ÖN ALAŞIMLANDIRILMIŞ Ti6Al4V TOZU İLE Ti(CP) TOZUNUN SIKIŞTIRILABİLME ŞARTLARININ ARAŞTIRILMASI

Year 2018, Volume: 6 Issue: 1, 175 - 181, 30.03.2018

Muqdad Naser M. Al-dulaımı Remzi Varol

https://doi.org/10.21923/jesd.365213

Abstract

TM ile
üretilen titanyum ürünleri birçok endüstriyel alanda, tıp alanında ve diğer
sektörlerde kullanılmaktadır. Bu çalışmanın amacı farklı sıkıştırma
basınçlarında titanyum tozuna ilave edilen yağlayıcı (Zn-Stearat) miktarlarının
ham yoğunluğa, ham dayanıma, kalıptan ürünün çıkartılması için gerekli olan
çıkartma kuvvetine, sinterlenmiş yoğunluğa ve diğer mekanik özelliklere
etkisinin araştırılmasının yanı sıra kırık yüzeylerin incelenmesidir. Bu
deneysel çalışmada, titanyum tozuna eklenen ve karıştırılan yağlayıcı
miktarları (0.5%, 0.75%, 1% ve 1.1%) olarak belirlenmiş ve bu oranlarla
karıştırılan titanyum tozları farklı basınçlarda (Ti6Al4V için 650- 900 MPa)
ve[Ti(CP)] için 400-650 MPa) sıkıştırılmıştır. Her iki çeşit Titanyum tozundan
kompaktlar 1250Cᵒ sıcaklıkta argon gazlı atmosferik fırında sinterlenmiştir.
Sinterlenmiş numunelere üç nokta eğme deneyi, darbe deneyi, sertlik deneyi ve
SEM-EDS analizleri yapılmıştır. 

Keywords

Ti6Al4V, Toz Metalurjisi, Sıkıştırılabilme, Ön Alaşımlanmdırma Toz

INVESTIGATION ON THE COMPACTABLE CONDITIONS OF TI POWDERS PRE-ALLOYED TI6AL4V AND TI(CP)

Abstract

The
titanium products produced by powder metallurgy method, a decent position among
the other materials and production methods. The aim of this study is to
investigate the effect of lubrication (Zn-Stearat) which added to the titanium
powder at different compaction pressure, to the green density, green strength,
ejecting force to eject the products from the die, sintered density and others
mechanical properties as well as the metallography for fracture surfaces of
specimens. Then, all results of between two type of titanium (Ti6Al4V and Ti
(CP)) powders are compared. In this experimental study, cold pressing with
single acting press are applied. The amounts of lubrications (Zn-Stearat) are
added and mixed with titanium powder is (0.5%, 0.75%, 1% and 1.1%) and each
ratio are compacted in steel die at different compaction pressure (650- 900 MPa
for Ti6Al4V) and (400-650 MPa for Ti (CP)). Two types of titanium powder
compacts are sintered in 1250Cᵒ in argon gas atmospheric furnace. Three-point
bending test, impact test, hardness test and SEM –EDS analysis were applied to
all specimens. 

Keywords

Ti6Al4V, Ti (CP), Powder Metallurgy, Compactability, Pre-alloyed powder

References

• Adams, J. W., Duz, V. A., Moxson, V., & Roy, W. R. Low Cost Blended Elemental Titanium Powder Metallurgy.
• Bosman, H. L., Ve Blaine, D. C. (2014). Influence Of Powder Particle Size Distribution On The Properties Of Press-And-Sintered Titanium And Ti-6al-4v Preforms. Advanced Materials Research, (1019).
• Delavari, M., Salarvand, A., Rahi, A., Ve Shahri, F. (2011). The Effect Of Powder Metallurgy Process Parameters On Mechanical Properties Of Micro And Nano-İron Powder. International Journal Of Engineering, Science And Technology, 3(9), 86-94.
• Fang, Z. Z., Ve Sun, P. (2012). Pathways To Optimize Performance/Cost Ratio Of Powder Metallurgy Titanium–A Perspective. In Key Engineering Materials (Vol. 520, Pp. 15-23). Trans Tech Publications. Gronostajski, Z., Bandoła, P., Ve Skubiszewski, T. (2009). Influence Of Cold And Hot Pressing On Densification Behaviour Of Titanium Alloy Powder Ti6al4v. Archives Of Civil And Mechanical Engineering, 9(2), 47-57.
• Handbook, A. S. M. (1998). Volume 7. Powder Metal Technologies And Applications, 435.
• Hryha, E., Dudrova, E., Ve Bengtsson, S. (2008). Influence Of Powder Properties On Compressibility Of Prealloyed Atomised Powders. Powder Metallurgy, 51(4), 340-342.
• Kateřina Skotnicová, Miroslav Kursa Ve Ivo Szurman. (2014). Powder Metallurgy. University Text Book, Faculty Of Metallurgy And Materials Engineering, Vsb- Technıcal Unıversıty Of Ostrava.
• Liu, X., Chu, P. K., Ve Ding, C. (2004). Surface Modification Of Titanium, Titanium Alloys, And Related Materials For Biomedical Applications. Materials Science And Engineering: R: Reports, 47(3), 49-121.
• Upadhyaya, G. S. (2002). Powder metallurgy technology. Cambridge Int Science Publishing.
• W. Brian James, Hoeganaes Corporation. (2015). Powder Metallurgy Methods and Applications. ASM Handbook, Volume 7, Powder Metallurgy.
• Wang, H., Fang, Z. Z., ve Sun, P. (2010). A critical review of mechanical properties of powder metallurgy titanium. International journal of powder metallurgy, 46(5), 45-57. Welsch, G., Lee, Y. T., Eloff, P. C., Eylon, D., & Froes, F. H. (1983). Deformation behavior of blended elemental ti-6ai-4v compacts. Metallurgical Transactions A, 14(3), 761-769.
• Williams, J. C. (2007). Titanium. Engineering Materials and Processes. Springer.
• Yalçın, B. (2007). Toz metalurjisi yöntemiyle imal edilen titanyum alaşımı implantların temel özelliklerinin araştırılması (Doctoral dissertation, SDÜ Fen Bilimleri Enstitüsü).
• Yan, Y., Nash, G. L., ve Nash, P. (2013). Effect of density and pore morphology on fatigue properties of sintered Ti–6Al–4V. International Journal of Fatigue, 55, 81-91.
• Yu, C. (2014). Ti powder sintering: impurity, sintering atmosphere and alloy design (Doctoral dissertation, ResearchSpace@ Auckland).
• Zak Fang, Z. (2010). Sintering of advanced materials: fundamental and processes.