A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER

Kerim Örüklü; Deniz Yıldırım

doi:10.18038/estubtda.978478

EN TR

A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER

Abstract

In this paper, a peak current mode controlled single ended primary inductor converter (SEPIC) LED driver is proposed to control the brightness of the LED. One string of 37 series connected LEDs is adopted as output of the circuit. The proposed control strategy is based on measuring MOSFET peak current value using a shunt resistor. When this voltage reaches peak threshold value, controller turns off MOSFET. The output current is adjusted to desired levels by changing this peak threshold value. The power factor in the AC power supply side is low because of the full wave bridge rectifier with capacitor filter at the input of the converter. The proposed control strategy is applied with power factor correction (PFC) circuit where input voltage is multiplied by control voltage to achieve high power factor. In PFC circuit, although the line current waveform is slightly distorted due to voltage limitations in integrated circuit (IC) chip used for the proposed control strategy, power factor is kept above 0.9 for operation region between 100mA-300mA. In addition, flicker on LED string is measured for operating current region and flicker limits are revealed. Adjustable output current levels, low flicker on LED string, MOSFET peak current control at each cycle, fast output dynamics, and high power factor are acquired by the proposed control strategy.

Keywords

Light emitting diode, Peak current mode control, Flicker, Power factor correction circuit, Single ended primary inductor converter

GÜÇ FAKTÖRÜ VE FLICKERI DİKKATE ALAN BİR TEPE AKIM MODU KONTROLLÜ SEPİC LED SÜRÜCÜ TASARIMI

Abstract

Bu çalışmada, LED’in parlaklığını denetleyebilmek için tepe akım modu kontrollü SEPİC LED sürücü devresi önerilmiştir. Devrenin çıkışı, tek dizi 37 seri bağlanmış LED’den oluşmaktadır. Önerilen kontrol stratejisi, bir direnç kullanarak MOSFET’in tepe akımını ölçmeye dayanmaktadır. Bu akım değeri, tepe eşik değerine ulaştığında, kontrolcü MOSFET’i kapatmaktadır. Tepe eşik değeri değiştirilerek, çıkış akımı istenilen seviyelere ayarlanmaktadır. Devrenin giriş kısmındaki tam dalga köprü doğrultucu ve kondansatör sebebiyle AC güç kaynağı tarafında güç faktörü düşüktür. Önerilen kontrol stratejisi, yüksek güç faktörü elde etmek için kontrol gerilimi ile giriş geriliminin çarpıldığı güç faktörü düzelten devreye uygulanmıştır. Güç faktörü düzelten devrede, önerilen kontrol stratejisinde kullanılan entegre devresindeki gerilim kısıtlamaları nedeniyle giriş akımı kısmen bozulmasına rağmen, 100mA-300mA arasındaki çalışma bölgesinde güç faktörü 0.9 üzerinde tutulmuştur. Buna ek olarak, çalışma akımları için LED dizisindeki flicker ölçülmüş ve flicker limitleri ortaya konulmuştur. Önerilen kontrol stratejisi ile her periyot için MOSFET tepe akımı kontrolü sağlanmış ve ayarlanabilir çıkış akımı, hızlı çıkış dinamikleri, yüksek güç faktörü, LED dizisinde düşük flicker elde edilmiştir.

Keywords

Işık Yayan Diyot, Tepe Akım Modu Kontrolü, Güç Faktörü Düzeltici Devre, SEPİC, Flicker

References

[1] Chiu HJ, Lo YK, Chen JT, Cheng SJ, Lin CY, Mou SC. A high-efficiency dimmable LED driver for low-power lighting applications. IEEE T Ind Electron, 2010; 57: 735-743.
[2] Yadav A, Pachauri RK, Chauhan YK. Power quality improvement using PFC SEPIC converter for LED bulb adaptable for universal input voltage. In: 2016 IEEE 1st International Conference on Power Electronics, Intelligent Control and Energy Systems (ICPEICES); 4-6 July 2016; Delhi, India: IEEE, 1-6.
[3] Ye Z, Greenfeld F, Liang Z. Design considerations of a high power factor SEPIC converter for high brightness white LED lighting applications. In: 2008 IEEE Power Electronics Specialists Conference; 15-19 June 2008; Rhodes, Greece: IEEE, 2657-2663.
[4] Wang Y, Alonso JM, Ruan X. A Review of LED Drivers and Related Technologies. IEEE T Ind Electron, 2017; 64: 5754-5765.
[5] Şehirli E, Altınay M, Üstün Ö, Çakır B. Comparison of single phase buck-boost and sepic LED driver. Light Eng, 2017; 25: 92-98.
[6] Hayirli IH, Kelleci B, Kivanc OC, Ozturk SB, Tuncay RN, Citci MO. Design and Analysis of 240 Watt SEPIC Converter for LED Applications. In: 2019 IEEE 28th International Symposium on Industrial Electronics (ISIE); 12-14 June 2019; Vancouver, BC, Canada: IEEE, 804-809.
[7] Kouzou A. Power Factor Correction Circuits. In: Power Electronics Handbook. 4th ed. Elsevier Inc, 2018; 529-569.
[8] IEEE Power Electronics Society. IEEE Recommended Practices for Modulating Current in High-Brightness LEDs for Mitigating Health Risks to Viewers. In: IEEE Std 1789-2015; 1-80.
[9] Energy Focus. (2017). Optical Flicker in Lighting [Online]. Available: www.energyfocus.com.
[10] Mishra AK et al. Average current-controlled SEPIC converter with high power factor correction. In: Innovation in Electrical Power Engineering, Communication, and Computing Technology. Springer, 2020; 451-463.

