EVALUATION OF SURFACE ROUGHNESS IN DRILLING OF AA 7075 T6 PLATE WITH DIFFERENT CUTTING TOOL GEOMETRIES WITH EXPERIMENTAL, STATISTICAL AND DEFORM 3D SIMULATION

Yıl 2022, Cilt: 6 Sayı: 2, 314 - 321, 31.08.2022

Ömer Erkan

https://doi.org/10.46519/ij3dptdi.1138710

Öz

The basis of the study is to examine the average surface roughness (Ra) value resulting from drilling AA 7075 T6 plates with drills with different point angles () and under different cutting parameters. However, two different point angles (118° and 135°), three different cutting speeds (Vc) (40, 60 and 80 m/min) and three different feeds (f) (0.04, 0.08 and 0.12 mm/rev) were preferred in the experiments. The effect of cutting and tool geometry parameters on Ra was digitized by performing an ANOVA analysis. It was determined that Ra increased with the increase of Vc,  and f. The parameter with the most significant effect on Ra was Vc with 49.10%, followed by  with 30.52% and f with 13.67%, respectively. In order to examine the reasons for the increase in Ra value more effectively, drilling simulations were carried out under different cutting parameters using Deform 3D software. The simulation estimated temperature, cutting force and damage during drilling. The predicted results and the factors on Ra were revealed. In the experiments carried out with the drill with a tip angle of 135°, it was estimated that the temperature, the temperature, the cutting force and the damage value along the Z-axis were higher than the drill with a tip angle of 118°.

Anahtar Kelimeler

AA 7075 T6 plate, Drilling, Drill bit point angle, Surface roughness, Simulation of Deform 3D

Kaynakça

• 1. Çakır, A., Nalbant, M., Duran, A., Ulaş, H.B., “AA 7075 Ve AA 6013 “Alüminyum Malzemelere Delik Delme Operasyonu Sürecinde Kesme Parametrelerinin İncelenmesi”, 3. Ulusal Talaşlı İmalat Sempozyumu, Pages 09-18, Ankara, 2012.
• 2. Çaydaş, U., Çelik, M., “Investigation of the Effects of Cutting Parameters on The Surface Roughness, Tool Temperature and Thrust Force in Drilling of AA 7075-T6 Alloy”, Journal of Polytechnic, Vol.20 Issue 2, Pages 419-425, 2017.
• 3. Erkan, Ö., Yücel, E., “Optimization and statistical analysis of surface roughness of the drilled hole surfaces on the AA 7075 material”, International Eurasian Conference on Science, Engineering and Technology (EurasianSciEnTech 2018), Pages 788-795, Ankara, 2018.
• 4. E. Kilickap et. al., “Modeling and optimization of burr height in drilling of Al-7075 using Taguchi method and response surface methodology”, International Journal of Advanced Manufacturing Technology, Vol.49, Pages 911–923, 2010.
• 5. Ferrer, C.P.,“Optimizing the Strength and SCC Resistance of Aluminium Alloys Used for Refurbishing Aging Aircraft”, U.S.N.A Trident Scholar project report, 2001.
• 6. Gopalakrishnan, K., Dineshragupathy, S., Elavarasan, M., Gopinath, K., Vignesh, L., “Optimization Of Machining Parameters In Drilling Of Al7075 Alloy Using RSM Methodology”, EPH - International Journal of Science and Engineering, Vol.1 Issue 1, Pages 173-177, 2018.
• 7. Han, Y.; Samuel, A.M.; Doty, H.W.; Valtierra, S.; Samuel, F.H. “Optimizing the tensile properties of Al-Si-Cu-Mg 319-type alloys: Role of solution heat treatment”, Materials and Design, Vol.58, Pages 426–438, 2014.
• 8. Heinz, A., Haszler, A., Keidel, C., Moldenhauer, S., Benedictus, R., Miller, W S., “Recent Development in Aluminium Alloys for Aerospace Applications”, Mater. Sci. Eng. A -Structural Materials Properties, Vol.280, Pages 102-107, 2000.
• 9. Kurt, M., Kaynak, Y., and Bagci, E., “Evaluation of drilled hole quality in Al 2024 alloy”, Int J Adv Manufacturing Technology, Vol.37, Pages 1051–1060, 2008.
• 10. Kushnoore, S. Noel, D., Kamitkar, N., Satishkumar, M., “Experimental Investigations on Thrust, Torque and Circularity Error in Drilling of Aluminium Alloy (Al6061)”, American Journal of Mechanical and Industrial Engineering, Vol.1, Issue 3, Pages 96-102, 2016.
• 11. Ogris, E., Wahlen, A., Luchinger, H., Uggowitzer, P.J., “On the silicon spheroidization in Al-Si alloys”, Journal of Light Metals, Vol. 2, Pages 263–269, 2002.
• 12. Rendigs K H., “Aluminium Structures Used in Aerospace-Status and Prospects”, Journal of Material Science Forum, Vol.242, Pages 11-24, 1997.
• 13. Sakarya N., Göloğlu C., “Determination of Cutter Path Strategies and Cutting Parameters Effects on Surface Roughness in Pocket Milling by Taguchi Method”, Journal of the Faculty of Engineering and Architecture of Gazi University, Vol.21, Issue 4, Pages 603–611, 2006.
• 14. Savaşkan M., Taptık Y., Ürgen M., “Deney tasarımı yöntemi ile matkap uçlarında performans optimizasyonu”, İtü dergisi /d mühendislik Vol.3, Issue 6, Pages 117-128, 2004.
• 15. Sjölander, E.; Seifeddine, S. “Optimisation of solution treatment of cast Al-Si-Cu alloys”, Materials and Design, Vol.31, Pages 44–49, 2010.
• 16. Smith, W.E., Structure and Properties of Engineering Alloys, Non-Ferrous Alloys, Vol.2, Translation M. Erdoğan, Nobel Dağıtım, 2001.
• 17. Tillová, E.; Chalupová, M.; Kuchariková, L.; Belan, J.; Závodská, D., “Selection of optimal solution heat treatment of the casting cylinder heads”, MATEC Web Conference, Vol.157, Pages 1-12, 2018.
• 18. Turgut E., Dikici A., “Optimization of design parameters of co-axial heat exchanger with Taguchi method”, 6th International Advanced Technologies Symposium (IATS’11), Elazığ, Turkey, Pages 278–281, 2011.
• 19. Wu, YL., Froes F.H, Alvarez A,, Li CG,, Liu J., “Microstructure and Properties of a New Super-High-Strength Al–Zn–Mg–Cu alloy C912”, Materials and Design, Vol.18, Pages 211–215, 1997.
• 20. Yurdakul, M., Özbay, O., İç, Y. T., “Selection of Aerospace Aluminium Alloys”, Journal of the Faculty of Engineering Architecture of Gazi University, Vol. 17, Issue 2, Pages 1-23, 2002.
• 21. Zhang, D.L.; Zheng, L.H.; StJohn, D.H., “Effect of a short solution treatment time on microstructure and mechanical properties of modified Al-7wt.%Si-0.3wt.%Mg alloy”, Journal of Light Metals, Vol.2, Pages 27–36, 2002.