Investigation of electrochemical oxidation process time and glycidoxypropyl trimethoxy silane coating in glass fiber reinforced composite adhesive bonded joints

İclal Avinç Akpınar

doi:10.26701/ems.1702654

Investigation of electrochemical oxidation process time and glycidoxypropyl trimethoxy silane coating in glass fiber reinforced composite adhesive bonded joints

Abstract

In this study, the effects of the electrochemical oxidation treatment duration and the coating with glycidoxypropyltrimethoxysilane (GPTMS) on the bond strength of aluminum joints bonded with glass fiber-reinforced adhesive were investigated. Glass fibers were subjected to electrochemical oxidation in a sulfuric acid solution for 3, 6, and 9 minutes, then chopped into lengths of approximately 10 mm before being incorporated into the adhesive. The surfaces of the bonded aluminum materials were prepared by chemical etching, and single-lap joints were fabricated using the fiber-reinforced adhesive. The fabricated joints were subjected to three-point bending tests, and the failure loads were determined. Additionally, GPTMS coating was applied to the surfaces of oxidized glass fibers, and joints were similarly fabricated and tested. The results demonstrated that the oxidation treatment of the glass fibers improved the bond strength, and that this improvement was dependent on the oxidation duration. Furthermore, it was found that the silane coating process enhanced the joint performance by approximately 10–13% after the oxidation treatment. In addition, the obtained results were supported by contact angle measurements and scanning electron microscopy (SEM) analysis. This study highlights the effect of glass fiber surface modification on adhesive bonding performance.

Keywords

Supporting Institution

Erzurum Technical University Scientific Research Project

Project Number

Project No: 2025/002

References

Çalık, A. (2008). Yapıştırıcılar ve köşeleri yuvarlatılmış basamaklı bindirme yapıştırıcı bağlantılarda gerilme analizi \[Yüksek lisans tezi, Zonguldak Karaelmas Üniversitesi].
Hadjez, F., & Necib, B. (2018). Experimental characterization and numerical modelling analyses of nano-adhesive-bonded joints. Frattura ed Integrità Strutturale, 12, 94–105. https://doi.org/10.3221/IGF-ESIS.48.10
Reza Borghei, R. H., Behjat, B., & Yazdani, M. (2019). The impact of graphene nanoparticle additives on the strength of simple and hybrid adhesively bonded joints. Journal of Composite Materials, 53, 3335–3346. https://doi.org/10.1177/0021998319845837
Razavi, S. M. J., Ayatollahi, M., Nemati Giv, R. A., & Khoramishad, H. (2018). Single lap joints bonded with structural adhesives reinforced with a mixture of silica nanoparticles and multi walled carbon nanotubes. International Journal of Adhesion and Adhesives, 80, 76–86. https://doi.org/10.1016/j.ijadhadh.2017.10.004
Kang, M. H., Choi, J. H., & Kweon, J. H. (2014). Fatigue life evaluation and crack detection of the adhesive joint with carbon nanotubes. Composite Structures, 108, 417–422. https://doi.org/10.1016/j.compstruct.2013.09.048
Marami, G., Nazari, S. A., Faghidian, S. A., & Tahami, F. V. (2016). Improving the mechanical behavior of the adhesively bonded joints using RGO additive. International Journal of Adhesion and Adhesives, 70, 277–286. https://doi.org/10.1016/j.ijadhadh.2016.08.006
Li, Y., Li, C., He, J., Gao, Y., & Hu, Z. (2020). Effect of functionalized nano-SiO2 addition on bond behavior of adhesively bonded CFRP-steel double-lap joint. Construction and Building Materials, 244, Article 118400. https://doi.org/10.1016/j.conbuildmat.2020.118400
Simaafrookhteh, S., Tsokanas, P., Loutas, T., Lomov, S. V., & Ivens, J. (2024). Measuring the interlaminar fracture toughness of thin carbon fiber/Polyamide6 composites using adhesively bonded stiffeners. Composites Part A: Applied Science and Manufacturing, 176, 107841. https://doi.org/10.1016/j.compositesa.2023.107841

