Application of Geoinformatics in Civil Engineering Design and Construction: A Case Study of Ile Oluji, SW Nigeria

Yıl 2023, Cilt: 10 Sayı: 4, 117 - 145, 26.12.2023

Olumuyiwa Falowo

https://doi.org/10.30897/ijegeo.1262020

Öz

Subsoil engineering site condition and modeling of engineering parameters has been carried out in Ile Oluji, Ondo State, Southwestern Nigeria, using geotechnical investigation, geophysical method, borehole logging, groundwater level measurement, and laboratory studies. Findings revealed that the soils are clayey of low-high plasticity/compressibility, with AASHTO classification of A-7-6. Based on average values of cohesion (48.4 KN/m2), angle of friction (17.4°), unconfined compressive strength (186.8 KN/m2), coefficient of permeability (2.13E-06 cm/s), activity (0.48), soaked CBR (7 %), MDD/OMC (1980 kg/m3/14.8 %), plasticity index (20.2 %), group index (6 %), compression index (0.0443), coefficient of volume compressibility (0.2041 m2/KN), depth to basement rock (22.2 m), static water levels 5.5 m (in well) and 21.8 m (in borehole), the soil is unsuitable for highway subgrade, subbase, and base courses. Thus, if it is expedient to use it as subgrade soil, the minimum recommended thickness is 241 – 513 mm (avg. 395 mm). The average allowable bearing capacity of the soil for square and round foundations are 268.4 KN/m2 and 267.95 KN/m2 respectively, with average total settlement of 18.3 mm for structural pressure of 100 KN/m2. For embankment, the suitability index (1.21) of the soil suggests a fair/expanding not collapsible construction material. The rock units in the area have high compressive/shear strength, modulus of elasticity, high crushing strength, low deformability; and presumable bearing capacity of 8, 000 – 10, 000 KPa when fresh, and 5000 – 7000 KPa when partly or slightly weathered. Thus are valuable as foundation constructions, aggregate in pavement, building stone, and armourstones. The correlation coefficient of the parameters are: MDD/PI vs. CBR (0.0043), LL vs. coefficient of consolidation (0.0608), PI vs. undrained shear strength/effective overburden (0.2706), PI vs. angle of shearing (0.0117), dry density vs. angle of shearing (0.0058), suitability index vs. CBRs (0.3644), clay contents vs. PI (0.1355).

