Heat and Flow Analysis of Different Piston Bowl Geometries in a Diesel Engine

Yıl 2021, Cilt: 5 Sayı: 3, 206 - 213, 30.09.2021

İlker Temizer , Ömer Cihan

https://doi.org/10.30939/ijastech..929299

Cited By: 3

Öz

In this study, heat and flow in a four cylinder direct injection diesel engine combustion chamber has been simulated by using AVL Fire ESE Diesel. In order to clarify the effect of the combustion chamber geometry on the flow area prop-erties, the bowl geometric shape of two different pistons, one of the combustion chamber as a standard, was taken into account in the flow analysis. Standard combustion chamber and modified combustion chamber geometries have been compared. The simulation results showed that the bowl shapes of the combustion chambers are quite effective on temperature-spray droplet distribution, turbu-lence kinetic energy distributions, turbulence velocity distributions and laminar flame speed distributions at the end of the compression stroke. The fuel reaches the cylinder wall more easily and then, the temperature distribution in the cham-ber is lower as a result of evaporation of the fuel with modified combustion chamber. Average turbulent kinetic energy value in the MCC type combustion chamber is 10.53 m²/s², in the standard combustion chamber type combustion chamber this value is 8.35 m²/s² at 720° CA. Turbulence velocity distribution is spread over a wider area in the modified combustion chamber geometry. As a re-sult of the large area of turbulence, the laminar flame velocity has also increased in this chamber geometry.

Anahtar Kelimeler

In-cylinder flows, Bowl geometry, Diesel engine, AVL Fire

Kaynakça

• Demirci, A. The effects of different combustion chamber geometries on the performance and emissions of an internal combustion engine, PhD Thesis, Istanbul Technical University, Institute of science and technology, 2017.
• Ayaz, E., Koten, H., Cadirci, S. Numerical investigation of cold air flow inside the cylinder of a heavy duty diesel engine, International Journal of Advances in Engineering and Pure Sciences, 2018, 30(4): 445-452.
• Yilmaz, M. Comparison of ethanol and gasoline in engine cylinder flow, Msc Thesis, Bursa Uludag University, Institute of science and technology, 2019.
• Abay, K., Colak, U., Yuksek, L. Computational fluid dynamics analysis of flow and combustion of a diesel engine, Journal of Thermal Engineering, 2018, 4(2): 1878-1895.
• Monaghan, M.N., Pettifer, H.F. Air motion and its effect on diesel performance and emissions, SAE Technical Paper, 1981, 810255, 19-35.
• Shimoda, M., Shigemori, M., Tsuruoka, S. Effect of combustion chamber configuration on in-cylinder air motion and combustion characteristics of D.I. Diesel engine, SAE Technical Paper, 1985, 850070, 1-13.
• Buyukkaya, E. Flow modeling in a DI Diesel engine combustion chamber using CFD, Fuels, Fire and Combustion in Engineering Journal, 2016, 2, 31-38.
• Kaplan, M., Influence of swirl, tumble and squish flows on combustion characteristics and emissions in internal combustion engine-review, International Journal of Automotive Engineering and Technologies, 2019, 8(2): 83-102.
• Stephenson, P.W., Claybaker, P.J., Rutland, C.J. Modeling the Effects of intake generated turbulence and resolved flow structures on combustion in DI Diesel engines, SAE Technical Paper, 1996, 960634, 103-117.
• Gunabalan, A., Ramprabhu, R. Effect of piston bowl geometry on flow, combustion and emission in DI engines-a CFD approach, International Journal of Applied Engineering Research, 2009, 4(11): 2181–2188.
• Zheng, Z., Liu, C., Tian, X., Zhang, X. Numerical study of the effect of piston top contour on GDI engine performance under catalyst heating mode, Fuel, 2015, 157, 64-72.
• Chu, S., Shin, H., Kim, K., Moon, S., Min, K., Jung, H., Kim, H., Chi, Y. An experimental investigation of in-cylinder flow motion effect on dual-fuel premixed compression ignition characteristics, SAE Technical Paper, 2020, 2020-01-0306, 1-12.
• Heywood, J.B. Internal Combustion Engine Fundamentals, 2nd edition, McGraw-Hill Education, United States, 2018.
• Perini, F., Zha, K., Busch, S., Kurtz, E., Peterson, R.C., Warey, A., Reitz, R.D. Piston geometry effects in a light-duty, swirl-supported diesel engine: Flow structure characterization, International Journal of Engine Research, 2018, 19(10): 1079-1098.
• Khan, S., Panua, R., Bose, P.K. Combined effects of piston bowl geometry and spray pattern on mixing, combustion and emissions of a diesel engine: A numerical approach, Fuel, 2018, 225, 203-217.
• Sener, R., Ozdemir, M.R., Yangaz, M.U. Influence of piston bowl geometry on combustion and emission characteristics, Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 2019, 233(5): 576–587.
• Li, J., Yang, W.M., An, H., Maghbouli, A., Chou, S.K. Effects of piston bowl geometry on combustion and emission characteristics of biodiesel fueled diesel engines, Fuel, 2014, 120, 66-73.
• Mohan, B., Yang, W., Yu, W., Tay, K.L., Chou, S.K. Numerical investigation on the effects of injection rate shaping on combustion and emission characteristics of biodiesel fueled CI engine, Applied Energy, 2015, 160, 737-745.
• Aksoy, F., Yilmaz, E. An investigation of combustion and performance characteristics of a direct injection diesel engine fuelled with the blends of 10% fish oil biodiesel and 90% diesel fuel, Gazi University Journal of Science Part C: Design and Technology, 2019, 7(1): 12-24.
• Lešnik, L., Kegl, B., Torres-Jiménez, E., Cruz-Peragón, F., Mata, C., Biluš, I. Effect of the in-cylinder back pressure on the injection process and fuel flow characteristics in a common-rail diesel injector using GTL fuel, Energies, 2021, 14, 452, 1-21.
• Bishop, D., Situ, R., Brown, R., Surawski, N. Numerical modelling of biodiesel blends in a diesel engine, Energy Procedia, 2017, 110, 402-407.
• Hasan, A.A.K.M., Mashkour, M.A., Mohammed, A.A. Burning velocity measurement of biodiesel fuel and its blends using particle imaging path technique and image processing, Journal of Engineering and Sustainable Development, 2018, 22(2): 1-17.
• Temizer, I, Eskici, B. Investigation on the combustion characteristics and lubrication of biodiesel and diesel fuel used in a diesel engine, Fuel, 2020, 278, 1-9.