [31] M. C. Shaw and J. O. Cookson, Metal cutting principles, New York Oxford University Press, vol. 2–3, 2005.
CR  - [32] J. S. Hu, D. X. Liu, Y. Z. Liu, C. X. Yue, et al., “Experimental investigation on air cooling of GCr15”. Key Engineering Materials, vol. 375, pp. 197-200, 2008. doi.org/10.4028/www.scientific.net/KEM.375-376.197
CR  - [33] Z. Taha, H. A. Salaam, T. T. Ya, S. Y. Phoon, et al., “Vortex tube air cooling: The effect on surface roughness and power consumption in dry turning”. International Journal of Automotive and Mechanical Engineering, vol. 8, pp. 1477-1586, 2013. doi: 10.15282/ijame.8.2013.34.0122
CR  - [34] A. Kaçal, “Effect of machining parameters on turning of Inconel X750 using PVD coated carbide inserts.” Journal of Scientific & Industrial Research, vol. 79 no. 3, pp. 226-231, 2022.
UR  - https://dergipark.org.tr/en/pub/gmbd/issue//1684483
L1  - https://dergipark.org.tr/en/download/article-file/4809173
ER  -