Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures

Mehmet Kopar

doi:10.64808/engineeringperspective.1861151

Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures

Abstract

Additive manufacturing technologies enable the fabrication of crash boxes that are difficult to produce using conventional manufacturing methods. In this study, the crashworthiness performance of multi-cell crash boxes reinforced with face-centered cubic lattice structures, manufactured from PLA+ and ABS+ thermoplastic materials using the fused deposition modeling method, was investigated experimentally and numerically. Quasi-static axial compression tests were conducted to determine the crushing behavior of the structures, and the experimental results were validated using the finite element method. Experimental findings revealed that polymer-based lattice structures significantly enhanced the energy absorption performance of multi-cell crash boxes. Compared to unreinforced configurations, the total energy absorption increased by approximately 79% for PLA+ crash boxes reinforced with lattice structures, while an increase of approximately 100% was observed for ABS+ crash boxes. In PLA+ crash boxes, a limited increase of approximately 1.5% in peak crushing force was achieved due to lattice reinforcement. In contrast, lattice-reinforced ABS+ crash boxes exhibited an increase of approximately 30% in peak crushing force, indicating that ductile polymers are more effectively supported by internal lattice structures. Furthermore, the mean crushing force increased by approximately 80% for PLA+ crash boxes and 99% for ABS+ crash boxes because of lattice reinforcement. Despite the increase in structural mass caused by the lattice structures, the specific energy absorption improved by approximately 4% for PLA+ crash boxes and 9% for ABS+ crash boxes. A good agreement was observed between experimental and numerical results in terms of force- displacement responses and deformation modes. The obtained findings demonstrate that multi-cell polymer crash boxes reinforced with face-centered cubic lattice structures possess significant potential as lightweight and high efficiency energy absorbing components for automotive applications.

Keywords

References

1. Van Ratingen, M. R. (2022). Consumer ratings and their role in improving vehicle safety. In The Vision Zero Handbook: Theory, Technology and Management for a Zero Casualty Policy (pp. 755-788). Cham: Springer International Publishing https://doi.org/10.1007/978-3-030-76505-7_30
2. Singh, G., Singh, J., Singh, N., Farina, I., Colangelo, F., & Pandey, P. M. (2024). Effect of unit cell shape and structure volume fraction on the mechanical and vibration properties of 3D printed lattice structures. Journal of Thermoplastic Composite Materials, 37(5), 1841–1858. https://doi.org/10.1177/08927057231203156
3. Xie, C., Wang, D., Zong, L., Wang, S., & Kong, D. (2023). Multi-objective crashworthiness optimization of energy-absorbing box with gradient lattice structure. Applied Mathematical Modelling, 121, 304–320. https://doi.org/10.1016/j.apm.2023.05.001
4. Hou, W., He, P., Yang, Y., & Sang, L. (2023). Crashworthiness optimization of crash box with 3D-printed lattice structures. International Journal of Mechanical Sciences, 247, 108198. https://doi.org/10.1016/j.ijmecsci.2023.108198
5. Simpson, J., & Kazancı, Z. (2020). Crushing investigation of crash boxes filled with honeycomb and re-entrant (auxetic) lattices. Thin-Walled Structures, 150, 106676. https://doi.org/10.1016/j.tws.2020.106676
6. Prabhaharan, S. A., Balaji, G., Annamalai, K., & Gobinath, V. M. (2022). Robust design assessment of automotive crash box structures through model order reduction. International Journal of Crashworthiness. https://doi.org/10.1080/13588265.2022.2074937
7. Palombini, F. L., Mariath, J. E. A., & de Oliveira, B. F. (2020). Bionic design of thin-walled structure based on the geometry of the vascular bundles of bamboo. Thin-Walled Structures, 155, 106936. https://doi.org/10.1016/j.tws.2020.106936
8. Deng, Y., & Jin, Y. (2025). Compressive mechanical properties of a novel three-dimensional auxetic structure based on additive manufacturing. Thin-Walled Structures, 207, 112719. https://doi.org/10.1016/j.tws.2024.112719

