TY - JOUR T1 - Noise and vibration behavior of a diesel engine operating with CNT-blended fuels and different EGR rates TT - CNT KARIŞIMLI YAKITLAR VE FARKLI EGR ORANLARI İLE ÇALIŞAN BİR DİZEL MOTORUN GÜRÜLTÜ VE TİTREŞİM DAVRANIŞI AU - Çelebi, Samet AU - Demir, Üsame PY - 2025 DA - September Y2 - 2025 DO - 10.18245/ijaet.1651115 JF - International Journal of Automotive Engineering and Technologies PB - Murat CİNİVİZ WT - DergiPark SN - 2146-9067 SP - 199 EP - 214 VL - 14 IS - 3 LA - en AB - In this study, the effects of carbon nanotube (CNT)-blended fuels on engine noise and vibration levels were experimentally investigated in a single-cylinder, air-cooled, direct-injection diesel engine. CNTs were introduced as single-wall (SWCNT) and multi-wall (MWCNT) variants at concentrations of 25 ppm and 50 ppm. Tests were performed at engine loads of 0%, 25%, 50%, 75%, and 100%, and EGR (Exhaust Gas Recirculation) rates of 0%, 10%, and 20%. The results showed a clear trend of increasing noise and vibration levels with rising engine load. For instance, the noise level for D100 fuel rose from 94.84 dB (0% load) to 96.71 dB (100% load), while SW50 increased from 95.92 dB to 97.80 dB, and MW50 from 95.12 dB to 97.61 dB. Regarding vibration, D100 increased from 96.23 m/s² to 96.94 m/s², whereas SW25 showed a rise from 89.17 m/s² to 101.90 m/s², and MW50 maintained more stable values from 98.28 m/s² across the load range. Increasing the EGR rate generally reduced both acoustic parameters, especially under low-load conditions. Notably, MW50 fuel yielded the most consistent reduction in vibration, while SW50 tended to amplify noise at full load. These findings suggest that MWCNTs, particularly at higher concentrations, offer improved vibration mitigation, whereas SWCNTs may enhance noise under certain conditions. The combined use of CNT additives and EGR presents a promising strategy for tuning diesel engine acoustic behavior. KW - Diesel Engine KW - Carbon Nanotube KW - Vibration KW - Noise N2 - Bu çalışmada, karbon nanotüp (CNT) karışımlı yakıtların motor gürültüsü ve titreşim seviyeleri üzerindeki etkileri tek silindirli, hava soğutmalı, doğrudan enjeksiyonlu bir dizel motor kullanılarak deneysel olarak araştırılmıştır. Yakıta tek duvarlı (SWCNT) ve çok duvarlı (MWCNT) karbon nanotüpler 25 ppm ve 50 ppm konsantrasyonlarda eklenmiştir. Testler %0, %25, %50, %75 ve %100 motor yüklerinde, %0, %10 ve %20 egzoz gazı devridaim (EGR) oranlarıyla gerçekleştirilmiştir.Bulgular, motor gürültüsü ve titreşim seviyelerinin genel olarak tüm yakıt tiplerinde motor yükü arttıkça arttığını ortaya koymuştur. Geleneksel dizel yakıtı (D100) için, yük %0'dan %100'e çıktığında gürültü seviyeleri 94,84 dB'den 96,71 dB'ye yükselmiştir. SWCNT karışımlı yakıtlar da gürültü artışları gösterdi; SW25 94,89 dB ile 97,39 dB arasında değişirken, SW50 95,92 dB ile 97,80 dB arasında değişti. MWCNT karışımlı yakıtlar için, MW25 gürültüde 96,68 dB'den 96,49 dB'ye hafif bir düşüş gösterirken, MW50 95,12 dB'den 97,61 dB'ye yükseldi.Titreşim eğilimleri benzer bir örüntüyü izledi. D100 için titreşim seviyeleri 96,23 m/s²'den 96,94 m/s²'ye yükseldi. SW25 89,17 m/s²'den 101,90 m/s²'ye daha keskin bir artış gösterirken, SW50 97,01 m/s²'den 97,34 m/s²'ye hafif bir artış gösterdi. MW25, 100,59 m/s²'den 101,01 m/s²'ye yükselen dalgalı bir eğilim gösterdi, oysa MW50 100,43 m/s²'den 98,28 m/s²'ye düştü.EGR oranını artırmak, özellikle düşük motor yüklerinde, genel olarak gürültü ve titreşim seviyelerini düşürdü, ancak bu etki daha yüksek yüklerde zayıfladı. Genel olarak, SWCNT ve MWCNT karışımlı yakıtlar, D100'e kıyasla yüksek yüklerde gürültü ve titreşim seviyelerini artırdı, MW50 farklı yük koşullarında daha kararlı titreşim davranışı gösterdi. Bu bulgular, CNT katkı maddelerinin ve EGR stratejilerinin dizel motorlarda gürültü ve titreşim özelliklerini optimize