In this study, the production of full-density Cu-10Sn bronze parts by selective laser melting (SLM) technique and the examination of microstructural, mechanical and corrosion properties were carried out. Cu-10Sn pre-alloyed powders produced by gas atomization technique were shaped using SLM technique within selected parameters and then microstructural properties were determined. Depending on the microstructural properties, the mechanical and corrosion behaviors were determined. The obtained results were compared with similar bronze materials produced by conventional methods. Different characterization techniques were used for microstructural characterization. The microstructure of the Cu-10Sn alloy was observed to consist of dendritic primary α and δ-Cu41Sn11 phases. According to the mechanical test results of the samples produced at densities of 8.75 g cm-3 at room temperature, the yield strength was measured as 420 MPa, the tensile strength was 578 MPa, the elongation was 32 % and the hardness value was 160.3 HV0.2. For the electrochemical experiments, the corrosion rate of the samples was found to be 4.38 mpy. As a result of the productions and experiments, it was determined that the samples produced by the SLM method provide very good mechanical and corrosion properties compared to the literature.
Selective Laser Melting Cu-Sn alloy Microstructure Mechanical Properties Corrosion resistance
FEN-C-YLP-130219-0042
Bu çalışmada, tam yoğunluklu Cu-10Sn bronz parçaların seçici lazer ergitme (SLM) tekniği ile üretilmesi, mikroyapısal, mekanik ve korozyon özelliklerinin incelenmesi gerçekleştirilmiştir. Gaz atomizasyon tekniği ile üretilmiş Cu-10Sn ön-alaşımlı tozlar, seçilen parametreler dahilinde SLM tekniği kullanılarak şekillendirilmiş ve sonrasında mikroyapısal özellikleri belirlenmiştir. Mikroyapısal özelliklere bağlı olarak mekanik ve korozyon davranışlarının belirlenmesi gerçekleştirilmiştir. Elde edilen sonuçlar geleneksel metotlar ile üretilmiş benzer bronz malzemeler ile karşılaştırılmıştır. Mikroyapısal karakterizasyon için farklı inceleme teknikleri kullanılmıştır. Cu-10Sn alaşımının mikroyapısının dendritik birincil α ve δ-Cu41Sn11 fazlarından oluştuğu görülmüştür. 8,75 g cm-3 yoğunluklarda üretilen numunelerin oda sıcaklığında gerçekleştirilen mekanik deney sonuçlarına göre, akma mukavemeti 420 MPa, çekme mukavemeti 578 MPa, % uzama değeri 32 ve sertlik değeri 160,3 HV0.2 olarak ölçülmüştür. Gerçekleştirilen elektrokimyasal deneylere göre numunelerin korozyon hızının 4,38 mpy değerlerinde olduğu görülmüştür. Gerçekleştirilen üretimler ve deneyler sonucunda SLM yöntemiyle üretilen numunelerin literatüre kıyasla oldukça iyi mekanik ve korozyon özellikleri gösterdiği belirlenmiştir.
Bu çalışma Marmara Üniversitesi tarafından desteklenmiştir.
FEN-C-YLP-130219-0042
Bu çalışma Marmara Üniversitesi (Proje no: FEN-C-YLP-130219-0042) tarafından desteklenmiştir.
Primary Language | English |
---|---|
Subjects | Engineering |
Journal Section | Articles |
Authors | |
Project Number | FEN-C-YLP-130219-0042 |
Early Pub Date | June 29, 2022 |
Publication Date | June 29, 2022 |
Published in Issue | Year 2022 Volume: 11 Issue: 2 |
This work is licensed under the Creative Commons Attribution-Non-Commercial-Non-Derivable 4.0 International License.