A Numerical Analysis of the Effect of Corrugated Surface Profile on Heat Transfer in Turbulent Flow Through a Rectangular Mini-Channel
Abstract
Mini channels have the potential to provide high heat transfer efficiency in a variety of applications. However, due to their small size, higher pressure drop occurs. Therefore, a balance needs to be established between heat transfer improvement and pumping power requirements. In the present study the effect of corrugated surface profile on heat transfer and flow characteristics were numerically investigated under turbulent flow conditions in a rectangular cross-section mini-channel through Computational Fluid Dynamics (CFD) simulations using the ANSYS Fluent 2019 software. The study employed. The mini-channel had a total length of 26 mm, with the left and right side walls consisting of 3 mm straight sections at the inlet and outlet, and a 19 mm corrugated section in the middle while the top and bottom sides are straight end to end. Optimum values for heat transfer and pressure drop were investigated through CFD analyses by varying the profile of the corrugated section of the side walls between 0.5, 1 and 2 mm for air and water fluids. It was determined that the pressure drop for air varied between approximately 850-1250 Pa whereas for water it varied between 1300-1900 Pa. The Nusselt number increased by 3.27% for air, from 12.2 to 12.6, and for water, it increased by 2.17%, from 13.36 to 13.65. Results showed that the corrugated surface improved heat transfer by increasing turbulence and mixing with the flow, but also significantly increases the pressure drop.
Keywords
References
- [1] Pettersen, J., 2004. Flow vaporization of CO2 in microchannel tubes, Experimental thermal and fluid science, 28(2-3), pp.111–121.
- [2] Siddique, W., El-Gabry, L., Shevchuk, I.V., Hushmandi, N.B., and Fransson, T.H., 2012. Flow structure, heat transfer and pressure drop in varying aspect ratio two-pass rectangular smooth channels, Heat Mass Transfer, 48(5), pp.735–748.
- [3] Kandlikar, S.G., and Upadhye, H.R., 2005. Extending the heat flux limit with enhanced microchannels in direct single-phase cooling of computer chips, Semiconductor Thermal Measurement and Management IEEE Twenty First Annual IEEE Symposium.
- [4] Tuckerman, D.B., and Pease, R.F.W., 1981. High-performance heat sinking for VLSI, IEEE Electron device letters, 2(5), pp.126–129.
- [5] Kandlikar, S.G., 2005. Heat transfer mechanisms in microchannels and their engineering applications, J. Heat Transfer, 127(1), pp.8–16.
- [6] Qu, W., and Mudawar, I., 2002. Experimental and numerical study of pressure drop and heat transfer in a single-phase micro-channel heat sink, International Journal of Heat and Mass Transfer, 45(12), pp.2549– 2565.
- [7] Kandlikar, S.G., and Grande, W.J., 2004. Evolution of microchannel flow passages–thermohydraulic performance and fabrication technology, Heat Transfer Engineering, 25(3), pp.3–17.
- [8] Lee, P.S., and Garimella, S.V., 2006. Thermally developing flow and heat transfer in rectangular microchannels of different aspect ratios, International Journal of Heat and Mass Transfer, 49(17-18), pp.3060– 3067.
- [9] Harley, J., Bau, H., Zemel, J.N., and Dominko, V., 20-22 Feb. 1989. "Fluid flow in micron and submicron size channels", in: IEEE Micro Electro Mechanical Systems, , Proceedings, 'An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots', IEEE, pp. 25–28.
- [10] Peng, X.F., and Peterson, G.P., 1996. Convective heat transfer and flow friction for water flow in microchannel structures, International Journal of Heat and Mass Transfer, 39(12), pp.2599–2608.