etme potansiyelini vurgulamaktadır. CR - Hosseini, S.H., Taghizadeh-Alisaraei, A., Ghobadian, B., Abbaszadeh-Mayvan, A., “Performance and emission characteristics of a CI engine fuelled with carbon nanotubes and diesel-biodiesel blends”, Renewable Energy, 111, 201–213, 2017. https://doi.org/10.1016/j.renene.2017.04.013 CR - Ninawe, G., Tariq, M., “Impact of carbon nanotubes as additives with cotton seed biodiesel blended with diesel in CI engine – An experimental analysis”, Nature Environment and Pollution Technology, 19, 211–219, 2020. CR - Bikkavolu, J.R., Vadapalli, S., Chebattina, K.R.R., Pullagura, G., “Effects of stably dispersed carbon nanotube additives in yellow oleander methyl ester-diesel blend on the performance, combustion, and emission characteristics of a CI engine”, Biofuels, 15, 67–80, 2024. https://doi.org/10.1080/17597269.2023.2216962 CR - Ooi, J.B., Ismail, H.M., Tan, B.T., Wang, X., “Effects of graphite oxide and single-walled carbon nanotubes as diesel additives on the performance, combustion, and emission characteristics of a light-duty diesel engine”, Energy, 161, 70–80, 2018. https://doi.org/10.1016/j.energy.2018.07.062 CR - Chen, A.F., Adzmi, M.A., Adam, A., Othman, M.F., Kamaruzzaman, M.K., Mrwan, A.G., “Combustion characteristics, engine performances and emissions of a diesel engine using nanoparticle-diesel fuel blends with aluminium oxide, carbon nanotubes and silicon oxide”, Energy Conversion and Management, 171, 461–477, 2018. https://doi.org/10.1016/j.enconman.2018.06.004 CR - Bikkavolu, J.R., Vadapalli, S., Chebattina, K.R.R., Pullagura, G., “Effects of stably dispersed carbon nanotube additives in yellow oleander methyl ester-diesel blend on the performance, combustion, and emission characteristics of a CI engine”, Biofuels, 15, 67–80, 2024. https://doi.org/10.1080/17597269.2023.2216962 CR - El-Seesy, A.I., Abdel-Rahman, A.K., Bady, M., Ookawara, S., “Performance, combustion, and emission characteristics of a diesel engine fueled by biodiesel-diesel mixtures with multi-walled carbon nanotubes additives”, Energy Conversion and Management, 135, 373–393, 2017. https://doi.org/10.1016/j.enconman.2016.12.090 CR - Manigandan, S., Atabani, A.E., Ponnusamy, V.K., Pugazhendhi, A., Gunasekar, P., Prakash, S., “Effect of hydrogen and multiwall carbon nanotubes blends on combustion performance and emission of diesel engine using Taguchi approach”, Fuel, 276, 118120, 2020. https://doi.org/10.1016/j.fuel.2020.118120 CR - Özgür, C., Uludamar, E., Soyhan, H.S., Shah, R.M.R.A., “Optimisation of exhaust emissions, vibration, and noise of unmodified diesel engine fuelled with canola biodiesel-diesel blends with natural gas addition by using response surface methodology”, Science and Technology for Energy Transition, 79, 37, 2024. https://doi.org/10.2516/stet/2024031 CR - Gültekin, N., Gülcan, H.E., Ciniviz, M., “The impact of hydrogen injection pressure and timing on exhaust, mechanical vibration, and noise emissions in a CI engine fueled with hydrogen-diesel”, International Journal of Hydrogen Energy, 78, 871–878, 2024. https://doi.org/10.1016/j.ijhydene.2024.06.356 CR - Gültekin, N., “Experimental study of the effects of diesel, bioethanol, and hydrogen on combustion, emissions, mechanical vibration, and noise in a CI engine with different valve lift”, International Journal of Hydrogen Energy, 93, 1011–1021, 2024. https://doi.org/10.1016/j.ijhydene.2024.11.012 CR - Gülcan, H.E., Gültekin, N., Ciniviz, M., “Effect of diesel injection pressure for enhancing combustion and reducing mechanical vibration and noise emissions in a non-road diesel engine”, European Mechanical Science, 7, 199–208, 2023. https://doi.org/10.26701/EMS.1337141 CR - Gültekin, N., Ciniviz, M., “Investigation of the effect of advance angle on performance and emissions (exhaust, vibration, noise) in a single-cylinder diesel