Anahtar Kelimeler

Embankment, Pavement, Geoinformatics, Geotechnics

Kaynakça

• AASHTO (2006). Standard Specifications for Transportation Materials and Methods of Sampling and Testing, Parts I and II, American Association of State Highway and Transportation Officials, Washington, D.C.
• Adejumo, S.A., Oyerinde, A.O., Akeem, M.O. (2015). Integrated geophysical and geotechnical subsoil evaluation for pre-foundation study of proposed site of vocational skill and entrepreneurship center at the polytechnic, Ibadan, SW, Nigeria. Int J Sci Eng Res 6: 910-917.
• Adewuyi, O.I., Philips, O.F. (2018). Integrated Geophysical and Geotechnical Methods for Pre-Foundation Investigations. J Geol Geophys 8: 453. doi:10.4172/2381-8719.1000453
• Alabi, A.A., Adewale, A.O., Coker, J.O., Ogunkoya, O.A. (2017). Site Characterization for Construction Purposes at FUNAAB using Geophysical and Geotechnical Methods, RMZ – M&G, Vol. 65, pp. 089–102. DOI: 10.2478/rmzmag-2018-0007
• Alaminiokuma, G.I., Chaanda, M.S. (2020). Geophysical Investigation of Structural Failures Using Electrical Resistivity Tomography: A Case Study of Buildings in FUPRE, Nigeria. Journal of Earth Sciences and Geotechnical Engineering, Vol.10, No.5, 2020, 15-33.
• Archana, P.M., Padma, K.R. (2016). Engineering and Geological Evaluation of Rock Materials as Aggregate for Pavement Construction. International Advanced Research Journal in Science, Engineering and Technology, Vol. 3, Special Issue 3, August 2016. DOI 10.17148/IARJSET
• Arora, K.R. (2008). Soil mechanics and foundation engineering (Geotechnical Engineering). Standard Publishers Distributors, Delhi.
• ASTM (2006). Annual Book of ASTM Standards – Sections 4.02, 4.08, 4.09 and 4.13. ASTM International, West Conshohocken, PA.
• Attewell, P.B., Farmer, I.W. (1988). Principles of engineering geology Principles of Engineering Geology John Wiley & Sons, Inc, New York, 1045pp. ISBN-13: 978-94-009-5709-1 DOl: 101007/978-94-009-5707-7
• Bawallah, M.A., Ilugbo, S.O., Ozegin, K.O., Adebo B.A., Aigbedion, I., Salako, K.A. (2021). Electrical Resistivity and Geotechnical Attributes and the Dynamics of Foundation Vulnerability. Indonesian Journal of Earth Sciences, Vol. 1, No. 2 (2021): 84-97. DOI: 10.52562/injoes.v1i2.253
• Bell, F.G. (2007). Engineering Geology Second Edition, Elsevier Limited
• Bell, F.G. (2004). Engineering Geology and Construction Spon Press, London Brassington, R. (1988). Field Hydrogeology. Wiley, Chichester.
• Brown, S.F. (1996). Soil mechanics in pavement engineering. Geotechnique, 46, 383–426. BS 1377 (1990). Methods of Tests for Soils for Civil Engineering Purpose, British Standard Institution HMSO London.
• Burland, J.B., Burbidge, M.C. (1984). Settlement of foundations on sand and gravel, Proceedings of the Institution of Civil Engineers, Part 1, 1985, 78, Dec., 1325-1381.
• Carter, M., Bentley, S.P. (1991). Correlations of soil properties, Pentech Press Publishers, London, 129pp Carter, M., Symons, M.W. (1989). Site Investigations and Foundations Explained. Pentech Press, London.
• Cetin, K.O., Ozan, C. (2009). CPT-based probabilistic soil characterization and classification. J Geotech Geoenviron Eng 135(1):84–107. doi:10.1061/ (ASCE)1090-0241(2009)135:1(84).
• Coker, J.O. (2015). Integration of Geophysical and Geotechnical Methods to Site Characterization for Construction Work at the School of Management Area, Lagos State Polytechnic, Ikorodu, Lagos, Nigeria. International Journal of Energy Science and Engineering, 1(2), 40-48.
• Craig, C. (Ed.). (1996). Advances in Site Investigation Practice. Thomas Telford Press, London. Das, B.M. (2015). Principles of foundation engineering. Cengage learning, Boston