[11] Lamar DG, Zúñiga JS, Alonso AR, González MR, Álvarez MMH. A very simple control strategy for power factor correctors driving high-brightness LEDs. IEEE T Power Electr, 2009; 24: 2032-2042.
[12] Şehirli E, Üstün Ö. Design and Application of High Power Factor SEPIC LED Driver. In: 2016 National Conference on Electrical, Electronics and Biomedical Engineering (ELECO); 1-3 Dec. 2016; Bursa, Turkey: IEEE, 115–119.
[13] Wang Y, Huang J, Shi G, Wang W, Xu D. A single-stage single-switch LED driver based on the integrated SEPIC circuit and class-E converter. IEEE T Power Electr, 2016; 31: 5814-5824.
[14] Mahadeokar S, Sardeshmukh M. Energy efficient PWM Dimmable Smart Digital LED driver. In: 2015 International Conference on Energy Systems and Applications; 30 Oct.-1 Nov. 2015; Pune, India: IEEE; 306-311.
[15] Umar MW, Yahaya N, Baharuddin Z. PWM Dimming for High Brightness LED Based Automotive Lighting Applications. In: International Journal of Electrical and Computer Engineering (IJECE) 7.5; 2017; 2434-2440.
[16] Ali M, Orabi M, Ahmed ME, El-Arouidi A. A single stage SEPIC PFC converter for LED stage lighting applications. In: 2010 IEEE International Conference on Power and Energy; 29 Nov.- 1 Dec. 2010; Kuala Lumpur, Malaysia: IEEE, 501-506.
[17] Ali M, Orabi M, Ahmed ME, El-Arouidi A. Design considerations of a single-stage LED lamp driver with power factor correction. In: 2011 2nd International Conference on Electric Power and Energy Conversion Systems (EPECS); 15-17 Nov. 2011; Sharjah, United Arab Emirates: IEEE, 1-6.
[18] Avago Technologies. Driving High Power and High Brightness LEDs Application Note 5310 [Online]. Available: www.avagotech.com; 2010, July 21.
[19] Karaarslan A. Bilgisayar Sistemlerinde SEPIC Dönüştürücü Uygulaması ve Benzetim Çalışması. Bilişim Teknolojileri Dergisi, 2019; 12: 111–117.
[20] ST Microelectronics; 1995. UC3842 Provides Low-Cost Current-Mode Control Application Note [Online]. Available: https://www.st.com/content/st_com/en.html.
[21] Texas Instruments; 1999. U-100A Uc3842/3/4/5 Provides Low-Cost Current-Mode Control Application Notes [Online]. Available: www.ti.com.

Details

Primary Language

English

Subjects

Engineering

Journal Section

Research Article

Authors

Kerim Örüklü ^*
0000-0002-9544-0898
Türkiye

Deniz Yıldırım
0000-0001-6216-6290
Türkiye

Publication Date

March 30, 2022

Submission Date

August 4, 2021

Acceptance Date

March 25, 2022

Published in Issue

Year 2022 Volume: 23 Number: 1

DOI

https://doi.org/10.18038/estubtda.978478

IZ

https://izlik.org/JA26BN72YN

APA

Örüklü, K., & Yıldırım, D. (2022). A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering, 23(1), 109-125. https://doi.org/10.18038/estubtda.978478

AMA

1.Örüklü K, Yıldırım D. A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER. Estuscience - Se. 2022;23(1):109-125. doi:10.18038/estubtda.978478

Chicago

Örüklü, Kerim, and Deniz Yıldırım. 2022. “A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER”. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering 23 (1): 109-25. https://doi.org/10.18038/estubtda.978478.

EndNote

Örüklü K, Yıldırım D (March 1, 2022) A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering 23 1 109–125.

IEEE

[1]K. Örüklü and D. Yıldırım, “A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER”, Estuscience - Se, vol. 23, no. 1, pp. 109–125, Mar. 2022, doi: 10.18038/estubtda.978478.

ISNAD

Örüklü, Kerim - Yıldırım, Deniz. “A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER”. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering 23/1 (March 1, 2022): 109-125. https://doi.org/10.18038/estubtda.978478.

JAMA

1.Örüklü K, Yıldırım D. A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER. Estuscience - Se. 2022;23:109–125.

MLA

Örüklü, Kerim, and Deniz Yıldırım. “A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER”. Eskişehir Technical University Journal of Science and Technology A - Applied Sciences and Engineering, vol. 23, no. 1, Mar. 2022, pp. 109-25, doi:10.18038/estubtda.978478.

Vancouver

1.Kerim Örüklü, Deniz Yıldırım. A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER. Estuscience - Se. 2022 Mar. 1;23(1):109-25. doi:10.18038/estubtda.978478

A PEAK CURRENT MODE CONTROLLED SEPIC LED DRIVER DESIGN CONSIDERING POWER FACTOR AND FLICKER

Abstract

Keywords

GÜÇ FAKTÖRÜ VE FLICKERI DİKKATE ALAN BİR TEPE AKIM MODU KONTROLLÜ SEPİC LED SÜRÜCÜ TASARIMI

Abstract

Keywords

References

Details

Primary Language

Subjects

Journal Section

Authors

Publication Date

Submission Date

Acceptance Date

Published in Issue

DOI

IZ

Cite