TY - JOUR T1 - Elektro Çekim Yöntemi ile Haloysit Katkılı Biyo-Bazlı Termoplastik Poliüretan Nanolif Üretimi ve Karakterizasyonu TT - Production and Characterization of Halloysite Filled Bio-Based Thermoplastic Polyurethane Nanofibers Via Electrospinning Method AU - Seydibeyoğlu, Mehmet Özgür AU - Akın, Ecem AU - Demiroğlu Mustafov, Sibel AU - Alyamaç, Elif PY - 2020 DA - December JF - Tekstil ve Mühendis PB - Tekstil Mühendisleri Odası WT - DergiPark SN - 1300-7599 SP - 218 EP - 229 VL - 27 IS - 120 LA - tr AB - Bu çalışmada, elektro çekim tekniği kullanılarak biyokompozit nanolif üretimi amaçlanmakta olup biyokompozit yapınınoluşturulabilmesi için biyo-bazlı termoplastik poliüretan (BioTPU) ile yerli kaynaklardan elde edilen haloysit (HST) mineralikullanıldı. Düzgün morfolojiye sahip nanolif üretimi için elektro çekim parametreleri optimize edilerek en uygun parametreye sahippolimer çözeltisi belirlendi ve farklı konsantrasyonlarda HST katkılı BioTPU nanolifleri üretildi. Çalışmalar sırasında, haloysitin lifmorfolojisi üzerine etkilerini görmek için elektro çekim işleminden önce rotasyonel reometre ile çözeltilerin reolojik davranışlarıincelendi. Elde edilen nanoliflerin yüzey morfolojilerini görüntülemek için taramalı elektron mikroskobu (SEM) kullanıldı.Nanoliflerin yapısına eklenen haloysitin, nanolif hidrofilitesi üzerinde yaptığı etkileri gözlemlemek için temas açısı analizlerigerçekleştirildi. Reoloji sonuçlarına göre haloysitin çözelti viskozitesini belli bir konsantrasyona kadar (% 0.3 HST) arttırdığı dahasonra viskozite, depolama modülü (G') ve kayıp modül (G'') değerleri üzerinde düşmelere neden olduğu tespit edildi. SEM’den alınangörüntüler doğrultusunda, haloysitin nanoliflerin yapısına tutunduğu görüldü. Ayrıca yapıya eklenen haloysitin lif çaplarını arttırdığıve lif ekseni boyunca, lif kesitinin üniform olarak dağılmadığı tespit edildi. Nanoliflere ait temas açısı analizi sonuçlarına göre eldeedilen nanoliflerin hidrofobik bir yüzeye sahip olduğu ve haloysitin, nanolifilerin temas açılarını azalttığı sonucuna varıldı. KW - Biyo-bazlı termoplastik poliüretan KW - biyokompozit KW - elektro çekim KW - haloysit KW - nanolif N2 - In this study, it was aimed to produce biocomposite nanofibers by using electrospinning technique and to formbiocomposite structure, bio-based thermoplastic polyurethane (BioTPU) and halloysite (HST) mineral obtained from natural sourceswere used. Electrospinning parameters have been optimized for the production of nanofibers with smooth morphology and thepolymer solution with the most suitable parameter was determined. Different concentrations of HST filled BioTPU nanofibers wereproduced and the rheological behavior of the solutions was investigated with a rotational rheometer before electrospinning to observethe effects of halloysite on fiber morphology. Fourier transform infrared spectroscopy (FTIR) analysis was carried out to determinethe chemical composition of acquired nanofibers, and scanning electron microscopy (SEM) was used to monitor surfacemorphologies. Contact angle measurements were carried out to observe the effects of halloysite on the hydrophilicity of nanofiber.According to rheology results, it has been found out that the solution viscosity, storage modulus (G') and loss modulus (G'') ofhalloysite increased up to a certain concentration (0.3 % HST), but later caused falls on viscosity. According to the results of FTIRanalysis, there is no chemical bond between halloysite and BioTPU, but SEM images show that halloysite was added to the structureof nanofibers. It was also found that the halloysite added to the structure increased the fiber diameters and that the fiber cross-sectionwas not uniformly distributed along the fiber axis. The results of contact angle analysis indicated that acquired nanofibers havehydrophobic surface and the added halloysite decreases contact angles of nanofibers. CR - 1. De Marco, B. A., Rechelo, B. S., Totoli, E. G., Kogawa, A. C., & Salgado, H. R. N., (2019), Evolution of green chemistry and its multidimensional impacts: a review, Saudi Pharmaceutical Journal, 27(1), 1–8. CR - 2. Correa, J. P., Montalvo-Navarrete, J. M., & Hidalgo-Salazar, M. A., (2019), Carbon footprint considerations for biocomposite materials for sustainable products: a review, Journal of Cleaner Production, 208, 785–794. CR - 3. Fowler, P. A., Hughes, J. M., & Elias, R. M., (2006), Biocomposites: technology, environmental credentials and market forces, Journal of the Science of Food and Agriculture, 86, 1781– 1789. CR - 4. Jawaid, M., Sapuan, S. M., & Alothman, O. Y. (Eds.), (2017), Green biocomposites manufacturing and properties, Springer International Publishing, Gewerbestrasse. CR - 5. Reddy, M. M., Vivekanandhan, S., Misra, M., Bhatia, S. K., Mohanty, A. K, (2013), Biobased plastics and bionanocomposites: Current status and future opportunities, Progress in Polymer Science 38, 1653– 1689. CR - Kaynakların tamamı makale dosyası içerisinde yer almaktadır! UR - https://dergipark.org.tr/en/pub/teksmuh/issue//851276 L1 - https://dergipark.org.tr/en/download/article-file/1481087 ER -