• Eebo, F.O., Samuel, A.B., Olayanju, G.M. (2022). Geophysical and Geotechnical Investigations for Subsoil Competence at a Proposed Hostel Site at Oba Nla, Akure Southwestern Nigeria. Journal of Engineering Research and Sciences, 1(2): 41-49, 2022. DOI: https://doi.org/TBA
• Falowo, O.O., Dahunsi, S.D. (2020). Geoengineering Assessment of Subgrade Highway Structural Material along Ijebu Owo – Ipele Pavement Southwestern Nigeria. International Advanced Research Journal in Science, Engineering and Technology (IARJSET) Vol 7, Issue 4, 10pp. DOI 1017148/IARJSET20207401
• Falowo, O.O., Olabisi, W. (2020). Engineering Geological and Geotechnical Site Characterization for Economic Design of Structures and Earthwork Journal of Research and Innovation for Sustainable Society, 2(2), pp43-60. Doi: 1033727/jriss202027:43-60
• Falowo, O.O., Ojo, O.O., Daramola, A.S. (2015). The use of magnetic survey in engineering site characterization. International Journal of Innovative research and development, Vol., 4(13): pp. 74-85.
• Falowo, O.O. (2019). Engineering properties of some basement rocks of Nigeria as Aggregate in Civil Engineering Pavement Construction. Asian Review of Environmental and Earth Sciences, Vol. 6, No. 1, 28-37. DOI: 10.20448/journal.506.2019.61.28.37
• Faseki, O.E., Olatinpo, O.A., Taiwo, O.B. (2016). Ground Investigation of an Engineering Site at Point Road, Apapa, Lagos, Nigeria. Journal of Engineering and Energy Research, 6(1), pp. 1–20. Federal Meteorological Survey (1982). Atlas of the Federal Republic of Nigeria, 2nd Edition, Federal Surveys, 160pp.
• Federal Ministry of Works and Housing. (1997). General Specifications for Roads and Bridges. Volume II.145-284. Federal Highway Department: Lagos, Nigeria.
• FHWA NHI-05-037. (2006). Geotechnical aspects of pavement. U.S. Department of Transportation Federal Highway Administration, 4-17.
• George, K.P., Uddin, W. (2000). Subgrade characterization for highway pavement design, final report. Jackson, MS: Mississippi Department of Transportation.
• Hatanaka, M., Uchida, A. (1996). Empirical correlation between penetration resistance and effective friction of sandy soil. Soils & Foundations, Vol. 36 (4), 1-9, Japanese Geotechnical Society.
• Hawkins, A.B. (Ed.). (1986). Site Investigation Practice: Assessing BS 5930. Engineering Geology Special Publication No. 2, Geological Society, London.
• Holtz, R.D., Kovacs, W.D. (1981). An Introduction to geotechnical engineering, Prentice Hall.
• Hunt, R.E. (2005). Geotechnical engineering investigation handbook, second edition, Taylor and Francis.
• Iloeje, P.N. (1981). A new geography of Nigeria. Longman Nigeria Limited, Lagos. Kamtchueng, B.T., Onana, V.L., Fantong, W.Y., Ueda, A., Ntouala, R.F.D., Wongolo, M.H.D., Ndongo, G.B., Ze, A.N.,
• Kamgang, V.K.B., Ondoa, J.M. (2015). Geotechnical, chemical and mineralogical evaluation of lateritic soils in humid tropical area (Mfou, Central-Cameroon): Implications for road Construction. International Journal of Geo-Engineering, 6:1 DOI 10.1186/s40703-014-0001-0, 21pp.
• Kennie, T.J.M., Matthews, M.C. (Eds.). (1985). Remote Sensing in Civil Engineering. Surrey University Press, London.
• Kumari, M., Somvanshi, S. (2017). An introduction to remote sensing and its applications (Geoinformatics). Second Edition, S.K. Kataria & Sons, India, 409pp.
• Latham, J.P. (Ed.). (1998). Advances in Aggregates and Armourstone Evaluation. Engineering Geology Special Publication No. 13. Geological Society, London.
• Lillesland, T.M., Kiefer, R.W., Chipman, J. (2003). Remote Sensing and Image Interpretation. Wiley, New York. Martin, F.J., Doyne, H.C. (1927). Laterite and lateritic soils in Sierra Leone. Journal of Agricultural Science, 17: 530-547.
• Mayne, P.W. (2001). Geotechnical site characterization using Cone, piezocone, SPTu, and VST, Civil and Environmental Engineering Department, Georgia Institute of Technology
