Estimation of three-point bending behavior using finite element method for 3D-printed polymeric sandwich structures with honeycomb and reentrant core

Abstract

Sandwich structures are known as ultra-light porous materials. Because the structure has advantages in terms of acoustics, fatigue, and impact resistance that conventional stiffened plates cannot match, it has become a popular material in aerospace, automotive, marine, windmill, and architectural applications. One promising method for decreasing production waste and enhancing flexural stress is to employ Additive Manufacture (AM) technologies for sandwich structure manufacturing. In this study, polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), and polyethylene terephthalate glycol (PETG) sandwich structures with reentrant and honeycomb cores were designed and then a finite element analysis (FEA) was carried out to compare the stress distributions in these sandwich composites. According to the findings, higher flexure stresses and specific energy absorption were obtained in the reentrant sandwich structures compared to honeycomb sandwich structures. A minimum equivalent stress value was found in the ABS material, while a maximum equivalent stress value was found in the PLA material.

Keywords

• Sandwich Structures
• 3D printing
• Finite Element Analysis
• Three-point Bending

References

1. Xie, S., Feng, Z., Zhou, H., & Wang, D. (2021). Three-point bending behavior of Nomex honeycomb sandwich panels: Experiment and simulation. Mechanics of Advanced Materials and Structures, 28(18): 1917-1931, DOI:10.1080/15376494.2020.1712751
2. Sarvestani, H. Y., Akbarzadeh, A. H., Mirbolghasemi, A., & Hermenean, K. (2018). 3D printed meta-sandwich structures: Failure mechanism, energy absorption and multi-hit capability. Materials & Design, 160: 179-193, DOI:10.1016/j.matdes.2018.08.061
3. Pollard, D., Ward, C., Herrmann, G., & Etches, J. (2017). The manufacture of honeycomb cores using Fused Deposition Modeling. Advanced Manufacturing: Polymer & Composites Science, 3(1): 21-31, DOI:10.1080/20550340.2017.1306337
4. de Castro, B. D., Magalhães, F. D. C., Panzera, T. H., & Campos Rubio, J. C. (2021). An assessment of fully integrated polymer sandwich structures designed by additive manufacturing. Journal of Materials Engineering and Performance, 30(7): 5031-5038, DOI:10.1007/s11665-021-05604-8
5. Qi, C., Remennikov, A., Pei, L. Z., Yang, S., Yu, Z. H., & Ngo, T. D. (2017). Impact and close-in blast response of auxetic honeycomb-cored sandwich panels: experimental tests and numerical simulations. Composite structures, 180: 161-178, DOI: 10.1016/j.compstruct.2017.08.020
6. Zaharia, S. M., Enescu, L. A., & Pop, M. A. (2020). Mechanical performances of lightweight sandwich structures produced by material extrusion-based additive manufacturing. Polymers, 12(8): 1740, DOI: 10.3390/polym12081740
7. Ingrole, A., Hao, A., & Liang, R. (2017). Design and modeling of auxetic and hybrid honeycomb structures for in-plane property enhancement. Materials & Design, 117: 72-83, DOI:10.1016/j.matdes.2016.12.067
8. Li, T., & Wang, L. (2017). Bending behavior of sandwich composite structures with tunable 3D-printed core materials. Composite Structures, 175: 46-57, DOI:10.1016/j.compstruct.2017.05.001

9. Essassi, K., Rebiere, J. L., El Mahi, A., Souf, M. A. B., Bouguecha, A., & Haddar, M. (2020). Experimental and analytical investigation of the bending behaviour of 3D-printed bio-based sandwich structures composites with auxetic core under cyclic fatigue tests. Composites Part A: Applied Science and Manufacturing, 131: 105775, DOI:10.1016/j.compositesa.2020.105775
10. Yang, S., Qi, C., Guo, D. M., & Wang, D. (2012). Energy absorption of an re-entrant honeycombs with negative Poisson’s ratio. In Applied Mechanics and Materials (Vol. 148, pp. 992-995). Trans Tech Publications Ltd., DOI:10.4028/www.scientific.net/AMM.148-149.992
11. Najafi, M., Ahmadi, H., & Liaghat, G. (2022). Investigation on the flexural properties of sandwich beams with auxetic core. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 44(2):1-11, DOI:10.1007/s40430-022-03368-3
12. Gohar, S., Hussain, G., Ali, A., & Ahmad, H. (2021). Mechanical performance of honeycomb sandwich structures built by FDM printing technique. Journal of Thermoplastic Composite Materials, 0892705721997892, DOI: 10.1177/0892705721997892
13. Serjouei, A., Yousefi, A., Jenaki, A., Bodaghi, M., & Mehrpouya, M. (2022). 4D printed shape memory sandwich structures: Experimental analysis and numerical modeling. Smart Materials and Structures, 31: 055014, DOI: 10.1088/1361-665X/ac60b5
14. Sugiyama, K., Matsuzaki, R., Ueda, M., Todoroki, A., & Hirano, Y. (2018). 3D printing of composite sandwich structures using continuous carbon fiber and fiber tension. Composites Part A: Applied Science and Manufacturing, 113: 114-121, DOI: 10.1016/j.compositesa.2018.07.029