Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube

Mustafa Caner; Ertan Buyruk

doi:10.17678/beuscitech.1818795

Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube

Abstract

The study involved a series of experiments to examine the heat transfer behaviour of shell-and-tube heat exchangers with a helically coiled corrugated tube. Experimental investigations were conducted to analyse the performance of the heat exchangers, with a focus on the impact of tube- and shell-side flow rates, as well as shell inlet temperature, on effectiveness. Throughout the experiments, the tube inlet water temperature was kept at 20 °C, whereas the shell inlet temperature was set to 50, 60 or 70 °C. The tube flow rate was set to 1, 2 or 3 L/min, while the shell flow rate was set to 2, 3 or 4 L/min. A total of 27 tests were performed with these combinations. The results show that effectiveness increases significantly with an increase in the shell side flow rate and hot inlet water temperature, whereas an increase in the tube side flow rate reduces effectiveness. The highest effectiveness value (ε = 0.603) was obtained at a shell side flow rate of 4 L/min, a tube side flow rate of 1 L/min and a shell side inlet temperature of 70 °C. The maximum heat transfer was measured as 3290 W at an inlet temperature of 70 °C and a flow rate of 4 L/min on the shell side and 3 L/min on the tube side. The experimental data obtained provide a reliable basis for validating numerical models and designing highly efficient, compact heat exchangers.

Keywords

Supporting Institution

Sivas Cumhuriyet University Scientific Research Projects (CUBAP)

Project Number

M-2022-828

References

V. Kumar, B. Faizee, M. Mridha, and K. D. P. Nigam, “Numerical studies of a tube-in-tube helically coiled heat exchanger,” Chem. Eng. Process, vol. 47, no. 12, pp. 2287–2295, Nov. 2008, doi: 10.1016/j.cep.2008.01.001.
C. Shen, C. Cirone, L. Yang, Y. Jiang, and X. Wang, “Characteristics of fouling development in shell-and-tube heat exchanger: Effects of velocity and installation location,” Int. J. Heat Mass Transf. vol. 77, pp. 439–448, Oct. 2014, doi: 10.1016/j.ijheatmasstransfer.2014.05.031.
A. Zachár, “Investigation of natural convection induced outer side heat transfer rate of coiled-tube heat exchangers,” Int J Heat Mass Transf, vol. 55, no. 25–26, pp. 7892–7901, Dec. 2012, doi: 10.1016/j.ijheatmasstransfer.2012.08.014.
E. Izadpanah, A. Zarei, S. Akhavan, and M. Babaie Rabiee, “An experimental investigation of natural convection heat transfer from a helically coiled heat exchanger,” Int. J. Refrig, vol. 93, pp. 38–46, Sept. 2018, doi: 10.1016/j.ijrefrig.2018.06.008.
A. Sheeba, C. M. Abhijith, and M. Jose Prakash, “Experimental and numerical investigations on the heat transfer and flow characteristics of a helical coil heat exchanger,” Int. J. Refrig, vol. 99, pp. 490–497, Mar. 2019, doi: 10.1016/j.ijrefrig.2018.12.002.
B. K. Hardik, P. K. Baburajan, and S. V. Prabhu, “Local heat transfer coefficient in helical coils with single phase flow,” Int J Heat Mass Transf, vol. 89, pp. 522–538, Oct. 2015, doi: 10.1016/j.ijheatmasstransfer.2015.05.069.
C. Zhang, D. Wang, S. Xiang, Y. Han, and X. Peng, “Numerical investigation of heat transfer and pressure drop in helically coiled tube with spherical corrugation,” Int J Heat Mass Transf, vol. 113, pp. 332–341, Oct. 2017, doi: 10.1016/j.ijheatmasstransfer.2017.05.108.
L. Zheng, Y. Xie, and D. Zhang, “Numerical investigation on heat transfer and flow characteristics in helically coiled mini-tubes equipped with dimples,” Int J Heat Mass Transf, vol. 126, pp. 544–570, Nov. 2018, doi: 10.1016/j.ijheatmasstransfer.2018.05.111.

