INVESTIGATION OF WEAR WEIGHT LOSS IN ALUMINUM MATRIX COMPOSITES

Yıl 2020, Cilt: 3 Sayı: 2, 160 - 170, 31.12.2020

Engin Ergül Halil Kurt Murat Oduncuoğlu Can Çivi Gökhan Eyici

Öz

In many industrial applications, hardness and wear come to the fore, especially in materials in contact with each other. It is almost impossible to completely prevent abrasion loss in materials in contact with each other. However, it may be preferable to minimize this rate with various methods or to ensure the abrasion of the material with lower economic value. New and up-to-date materials are needed to minimize wear loss, which is one of the most important mechanisms in engineering applications. It is important to use engineering materials with high friction resistance, especially in places where there is friction. In this study, Al2024 was used as matrix material. A mixture of 50% by weight of Magnesium oxide (MgO) with an average diameter of <40 nm and a 50% multi-walled carbon nanotube (MWCNT) 1.5 µm in length and 9.5 nm in diameter were used as reinforcement. It is produced by composite mixing casting method. Mechanical properties, hardness analysis and abrasive wear behavior of composites have been investigated at different sliding distances (250m-500m-1000m) under 2N and 5N loads.

Anahtar Kelimeler

Wear, Composite, CNT, MgO, Al2024

Kaynakça

• [1] T. W. Clyne and P. J. Withers, An Introduction to Metal Matrix Composites. Cambridge University Press, 1993.
• [2] A. R. Riahi and A. T. Alpas, “The role of tribo-layers on the sliding wear behavior of graphitic aluminum matrix composites,” Wear, vol. 250–251, no. PART 2, pp. 1396–1407, Oct. 2001, doi: 10.1016/s0043-1648(01)00796-7.
• [3] Z. F. Zhang, L. C. Zhang, and Y. W. Mai, “Particle effects on friction and wear of aluminium matrix composites,” J. Mater. Sci., vol. 30, no. 23, pp. 5999–6004, Dec. 1995, doi: 10.1007/BF01151519.
• [4] H. Abdizadeh, P. H. Vajargah, and M. A. Baghchesara, “Fabrication of MgO nanoparticulates reinforced aluminum matrix composites using stir-casting method,” Kov. Mater., vol. 53, no. 5, pp. 319–326, 2015, doi: 10.4149/km-2015-5-319.
• [5] L. A. Batista, M. D. V. Felisberto, L. S. Silva, T. H. R. da Cunha, and E. M. Mazzer, “Influence of multi-walled carbon nanotubes reinforcements on hardness and abrasion behaviour of porous Al-matrix composite processed by cold pressing and sintering,” J. Alloys Compd., vol. 791, pp. 96–99, Jun. 2019, doi: 10.1016/j.jallcom.2019.03.265.
• [6] M. Em Pul, R. Çalin, and F. Gül, “Investigation of abrasion in Al-MgO metal matrix composites,” Mater. Res. Bull., vol. 60, pp. 634–639, Dec. 2014, doi: 10.1016/j.materresbull.2014.09.040.
• [7] S. Kumar, A. Sharma, R. Arora, and O. P. Pandey, “The microstructure and wear behaviour of garnet particle reinforced Al matrix composites,” J. Mater. Res. Technol., vol. 8, no. 6, pp. 5443–5455, Nov. 2019, doi: 10.1016/j.jmrt.2019.09.012.
• [8] H. Chang, J. Binner, and R. Higginson, “Dry sliding wear behaviour of Al(Mg)/Al2O3 interpenetrating composites produced by a pressureless infiltration technique,” Wear, vol. 268, no. 1, pp. 166–171, Jan. 2010, doi: 10.1016/j.wear.2009.07.014.
• [9] G. G. Sozhamannan, M. Mohamed Yusuf, G. Aravind, G. Kumaresan, K. Velmurugan, and V. S. K. Venkatachalapathy, “Effect of Applied Load on the Wear Performance of 6061 Al/ Nano Ticp/ Gr Hybrid Composites,” in Materials Today: Proceedings, Jan. 2018, vol. 5, no. 2, pp. 6489–6496, doi: 10.1016/j.matpr.2017.12.262.