• Mayne, P.W. (2007). Cone penetration testing: a synthesis of highway practice. Project 20-5. Transportation Research Board, Washington, D.C. NCHRP synthesis 368.
• McNally, G. (1998). Soil and Rock Construction Materials. Spon Press, London. Meyerhof, G.G. (1956). Penetration tests and bearing capacity of cohesionless soils, Journal of the soil mechanics and foundation division, ASCE, Vol. 82, No. SM1, January, pp. 1-19.
• Moss, R.E.S., Seed, R.B., Olsen, R.S. (2006). Normalizing the CPT for overburden stress. J Geotech Geoenviron Eng 132(3):378–387. doi:10.1061/(ASCE)1090-0241(2006)132:3(378).
• Nigeria Geological Survey (1984). Geological Map of Southwestern Nigeria, Geological Survey Department, Ministry of Mines, Power and Steel, Nigeria.
• Nigerian Geological Survey Agency (2006). Geological and Mineral Map of Ondo State, Nigeria.
• Ojo, J.S., Olorunfemi, M.O., Akintorinwa, O.J., Bayode, S., Omosuyi, G.O., Akinluyi, F.O. (2015). Subsoil Competence Characterization of the Akure Metropolis, Southwest Nigeria. Journal of Geography, Environment and Earth Science International, 2015: 3(1): 1-14. Article no.JGEESI.15851. DOI: 10.9734/JGEESI/2015/ 15851
• Olayanju, G.M., Mogaji, K.A., Lim, H.S., Ojo, T.S. (2017). Foundation integrity assessment using integrated geophysical and geotechnical techniques: Case study in crystalline basement complex, southwestern Nigeria. J Geophys Eng 14: 675- 690.
• Osinowo, O.O., Falufosi, M.O. (2018). 3D Electrical Resistivity Imaging (ERI) for subsurface evaluation in preengineering construction site investigation. NRIAG Journal of Astronomy and Geophysics, 1-9pp. https://doi.org/10.1016/j.nrjag.2018.07.001
• Oyedele, K.F., Adeoti, L., Oladele, S., Kamil, A. (2014). Investigation of a Proposed Four Story Building Sites Using Geophysical and Laboratory Engineering Testing Methods in Lagos, Nigeria. International Journal of Scientific Research in Knowledge, 2(2), pp. 83–91.
• Prentice, J.E. (1990). Geology of Construction Materials. Chapman and Hall, London. Robertson, P.K. (1990). Soil classification using the cone penetration test. Can Geotech J 27:151–158.
• Roy, S., Bhalla, S.K. (2017). Role of geotechnical properties of soil on civil engineering structures. Sci Acad Pub 7: 103-109.
• Sabins, F.F. (1996). Remote Sensing – Principles and Interpretation. Second Edition, Freeman and Co., San Francisco.
• Schmertmann, J.H. (1975). Measurement of insitu shear strength, keynote lecture, Proceedings of the conference on in-situ measurement of soil properties, June 1-4, 1975, vol. II, American Society of Civil Engineers.
• Smith, M.R., Collis, L. (Eds.). (2001). Aggregates: Sand, Gravel and Crushed Rock Aggregates. Third Edition. Engineering Geology Special Publication No. 9. Geological Society, London.
• Smith, M.R., (Ed.). (1999). Stone: Building Stone, Rock Fill and Armourstone in Construction. Engineering Geology Special Publication No. 16, Geological Society, London.
• Terzaghi, K., Peck, R.B., Mesri, G. (1996). Soil Mechanics in Engineering Practice, 3rd ed., John Wiley Sons Inc. Tomlinson, M.J. (2001). Foundation Design and Construction. Seventh Edition, Prentice Hall, Harlow, England.
• Upadhyay, A.K. (2015). Soil and Foundation Engineering, Second Edition, S.K. Kataria & Sons New Delhi India.349pp.
• Ward, W.H., Burland, J.B., Gallois, R.W. (1968). Geotechnical assessment of a site at Mundford, Norfolk, for a large proton accelerator. Geotechnique, 18, 399–431
• Winkler, E.M. (1973). Stone: Properties, Durability in Man’s Environment. Springer-Verlag, New York.
• Wright, P.H. (1986). Highway Engineering, Sixth Edition. John Willey and Sons: New York, NY.
• Weltman, A.J., Head, J.M. (1983). Site Investigation Manual. Construction Industry Research and Information Association, Special Publication No. 25, London