engine whose fuel system is converted to common rail”, Environmental Progress & Sustainable Energy, 43, e14261, 2024. https://doi.org/10.1002/ep.14261 CR - Gültekin, N., Numbers, O., “The hydrogen injection strategy’s influence on the performance and emissions (exhaust, vibration, and noise) of a dual-fuel engine”, International Journal of Automotive Engineering and Technologies, 13, 217–229, 2024. https://doi.org/10.18245/ijaet.1553377 CR - Yaşar, A., Keskin, A., Tosun, E., Yıldızhan, Ş., “Catalytic effect of metal based nanoparticles on emission and vibration analysis of diesel engine”, International Journal of Automotive Engineering and Technologies, 9, 113–121, 2020. https://doi.org/10.18245/ijaet.730092 CR - Cellek, F., Arslan, H., “Determination of vibration characteristics on vertical axis of a four cylinder gasoline engine”, International Journal of Automotive Engineering and Technologies, 6, 41–47, 2017. https://doi.org/10.18245/ijaet.308419 CR - Şendur, P., Özcan, M.U., “The modelling and correlation procedure for assessment of vibration performance of a heavy commercial truck”, International Journal of Automotive Engineering and Technologies, 6, 48–60, 2017. https://doi.org/10.18245/ijaet.308420 CR - Nag, S., Sharma, P., Gupta, A., Dhar, A., “Combustion, vibration and noise analysis of hydrogen-diesel dual fuelled engine”, Fuel, 241, 488–494, 2019. https://doi.org/10.1016/j.fuel.2018.12.055 CR - Sharma, N., Patel, C., Tiwari, N., Agarwal, A.K., “Experimental investigations of noise and vibration characteristics of gasoline-methanol blend fuelled gasoline direct injection engine and their relationship with combustion characteristics”, Applied Thermal Engineering, 158, 113754, 2019. https://doi.org/10.1016/j.applthermaleng.2019.113754 CR - Ağbulut, Ü., Karagöz, M., Sarıdemir, S., Öztürk, A., “Impact of various metal-oxide based nanoparticles and biodiesel blends on the combustion, performance, emission, vibration and noise characteristics of a CI engine”, Fuel, 270, 117521, 2020. https://doi.org/10.1016/j.fuel.2020.117521 CR - Adelkhani, A., Nooripour, P., Daneshkhah, E., “The effects of adding TiO₂ and CuO nanoparticles to fuel on engine and hand–arm driver vibrations”, Machines, 12, 724, 2024. https://doi.org/10.3390/machines12100724 CR - Singh, N., Kaushal, R., “Study of modified bio-nano diesel emulsion fuels to save energy, reduce pollution, and improve diesel engine performance”, International Journal of Energy for a Clean Environment, 25, 1–15, 2024. https://doi.org/10.1615/InterJEnerCleanEnv.2023044717 CR - Satsangi, D.P., Tiwari, N., “Experimental investigation on combustion, noise, vibrations, performance and emissions characteristics of diesel/n-butanol blends driven genset engine”, Fuel, 221, 44–60, 2018. https://doi.org/10.1016/j.fuel.2018.02.060 CR - Taghizadeh-Alisaraei, A., Rezaei-Asl, A., “The effect of added ethanol to diesel fuel on performance, vibration, combustion and knocking of a CI engine”, Fuel, 185, 718–733, 2016. https://doi.org/10.1016/j.fuel.2016.08.041 CR - Patel, C., Agarwal, A.K., Tiwari, N., Lee, S., Lee, C.S., Park, S., “Combustion, noise, vibrations and spray characterization for Karanja biodiesel fuelled engine”, Applied Thermal Engineering, 106, 506–517, 2016. https://doi.org/10.1016/j.applthermaleng.2016.06.025 CR - Bowen, C.E., Reader, G.T., Potter, I.J., “Effect of exhaust gas recirculation on the combustion noise level of an indirect injection diesel engine”, Proceedings of the Intersociety Energy Conversion Engineering Conference, 3–4, 2088–2093, 1997. https://doi.org/10.1109/IECEC.1997.656749 CR - Manieniyan, V., Velumani, V., Senthilkumar, R., Sivaprakasam, S., “Effect of EGR (exhaust gas recirculation) in diesel engine with multi-walled carbon nanotubes and vegetable oil refinery waste as biodiesel”, Fuel, 288, 119689, 2021. https://doi.org/10.1016/j.fuel.2020.119689 