Superfinishing Process of Ball Bearings

Year 2024, Volume: 21 Issue: 2, 63 - 70, 01.11.2024

İrem Gül Aslanbaş , Samad Nadimi Bavil Olıaeı

https://izlik.org/JA63ZB85LJ

Abstract

Superfinishing is one of the most crucial machining process stage in the production of ball bearings. This process determines the quality, form, and geometry of ball bearing raceway. The factors influencing the performance of the superfinishing process are not only processing parameters but also the characteristics of the superfinishing stone used. In this study, experiments with different material components and chemical compositions of stones were conducted to achieve the desired surface topography, specifically on the inner raceway of a 6206-type bearing. In experiments using four different superfinishing stones, Ra and Rz measurements were taken to evaluate the performance of the stones. As a result of the experiments, it was observed that the White Alumina stone provided the best Ra results in these process parameters.

Keywords

Superfinishing , Ball Bearings , Surface , Ra , Rz

Ethical Statement

Bu çalışmanın, özgün bir çalışma olduğunu; çalışmanın hazırlık, veri toplama, analiz ve bilgilerin sunumu olmak üzere tüm aşamalarından bilimsel etik ilke ve kurallarına uygun davrandığımı; bu çalışma kapsamında elde edilmeyen tüm veri ve bilgiler için kaynak gösterdiğimi ve bu kaynaklara kaynakçada yer verdiğimi; kullanılan verilerde herhangi bir değişiklik yapmadığımı, çalışmanın Committee on Publication Ethics (COPE)' in tüm şartlarını ve koşullarını kabul ederek etik görev ve sorumluluklara riayet ettiğimi beyan ederim. Herhangi bir zamanda, çalışmayla ilgili yaptığım bu beyana aykırı bir durumun saptanması durumunda, ortaya çıkacak tüm ahlaki ve hukuki sonuçlara razı olduğumu bildiririm.

Thanks

Bu makalenin hazırlanmasında desteğini esirgemeyen Yiğit Karpat'a teşekkür ederiz. Yine tezgah ve parça ile destekleyen Ortadoğu Rulman Sanayi Tic.A.Ş 'ye teşekkür ederiz.

References

• F. Hashimoto, H. Yamaguchi, P. Krajnik, K. Wegener, R. Chaudhari, H. W. Hoffmeister, and F. Kuster, “Abrasive Fine-Finishing Technology,” CIRP Ann Manuf Technol, vol. 65, no. 2, pp. 597–620, Oct. 2016, doi: 10.1016/j.cirp.2016.06.003.
• S. Malkin and B. Varghese, “Experimental Investigation of Methods to Enhance Stock Removal for Superfinishing,” CIRP Annals, vol. 47, no. 1, pp. 231-234, Jan. 1998.
• W. Grzesik, J. Rech, and T. Wanat, “Surface Finish on Hardened Bearing Steel Parts Produced By Superhard and Abrasive Tools,” Int J Mach Tools Manuf, vol. 47, no. 2, pp. 255–262, Feb. 2007, doi: 10.1016/j.ijmachtools.2006.03.018.
• P. Knight, “Enhanced Surface Finishing of Bearing Raceways,’’ Ph.D. Thesis, School of Indus and Manuf Sci, Cranfield University, United Kingdom, 2000.
• E. Uhlmann, G. Spur, and M. Kleinschnitker, “Honing and Superfinishing,” in Handbook of Ceramics Grinding and Polishing, I. D. Marinescu, T. K. Doi and E. Uhlmann, Eds. Elsevier, pp. 234–262, 2015.
• Y. Onchi, N. Matsumori, N. Ikawa, and S. Shimada, “Porous Fine CBN Stones for High Removal Rate Superfinishing,” CIRP Ann Manuf Technol, vol. 44, no. 1, pp. 291–294, 1995, doi: 10.1016/S0007-8506(07)623282.
• R. Leach, Editor, “Characterization of Areal Surface Texture,” Springer, 2013, doi: 10.1007/978-3-642-36458-7.
• S. Neagu-Ventzel, S. Cioc, and I. Marinescu, “A Wear Model and Simulation of Superfinishing Process: Analysis for The Superfinishing of Bearing Rings,’’ Wear, vol. 260, no. 9–10, pp. 1061–1069, 2006, doi: 10.1016/j.wear.2005.07.024.
• T. Enomoto, U. Satake, and X. Mao, “New Water-Based Fluids as Alternatives to Oil-Based Fluids in Superfinishing Processes,” CIRP Annals, vol. 69, no. 1, pp. 297-300, Dec.2020, doi: 10.1016/j.cirp.2020.04.106.