TY  - JOUR
T1  - Al-Si3N4 Toz Metal Kompozit Malzeme Üretimi ve Aşınma Davranışının Araştırılması
AU  - Arık, Halil
PY  - 2019
DA  - December
DO  - 10.29109/gujsc.621116
JF  - Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
JO  - GUJS Part C
PB  - Gazi Üniversitesi
WT  - DergiPark
SN  - 2147-9526
SP  - 776
EP  - 787
VL  - 7
IS  - 4
LA  - tr
AB  - ÖzetAlüminyum ve alaşımları başta otomotiv vehavacılık sektörü olmak üzere pek çok alanda tercih edilen metal ve alaşımgrubunu oluşturmaktadır. Alüminyumalaşımlarının üstün özellikleri yanında sertlik ve aşınma direnci gibiözelliklerinin bazı uygulamalarda beklentilerin uzağında kalması alüminyummatrisli kompozit malzeme üretimi çalışmalarını daha değerli ve gereklikılmaktadır. Bu çalışmada toz metalürjisi metodu ile üretilen α-Si3N4içeren alüminyum matrisli kompozit malzemelerde takviye elemanı oranınınkompozitin aşınma davranışı üzerine etkilerinin belirlenmesi amaçlanmıştır.Ağırlıkça %5, %10 ve %15 oranlarında α-Si3N4 içerenkarışım tozlar kalıp içerisinde 500 MPa basınç altında preslenerek 10 mm çaptave 15 mm boyda blok numuneler üretilmiştir. Daha sonra preslenen numuneleratmosfer kontrollü tüp fırında 2 saat süreyle 650 °C sıcaklıktasinterlenmiştir. Toz metal kompozit parçaların yoğunluk ve sertlik ölçümleri sonrasıpin-on-disk metoduyla kuru kayma aşınma testleri yapılmıştır. TestlerTIRIBOMETER T10/20 aşındırma test cihazında ASTM G99-05’ göre yapılmıştır.Aşındırma testleri 1,41 m/s kayma hızı ve 2000 m mesafede farklı yükler(5-10-15 N) altında tekrarlanmıştır. Alınan aşınma test sonuçları aynışartlarda üretilen matris malzemeye göre değişik oranlarda α-Si3N4takviyeli kompozitlerin daha iyi aşınma direncinde sahip olduğunugöstermektedir. En yüksek aşınma direnci ve sertlik değerleri ağırlıkça % 15silisyum nitrür içeren kompozit malzemede görülmüştür.
KW  - Toz Metalurjisi
KW  - Kompozit Malzeme
KW  - Al-Si3N4
KW  - Aşınma Davranışı
CR  - KAYNAKLAR (REFERENCES)
CR  - [1] Rosso M. 2006, Ceramic and Metal Matrix Composites: Routes and Properties, Journal of Materials Processing Technology, 175: 364-375.
CR  - [2] Sahu P.S., Banchhor R., 2017. Effect of Different Reinforcement on Mechanical Properties of Aluminium Metal Matrix Composites, Res. J. Engineering Sci., Vol. 6 (7), 39-45.
CR  - [3] Mattli M.R., Matli R.R et all. 2019. Structural and Mechanical Properties of Amorphous Si3N4 Nanoparticles Reinforced Al Matrix Composites Prepared by Microwave Sintering, Ceramics, 2: 126–134.
CR  - [4] Mahajan G.V., Aher V.S. 2012. Composite Material: A Review over Current Development and Automotive Application, International Journal of Scientific and Research Publications, 2 (11), 1-5.
CR  - [5] Babalola P.O.,Bolu C.A., et all. 2014. Development of Aluminium Matrix Composites: A Review, Journal of Engineering and Technology Research, l (2), 1-11.[6] Ervina Efzan M.N., Siti Syazwani N., and Abdullah M.M.A.B. 2016. Fabrication Method of Aluminum Matrix Composite (Amcs): A Review, Key Engineering Materials, 700, 02-110.[7] Ramnath B.V., Elanchezhian  C. 2014. Alumınıum Metal Matrıx Composıtes - A Revıew, Advanced Materials Science, 38: 55-60.[8] Manohar G.,  Dey A., Pandey K.M. and Maity S.R., 2019. Fabrication of metal matrix composites by powder metallurgy: A review, International Conference on Electrical, Electronics, Materials and Applied Science,  020041-1-8.[9] Thirumoorthy A,  Arjunan T.V., Senthil Kumar K.L. 2018. Latest Research Development in Aluminum Matrix with Particulate Reinforcement Composites – A Review, Materials Today: Proceedings 5, 1657–1665.[10] Attar S., Nagaral M., et all. 2015. A Review on Particulate Reinforced Aluminum Metal Matrix Composites, Journal of Emerging Technologies and Innovative Research, 2 (2), 225-229.
CR  - [11] Bedir F., 2007. Characteristic properties of Al–Cu–SiCp and Al–Cu–B4Cp Composites Produced by Hot Pressing Method Under Nitrogen Atmosphere, Materials and Design, 28:1238-1244
CR  - [12] Kırmızı G., Arık H., Çinici H. 2019. Experimental Study on Mechanical and Ballistic Behaviours of Silicon Carbide Reinforced Functionally Graded Aluminum Foam Composites. Composites Part B, 164: 345-357.
CR  - [13] O’Donnell G., Looney L., 2001.  Production of aluminium matrix composite components using conventional PM technology, Materials Science and Engineering A 303: 292-301.
CR  - [14] Kaczmar J.W., Pietrzak K., Wøosinski W., 2000.  The Production and Application of Metal Matrix Composite Materials, Journal of Materials Processing Technology, 106: 58-67.
