ANALYSIS OF ANNUAL ENERGY REQUIREMENT OF A RESIDENTIAL HOUSE WITH TS825 AND ASHRAE HEAT BALANCE METHODS

Yıl 2017, Cilt: 1 Sayı: 1, 5 - 10, 15.05.2017

Kaan Yaman Gökhan Arslan

https://doi.org/10.31127/tuje.316503

Cited By: 1

Öz

Energy efficiency in buildings is an important up-to-date topic. For that reason, accurate calculation of heating and cooling loads is essential. In this study, heating and cooling loads of a residential house were determined by using national standards for different climatic zones Mersin, İstanbul, Ankara, Erzincan, and Erzurum. Calculations were performed by using the TS825 method that is based on national mandatory heat insulation standard TS825 and EnergyPlus software that is based on heat balance method. Heating loads obtained from simulations were compared on the monthly and annual basis. The absolute deviation between methods results was obtained in the range of 1.9 % to 39.5 %. The highest deviation was in Mersin where represents the 1st region and the lowest deviation was in Ankara where represents the 3rd region. Since TS825 method has not feature to simulate cooling load, annual cooling load calculated by using EnergyPlus software was 128.2 kWh/m²y for Mersin, 70.7 kWh/m²y for Istanbul, 44.9 kWh/m²y for Ankara, 49.0 kWh/m²y for Erzincan and 26.7 kWh/m²y for Erzurum. Insufficiency of the TS825 method was examined in detail.

Anahtar Kelimeler

Heating Load, Cooling Load, TS825, Heat Balance Method, EnergyPlus

Kaynakça

• ASHRAE Guideline 14 (2014). Measurement of energy, demand, and water savings, American Society of Heating, Ventilating, and Air Conditioning Engineers, Atlanta, GA, USA.
• Harish V. S. K. V. and Kumar, A. (2016). “A review on modeling and simulation of building energy systems.” Renewable Sustainable Energy Reviews, Vol. 56, pp. 1272-92. doi:10.1016/j.rser.2015.12.040.
• Keskin, T. (2010). Binalar sektörü mevcut durum değerlendirmesi raporu. http://iklim.cob.gov.tr/iklim/Files/Enerji_Sektoru_Mevcut_Durum_Degerlendirmesi_Raporu.pdf [Accessed 27.05.2017].
• Kürekçi A., Bardakçı, A. T., Çubuk, H. and Emanet, Ö. (2012) “Türkiye’nin tüm illeri için optimum yalıtım kalınlığının belirlenmesi.” Tesisat Mühendisliği Dergisi, Vol. 131, pp. 5-21.
• Özkan, D. B., Onan, C. and Erdem, S. (2009). “Effect of insulation material thickness on thermal insulation.” Sigma - Journal of Engineering and Natural Sciences, Vol. 27, pp. 190-196.
• Perez-Lombard, L., Ortiz, J. and Pout, C. (2008). “A review on buildings energy consumption information.” Energy and Buildings, Vol. 40, No. 3, pp. 394–398.
• Stadler, M., Firestone, R., Curtil, D. and Marnay, C. (2006). “On-site generation simulation with EnergyPlus for commercial buildings.” ACEEE Summer Study on Energy Efficiency in Buildings, pp. 242-254.
• The Republic of Turkey, Ministry of Energy and Natural Resources, http://www.eigm.gov.tr/tr-TR/DengeTablolari/Denge-Tablolari [Accessed 28.02.2016].
• The Republic of Turkey, Ministry of Energy and Natural Resources, http://www.eie.gov.tr/ [Accessed 08.03.2016].
• TS EN ISO 14683 (2009). Thermal bridges in building construction-linear thermal transmittance-simplified method and default values, Turkish Standard Institution, Ankara, Turkey.
• TS 825 (2013). Thermal insulation requirements for buildings, Turkish Standards Institution, Ankara, Turkey.
• U.S. Department of Energy, http://www.energy.gov/, Washington, USA, [Accessed 23.05.2017].
• Walton G. N. (1983). “Thermal Analysis Research Program Reference Manual”. National Bureau of Standards.