Araştırma Makalesi
BibTex RIS Kaynak Göster
Yıl 2019, , 8 - 10, 28.06.2019
https://doi.org/10.17678/beuscitech.433028

Öz

Kaynakça

  • 1. Bell, A., Ayoub, A.F., Siebert, P.: Assessment of the accuracy of a three-dimensional imaging system for archiving dental study models. J. Orthod. 30, 219–223 (2003)
  • 2. Quimby, M.L., Vig, K.W.L., Rashid, R.G., Firestone, A.R.: The accuracy and reliability of measurements made on computer-based digital models. Angle Orthod. 74, 298–303 (2004)
  • 3. 3B da basılan küçük azı dişin uygulama videoları
  • 4. Garino, F., Garino, G.B.: Comparison of dental archmeasurements between stone and digital dental casts. World J. Orthod. 3, 250– 254 (2002) 5. Martinez, E. H. V., Can, Emre. (2016). Bilgisayar Destekli Seramik Üretim Yöntemi Olarak Üç Boyutlu Yazıcılar ve Günümüz Koşullarında Uygulama Örneği. Anadolu Üniversitesi Sanat & Tasarım Dergisi, 6(1),1-15.
  • 6. Davendorf, L. , Ryokai, K. “Beingthe Machine: ReconfiguringAgencyand Control in HybridFabrication” Digital&MaterialsFabrication, CHI 2015, Crossings, Seoul, Korea.
  • 6. Life of 3D Printer, Power point demo, Karabuk University,Department of Endustrıal Design Engineering-2015
  • 7. https://www.youtube.com/watch?v=XLaeOQa0APw

An Examination of 3D Printing in Dentistry - A Study

Yıl 2019, , 8 - 10, 28.06.2019
https://doi.org/10.17678/beuscitech.433028

Öz



This study examines the design
and production processes of a small molar tooth produced with a 3D printer.
When designing the exercises, polygons and parabolic forms were used as output
points. These forms, which are rendered in three dimensions in the computer
environment, are formed taking into consideration the structural
characteristics of the production material. PLA (
Polylactic Acid )
material is used in this design which is produced in three dimensional printer
by FDM (Fused Deposition Modeling)  method. In the scope of the study, the
conditions experienced in the design of the material used were mentioned and
the material mistake was given during printing. The different effects of the
commands used in the design process on the production surfaces, as well as
voluntary or involuntary faults, are very important in the formation of some
deformations and are caused by the plastic nature of the material. In addition,
the effects of PLA on the surface of the faults are investigated. However,
different methods applied in the production of sole parts and surfaces have
been evaluated.

Kaynakça

  • 1. Bell, A., Ayoub, A.F., Siebert, P.: Assessment of the accuracy of a three-dimensional imaging system for archiving dental study models. J. Orthod. 30, 219–223 (2003)
  • 2. Quimby, M.L., Vig, K.W.L., Rashid, R.G., Firestone, A.R.: The accuracy and reliability of measurements made on computer-based digital models. Angle Orthod. 74, 298–303 (2004)
  • 3. 3B da basılan küçük azı dişin uygulama videoları
  • 4. Garino, F., Garino, G.B.: Comparison of dental archmeasurements between stone and digital dental casts. World J. Orthod. 3, 250– 254 (2002) 5. Martinez, E. H. V., Can, Emre. (2016). Bilgisayar Destekli Seramik Üretim Yöntemi Olarak Üç Boyutlu Yazıcılar ve Günümüz Koşullarında Uygulama Örneği. Anadolu Üniversitesi Sanat & Tasarım Dergisi, 6(1),1-15.
  • 6. Davendorf, L. , Ryokai, K. “Beingthe Machine: ReconfiguringAgencyand Control in HybridFabrication” Digital&MaterialsFabrication, CHI 2015, Crossings, Seoul, Korea.
  • 6. Life of 3D Printer, Power point demo, Karabuk University,Department of Endustrıal Design Engineering-2015
  • 7. https://www.youtube.com/watch?v=XLaeOQa0APw
Toplam 7 adet kaynakça vardır.

Ayrıntılar

Birincil Dil İngilizce
Bölüm Makaleler
Yazarlar

Bekir Cirak

Yayımlanma Tarihi 28 Haziran 2019
Gönderilme Tarihi 11 Haziran 2018
Yayımlandığı Sayı Yıl 2019

Kaynak Göster

IEEE B. Cirak, “An Examination of 3D Printing in Dentistry - A Study”, Bitlis Eren University Journal of Science and Technology, c. 9, sy. 1, ss. 8–10, 2019, doi: 10.17678/beuscitech.433028.