CR - Kaamierczak, A., Wróbel, R., “The possibility of diagnosis EGR system’s defects by vibration analysis”, Journal of KONES Powertrain and Transport, 15, 2008. CR - Selim, M.Y.E., “A study of some combustion characteristics of dual fuel engine using EGR”, SAE Technical Paper, 2003. https://doi.org/10.4271/2003-01-0766 CR - Selim, M.Y.E., “Effect of exhaust gas recirculation on some combustion characteristics of dual fuel engine”, Energy Conversion and Management, 44, 707–721, 2003. https://doi.org/10.1016/S0196-8904(02)00083-3 CR - Pulluri, G.K., Padal, K.T.B., Sagari, J., “Vibration and noise assessment of a diesel engine fueled with Al₂O₃ nanoparticles dispersed Schleichera oleosa biodiesel”, International Journal of Environmental Science and Technology, 20, 12645–12558, 2023. https://doi.org/10.1007/s13762-022-04652-4 CR - Liu, X., Srna, A., Chan, Q.N., Kook, S., “Effect of exhaust gas recirculation and intake air e-boosting on gasoline compression ignition combustion”, SAE International Journal of Engines, 13, 03-13-03–0025, 2020. https://doi.org/10.4271/03-13-03-0025 CR - Nag, S., Dhar, A., Gupta, A., “Hydrogen-diesel co-combustion characteristics, vibro-acoustics and unregulated emissions in EGR assisted dual fuel engine”, Fuel, 307, 121925, 2022. https://doi.org/10.1016/j.fuel.2021.121925 CR - Sun, W., Wang, X., Guo, L., Zhang, H., Zeng, W., Lin, S., et al., “Study on effects of EGR and injection strategies on the combustion and emission characteristics of ammonia/diesel dual-fuel engine”, Energy, 315, 134391, 2025. https://doi.org/10.1016/j.energy.2025.134391 CR - Gültekin, N., Gülcan, H.E., Ciniviz, M., “The impact of hydrogen injection pressure and timing on exhaust, mechanical vibration, and noise emissions in a CI engine fueled with hydrogen-diesel”, International Journal of Hydrogen Energy, 78, 871–878, 2024. https://doi.org/10.1016/j.ijhydene.2024.06.356 CR - Gültekin, N., “Experimental study of the effects of diesel, bioethanol, and hydrogen on combustion, emissions, mechanical vibration, and noise in a CI engine with different valve lift”, International Journal of Hydrogen Energy, 93, 1011–1021, 2024. https://doi.org/10.1016/j.ijhydene.2024.11.012 CR - Gültekin, N., Ciniviz, M., “Investigation of the effect of advance angle on performance and emissions (exhaust, vibration, noise) in a single-cylinder diesel engine whose fuel system is converted to common rail”, Environmental Progress & Sustainable Energy, 43, e14261, 2024. https://doi.org/10.1002/ep.14261 CR - Sangeetha, M., Boomadevi, P., Khalifa, A.S., Brindhadevi, K., Sekar, M., “Vibration, acoustic and emission characteristics of the chlorella vulgaris microalgae oil in compression ignition engine to mitigate environmental pollution”, Chemosphere, 293, 133475, 2022. https://doi.org/10.1016/j.chemosphere.2021.133475 CR - Hira, A., Debnath, B.K., Chandekar, A.C., “Effects of exhaust gas recirculation on vibration and performance in hydrogen–diesel dual-fuel common rail direct injection engines”, Journal of Thermophysics and Heat Transfer, 1–11, 2025. https://doi.org/10.2514/1.T7139 CR - Gülcan, H.E., Gültekin, N., Ciniviz, M., “Investigation of the effect of camshaft profiles designed with the circular arc curve method for a common rail dual fuel engine on mechanical vibration and noise emissions”, International Journal of Automotive Science and Technology, 7, 269–278, 2023. https://doi.org/10.30939/ijastech..1300577 CR - Kałużny, J., Waligórski, M., Szymański, G.M., Merkisz, J., Różański, J., Nowicki, M., et al., “Reducing friction and engine vibrations with trace amounts of carbon nanotubes in the lubricating oil”, Tribology International, 151, 106484, 2020. https://doi.org/10.1016/j.triboint.2020.106484 UR - https://doi.org/10.18245/ijaet.1651115 L1 - https://dergipark.org.tr/tr/download/article-file/4660257 ER -