Mrzljak, S., Zanghellini, B., Gerdes, L., Helwing, R., Schuller, R., Sinn, G., & Rennhofer, H. (2023). Effect of carbon nanofibre orientation on fatigue properties of carbon fibre-reinforced polymers. Journal of Composite Materials, 57(6), 1149–1164. https://doi.org/10.1177/00219983221136053
Thirunavukarasu, R. S., & Sikarwar, B. S. (2024). Enhancing the strength of adhesively bonded single-lap composite joints using fiber fabrics. Materials Letters, 356, 135664. https://doi.org/10.1016/j.matlet.2023.135664
Thirunavukarasu, R. S., & Sikarwar, B. S. (2024). Influence of meshes on mechanical performance and stiffness of single-lap adhesive bonded composite joints. Materials Letters, 367, 136587. https://doi.org/10.1016/j.matlet.2024.136587
Xiao, J., Tian, S. Y., Zhou, H., Wang, Y., & Xu, L. H. (2024). Andic oxidation of high-modulus carbon fibers in sulfuric acid under different electric fields. Cailiao Gongcheng - Journal of Materials Engineering, 52(6), 122–131.
Chen, X., Wen, K., Wang, C., Cheng, S., Wang, S., Ma, H., & Shao, J. (2022). Enhancing mechanical strength of carbon fiber-epoxy interface through electrowetting of fiber surface. Composites Part B: Engineering, 234, 109751. https://doi.org/10.1016/j.compositesb.2021.109751
Avinc Akpinar, I. (2024). The effect of chemical etching and nanostructure additive epoxy coating technique on adhesion strength in aluminum joints bonded with nanostructure additive adhesive. International Journal of Adhesion and Adhesives, 129, 103584. https://doi.org/10.1016/j.ijadhadh.2023.103584
Andideh, M., & Esfandeh, M. (2017). Effect of surface modification of electrochemically oxidized carbon fibers by grafting hydroxyl and amine functionalized hyperbranched polyurethanes on interlaminar shear strength of epoxy composites. Carbon, 123, 233–242. https://doi.org/10.1016/j.carbon.2017.07.014
Avinc Akpinar, I. (2025). A study on the effects of electrochemical oxidation and silane modification applied to fibers in short carbon fiber-reinforced structural adhesives and adhesive joints. International Journal of Adhesion and Adhesives, 140, 104020. https://doi.org/10.1016/j.ijadhadh.2024.104020
17. Wen, Z., Xu, C., Qian, X., Zhang, Y., Wang, X., Song, S., Dai, M., & Zhang, C. (2019). A two-step carbon fiber surface treatment and its effect on the interfacial properties of CF/EP composites: The electrochemical oxidation followed by grafting of silane coupling agent. Applied Surface Science, 486, 546–554. https://doi.org/10.1016/j.apsusc.2019.05.016
Yuan, X., Zhu, B., Cai, X., Qiao, K., Zhao, S., & Yu, J. (2018). Influence of different surface treatments on the interfacial adhesion of graphene oxide/carbon fiber/epoxy composites. Applied Surface Science, 458, 996–1005. https://doi.org/10.1016/j.apsusc.2018.07.055
Akpinar, S., & Avinc Akpinar, I. (2023). Influence of carbon and glass fiber reinforced composite adhesive on the strength of adhesively bonded joints. Materials Testing, 65(5), 802–814. https://doi.org/10.1515/mattest-2022-0300
Deshmukh, R. R., & Bhat, N. V. (2003). The mechanism of adhesion and printability of plasma processed PET films. Materials Research Innovations, 7, 283–290. https://doi.org/10.1007/s10019-003-0234-0
Avinc Akpinar, I., Gürses, A., Akpinar, S., Gultekin, K., Akbulut, H., & Ozel, A. (2018). Investigation of mechanical and thermal properties of nanostructure-doped bulk nanocomposite adhesives. The Journal of Adhesion, 94, 847–866. https://doi.org/10.1080/00218464.2017.1313491
Baldan, A. (2012). Adhesion phenomena in bonded joints. International Journal of Adhesion and Adhesives, 38, 95–116. https://doi.org/10.1016/j.ijadhadh.2012.04.007
ISO. (1992). ISO 10365:1992(E), Adhesives—Designation of main failure patterns. International Organization for Standardization.

Details

Primary Language

English

Subjects

Nanomaterials

Journal Section

Research Article

Authors

İclal Avinç Akpınar ^*
0000-0001-9994-6733
Türkiye

Publication Date

September 20, 2025

Submission Date

May 20, 2025

Acceptance Date

July 18, 2025

Published in Issue

Year 1970 Volume: 9 Number: 3

DOI

https://doi.org/10.26701/ems.1702654

IZ

https://izlik.org/JA65JM37LE

Cite

RIS / Bibtex

APA

Avinç Akpınar, İ. (2025). Investigation of electrochemical oxidation process time and glycidoxypropyl trimethoxy silane coating in glass fiber reinforced composite adhesive bonded joints. European Mechanical Science, 9(3), 221-233. https://doi.org/10.26701/ems.1702654