9. Alabtah, F. G., Mahdi, E., & Khraisheh, M. (2024). Energy absorption characteristics of a bio-inspired prepreg carbon fiber crash box under quasi-static axial compression. Composites Part C: Open Access, 14, 100487. https://doi.org/10.1016/j.jcomc.2024.100487
10. Isaac, C. W., Duddeck, F., & Ha, N. S. (2025). Axial crushing response of novel toothed gear bio-inspired 3D printed energy absorbing structures. International Journal of Mechanical Sciences, 288, 110033. https://doi.org/10.1016/j.ijmecsci.2025.110033
11. Günaydın, K., Gülcan, O., & Türkmen, H. S. (2023). Experimental and numerical crushing performance of crash boxes filled with re-entrant and anti-tetrachiral auxetic structures. International Journal of Crashworthiness, 28(5), 649–663. https://doi.org/10.1080/13588265.2022.2115962
12. Sun, G., Chen, D., Zhu, G., & Li, Q. (2022). Lightweight hybrid materials and structures for energy absorption: A state-of-the-art review and outlook. Thin-Walled Structures, 172, 108760. https://doi.org/10.1016/j.tws.2021.108760
13. Tan, H., et al. (2021). Crashworthiness design and multi-objective optimization of a novel auxetic hierarchical honeycomb crash box. Structural and Multidisciplinary Optimization, 64(4), 2009–2024. https://doi.org/10.1007/s00158-021-02961-9
14. Kopar, M., & Yildiz, A. R. (2023). Experimental investigation of mechanical properties of PLA, ABS, and PETG 3D printing materials using fused deposition modeling technique. Materials Testing, 65(12), 1795–1804. https://doi.org/10.1515/mt-2023-0202
15. Sood, M., Wu, C. M., & Yang, Y. C. (2024). Mechanical properties of 3D-printed lattice cylindrical structure with recyclable elastomeric and thermoplastic polymers. Journal of Polymers and the Environment, 32(9), 4196–4212. https://doi.org/10.1007/s10924-024-03203-x
16. Liu, Z., Wang, Y., Liang, X., & Yu, W. (2024). Crashworthiness study of functional gradient lattice-reinforced thin-walled tubes under impact loading. Materials, 17(10), 1–19. https://doi.org/10.3390/ma17102264
17. Xu, F., Yu, K., Hua, L., & Niu, X. (2022). Crashworthiness design of crash box filled with negative Poisson’s ratio based on horn structure. Mechanics of Advanced Materials and Structures, 29(27), 6403–6420. https://doi.org/10.1080/15376494.2021.1978594
18. Gunaydin, K. (2024). Energy absorption ability of crush boxes filled with strut-based and TPMS lattice structures. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 46(11). https://doi.org/10.1007/s40430-024-05207-z
19. Kopar, M., Erdaş, M. U., & Yildiz, A. R. (2024). Experimental investigation on mechanical properties of CF15PET and GF30PP materials produced with different raster angles. Materials Testing, 66(6), 847–855. https://doi.org/10.1515/mt-2023-0226
20. Wei, X., & Deng, X. (2024). Crashworthiness analysis of axially varying thickness multi-cell tubes based on origami folding under oblique impact. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 46(12). https://doi.org/10.1007/s40430-024-05300-3
21. Kopar, M., & Yıldız, A. R. (2024). Experimental and numerical investigation of crash performances of additively manufactured novel multi-cell crash box made with CF15PET, PLA, and ABS. Materials Testing, 66(9), 1510–1518. https://doi.org/10.1515/mt-2024-0100
22. Cronau, J., & Engstler, F. (2025). Energy absorption of 3D printed stochastic lattice structures under impact loading: Design parameters, manufacturing, and testing. Progress in Additive Manufacturing. https://doi.org/10.1007/s40964-025-01094-5
23. Cho, J., Lee, E. S., Kim, J. H., Lee, C. Y., & Cho, J. Y. (2025). Design of lattice-based energy-absorbing structure for enhancing the crashworthiness of advanced air mobility. Aerospace, 12(4), 332. https://doi.org/10.3390/aerospace12040332
24. Tao, C., et al. (2023). Crashworthiness of additively manufactured lattice reinforced thin-walled tube hybrid structures. Aerospace, 10(6). https://doi.org/10.3390/aerospace10060524
25. Tao, C., Zhou, X., Liu, Z., Liang, X., Zhou, W., & Li, H. (2023). Crashworthiness study of 3D printed lattice reinforced thin-walled tube hybrid structures. Materials, 16(5). https://doi.org/10.3390/ma16051871
26. Astuti, F. A. F., Choiron, M. A., Purnowidodo, A., & Irawan, Y. S. (2025). Quasi-static test data set of honeycomb hybrid tubes by FDM 3D printing. Data in Brief, 58. https://doi.org/10.1016/j.dib.2024.111233
27. Kosedag, E. (2025). Investigation of cell size influence on the crushing behavior of gyroid lattices fabricated via FDM. Mechanics of Advanced Materials and Structures. https://doi.org/10.1080/15376494.2025.2486750
28. Alemayehu, D. B., & Todoh, M. (2024). Enhanced energy absorption with bioinspired composite TPMS gyroid lattices fabricated via FFF. Journal of Manufacturing and Materials Processing, 8(3). https://doi.org/10.3390/jmmp8030086
29. Kandasamy, M. K., & Ganesan, A. (2024). Crashworthiness study of polyamide bi-tubular thin-walled tubes using hybrid lattice filling. Journal of Cellular Plastics, 61(1), 37–60. https://doi.org/10.1177/0021955X241290878
30. Xie, S., Zheng, S., Zhang, J., Liu, Z., Wang, H., & Zhou, H. (2024). Study on the crashworthiness of multi-cell thin-walled tubes filled with triply periodic minimal surface lattices. Mechanics of Advanced Materials and Structures, 32(3), 307–323. https://doi.org/10.1080/15376494.2024.2345206
31. Awd Allah, M. M., Abd El-Halim, M. F., Sebaey, T. A., Mahmoud, S. F., Saleh, D. I., & Abd El-baky, M. A. (2025). Multi-criteria decision-making for optimizing crashworthiness of 3D-printed PETG-CF lightweight structures. Polymer Composites. https://doi.org/10.1002/pc.29826
32. Tang, C., Liu, J., Yang, Y., Liu, Y., Jiang, S., & Hao, W. (2020). Effect of process parameters on mechanical properties of 3D printed PLA lattice structures. Composites Part C: Open Access, 3. https://doi.org/10.1016/j.jcomc.2020.100076
33. Saleh, M., Anwar, S., Al-Ahmari, A. M., & Alfaify, A. (2022). Compression performance and failure analysis of 3D-printed carbon fiber/PLA composite TPMS lattice structures. Polymers, 14(21). https://doi.org/10.3390/polym14214595
34. Kocabaş, G. B., Yalcinkaya, S., Cetin, E., & Sahin, Y. (2024). Energy absorption of a novel lattice structure-filled multicell thin-walled tubes under axial and oblique loadings. Advanced Engineering Materials, 26(20). https://doi.org/10.1002/adem.202400483
35. Kocabaş, G. B., Çetin, E., Yalçınkaya, S., & Şahin, Y. (2023). Experimental comparison of the energy absorption performance of traditional lattice and novel lattice filled tubes. International Journal of Automotive Science and Technology, 7(3), 207–212. https://doi.org/10.30939/ijastech.1331192
36. Sultan, M., Kandil, A., & Baraya, M. (2025). Crashworthiness performance evaluation of thin-walled tubes filled with single and hybrid lattice structures under axial impact loading using finite element analysis. International Journal of Automotive Science and Technology, 9(3), 284–293. https://doi.org/10.30939/ijastech.1711179