CR  - [15] Mahdavi S., Akhlaghi FR. 2011. Effect of the SiC Particle Size on The Dry Sliding Wear Behavior of Sic And SiC–Gr-Reinforced Al6061 Composites, J Mater Sci, 46:7883-7894.
CR  - [16] Sureshkumar P., Uvaraja V. 2018. Effect of Ceramic and Metallic Reinforcement on  Mechanical, Corrosion, and Tribological Behavior of Aluminum Composite by Adopting Design of Experiment Through Taguchi Technique, 140: 1-11.
CR  - [17] Kumar M., Gupta R.K., Pandey A.  2018. A Review on Fabrication and Characteristics of Metal Matrix Composites Fabricated by Stir Casting, Conference Series: Materials Science and Engineering 377: 1-9.[18] Saravanan R., Vinod K., Tamilarasan T., 2015. Investıgatıon of Wear Behavıour of Al 6061 Alloy Reınforced Wıth SiC, Al2O3 and  E Glass Fıber, International Journal of Scientific Engineering and Applied Science (IJSEAS),1(5), 430-434.
CR  - [19] Imran M., Anwar Khan A.R. 2019. Characterization of Al-7075 Metal Matrix Composites: A Review, J. Materials Research and Technology, 8(3): 3347–3356.[20] Ramesh B.T. 2014. Characterization of Al Based Nano composites Using Powder Metallurgy Technique, Internatıonal Journal of Research In Aeronautıcal and Mechanıcal Engıneerıng, Vol: 2, Issue 2, 131-147.
CR  - [21] William C., Harrigan Jr. Commercial Processing of Metal Matrix Composites, Materials Science and Engineering A, 244: 75-79.
CR  - [22] Ambigai R., Prabhu S. 2017. Optimization of Friction and Wear Behaviour of Al-Si3N4 Nano Composite and Al-Gr-Si3N4 Hybrid Composite Under Dry Sliding Conditions, Trans. Nonferrous Met. Soc. China 27, 986-997.
CR  - [23] Ul Haq M.I., Anand A. 2018. Dry Sliding Friction and Wear Behaviour of Hybrid    AA7075/Si3N4/Gr Self Lubricating Composites, Mater. Res. Express, (5), 1-12.
CR  - [24] Sharma P., Sharma S., and Khanduja D. 2017. Production and Characterization of AA6082-(Si3N4 + Gr) Stir Cast Hybrid Composites, Partıculate Scıence and Technology, 35 (2), 158-165.
CR  - [25] Monikandan V.V., Joseph M.A., Rajendrakumar P.K. 2016.  Dry Sliding Wear Studies of Aluminum Matrix Hybrid Composites, Resource-Efficient Technologies 2, 12–S24.
CR  - [26] Ambigai R., Prabhu S. 2019. Fuzzy Logic Algorithm Based Optimization of The Tribological Behavior of Al-Gr-Si3N4 Hybrid Composite, Measurement, 146: 736–748.
CR  - [27] Tyagi A., Sharma D. 2018. Characterization of AA6082/Si3N4 Composites, 1st International Conference on New Frontiers in Engineering, Science & Technology, New Delhi, India, January 8-12.
CR  - [28] Sharma P., Sharma S., Khanduja D. 2015. Production and Some Properties of Si3N4 Reinforced Aluminium Alloy Composites, Journal of Asian Ceramic Societies 3, 352–359.
CR  - [29] Arık H., Semerci P., Kırmızı G. 2017. Sıcak Presleme ile Alüminyum Matrisli ve Al2O3 Takviyeli Toz Metal Kompozit Malzeme Üretimi ve Aşınma Davranışının Araştırılması, GU J Sci, Part C, 5(4): 87-97.
CR  - [30] Arik H., Orhun D.Z., 2018. Investigation of Dry Sliding Wear Behavior of Powder Metal (P/M) Materials Produced from Mixture of Fe-Cu-C Powders, GU J Sci, Part A, 5: 37-48.
CR  - [31] Arik H. 2008. Effect of Mechanical Alloying Process on Mechanical Properties of -Si3N4 Reinforced Aluminum-Based Composite Materials. Materials & Design, 29: 1865-1861.
CR  - [32] Ramesh B. T., Arun Kumar M. B., Swamy R.P.  2015.  Dry Sliding Wear Test Conducted On Pin-On-Disk Testing Setup For Al6061-SiC Metal Matrix Composites Fabricated by Powder Metallurgy, International Journal of Innovative Science, Engineering & Technology, 2(6), 264-270.
CR  - [33] Lawrence O.O., Oluwaseyi O. T., and Samson O. A. 2017. The Dry Sliding Wear Behaviour of Aluminum Composites: A Review, The West Indian Journal of Engineering, 40(1), 17-23.
CR  - [34] Veeresh Kumar G.B., Rao C.S.P., Selvaraj N. 2012. Studies on Mechanical and Dry Sliding Wear of Al6061–SiC Composites, Composites: Part B, 43: 1185–1191.
CR  - [35] Rao R.N., Das S. 2010. Effect of Matrix Alloy and Influence of SiC Particle on the Sliding Wear Characteristics of Aluminium Alloy Composites, Materials and Design 31. 1200-1207.
CR  - [36] Ul Haq M.I., Anand A. 2018. Dry Sliding Friction and Wear Behavior of AA7075-Si3N4 Composite, Silicon, 10:1819-1829.
CR  - [37] Radhika N., Raghu R. 2015.  Parametrıc Study of Dry Slıdıng Wear Behavıour of Functıonally Graded Al LM25/Si3N4 Composıte by Response Surface Methodology, Advanced Composites Letter, 24, (6), 130-136.
UR  - https://doi.org/10.29109/gujsc.621116
L1  - https://dergipark.org.tr/tr/download/article-file/878478
ER  -