Details

Primary Language

English

Subjects

Automotive Safety Engineering

Journal Section

Research Article

Authors

Mehmet Kopar ^*
0000-0001-7347-4192
Türkiye

Publication Date

April 14, 2026

Submission Date

January 11, 2026

Acceptance Date

April 5, 2026

Published in Issue

Year 2026 Volume: 6 Number: 2

DOI

https://doi.org/10.64808/engineeringperspective.1861151

IZ

https://izlik.org/JA95MU67BE

Cite

RIS / Bibtex

APA

Kopar, M. (2026). Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures. Engineering Perspective, 6(2), 287-296. https://doi.org/10.64808/engineeringperspective.1861151

AMA

1.Kopar M. Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures. engineeringperspective. 2026;6(2):287-296. doi:10.64808/engineeringperspective.1861151

Chicago

Kopar, Mehmet. 2026. “Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced With Lattice Structures”. Engineering Perspective 6 (2): 287-96. https://doi.org/10.64808/engineeringperspective.1861151.

EndNote

Kopar M (April 1, 2026) Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures. Engineering Perspective 6 2 287–296.

IEEE

[1]M. Kopar, “Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures”, engineeringperspective, vol. 6, no. 2, pp. 287–296, Apr. 2026, doi: 10.64808/engineeringperspective.1861151.

ISNAD

Kopar, Mehmet. “Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced With Lattice Structures”. Engineering Perspective 6/2 (April 1, 2026): 287-296. https://doi.org/10.64808/engineeringperspective.1861151.

JAMA

1.Kopar M. Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures. engineeringperspective. 2026;6:287–296.

MLA

Kopar, Mehmet. “Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced With Lattice Structures”. Engineering Perspective, vol. 6, no. 2, Apr. 2026, pp. 287-96, doi:10.64808/engineeringperspective.1861151.

Vancouver

1.Mehmet Kopar. Experimental and Numerical Investigation of ABS and PLA Material Crash Boxes Reinforced with Lattice Structures. engineeringperspective. 2026 Apr. 1;6(2):287-96. doi:10.64808/engineeringperspective.1861151