J. Wang, S. S. Hashemi, S. Alahgholi, M. Mehri, M. Safarzadeh, and A. Alimoradi, “Analysis of Exergy and energy in shell and helically coiled finned tube heat exchangers and design optimization,” Int. J. Refrig, vol. 94, pp. 11–23, Oct. 2018, doi: 10.1016/j.ijrefrig.2018.07.028.
M. Moawed, “Experimental study of forced convection from helical coiled tubes with different parameters,” Energy Convers Manag, vol. 52, no. 2, pp. 1150–1156, Feb. 2011, doi: 10.1016/j.enconman.2010.09.009.
A. Alimoradi and F. Veysi, “Prediction of heat transfer coefficients of shell and coiled tube heat exchangers using numerical method and experimental validation,” Int. J. Therm. Sci., vol. 107, pp. 196–208, Sept. 2016, doi: 10.1016/j.ijthermalsci.2016.04.010.
M. Sepehr, S. S. Hashemi, M. Rahjoo, V. Farhangmehr, and A. Alimoradi, “Prediction of heat transfer, pressure drop and entropy generation in shell and helically coiled finned tube heat exchangers,” Chem. Eng. Res. Des., vol. 134, pp. 277–291, June 2018, doi: 10.1016/j.cherd.2018.04.010.
D. G. Prabhanjan, G. S. V. Raghavan, and T. J. Rennie, “Comparison of heat transfer rates between a straight tube heat exchanger and a helically coiled heat exchanger,” Int. Commun. Heat Mass Transf., vol. 29, no. 2, pp. 185–191, Feb. 2002, doi: 10.1016/S0735-1933(02)00309-3.
A. A. Rabienataj Darzi, M. Abuzadeh, and M. Omidi, “Numerical investigation on thermal performance of coiled tube with helical corrugated wall,” Int. J. Therm. Sci., vol. 161, p. 106759, Mar. 2021, doi: 10.1016/j.ijthermalsci.2020.106759.
Ş. M. Kırkar, "Düz ve helisel borularda koruge yüzeylerin kullanımının ısı geçişi karakteristiklerine etkisinin sayısal olarak incelenmesi," M.S. thesis, Fen Bilimleri Enstitüsü, Yıldız Teknik Üniversitesi, İstanbul, Türkiye, 2020
B. Gong, S. Yu, Y. Li, P. Lu, C. Zhang, and X. Wang, “Numerical study and mechanism analysis of heat transfer in a helical tube enhanced by sinusoidal pulsating flow combined with an annular corrugated structure,” J. Mech. Sci. Technol., vol. 38, no. 10, pp. 5685–5695, Oct. 2024, doi: 10.1007/s12206-024-0938-7.
H. Chen et al., “Thermal/ exergy and economic efficiency analysis of circumferentially corrugated helical tube with constant wall temperature,” Case Stud. Therm. Eng., vol. 23, p. 100803, Feb. 2021, doi: 10.1016/j.csite.2020.100803.
H. Al-Gburi, A. A. Mohammed, and A. H. Al-Abbas, “Experimental study of the thermal performance of corrugated helically coiled tube-in-tube heat exchanger,” Front. Heat Mass Transf., vol. 20, Mar. 2023, doi: 10.5098/hmt.20.17.
O. Heydari, M. Miansari, H. Arasteh, and D. Toghraie, “Optimizing the hydrothermal performance of helically corrugated coiled tube heat exchangers using Taguchi’s empirical method: energy and exergy analysis,” J Therm Anal Calorim, vol. 145, no. 5, pp. 2741–2752, Sept. 2021, doi: 10.1007/s10973-020-09808-3.
M. A. Talib, F. M. K. AL-Fatlwe, A. S. Baqir, and A. H. Ali, “Optimization and evaluation of Overall Heat Transfer Coefficient of helical coil tube heat exchanger with air injection,” JSEA, vol. 6, no. 1, pp. 43–54, 2024.
J. Wu, Y. Zhu, C. Gao, and D. Ding, “Numerical research of an internal and external-corrugated tube-in-tube helical coil heat exchanger,” Energy Sources Recovery Util. Environ. Eff., vol. 46, no. 1, pp. 3581–3600, Dec. 2024, doi: 10.1080/15567036.2024.2319724.
Ö. Karabey and A. Akkuş, “Sürünme Test Cihazı Tasarımı ve İmalatı,” Bitlis Eren Üniversitesi Fen Bilimleri Dergisi, vol. 11, no. 1, pp. 369–376, 2022. https://doi.org/10.17798/bitlisfen.1030964
P. S. Srinivasan, S. S. Nandapurkar, and F. A. Holland, "Friction factors for coils," Trans. Inst. Chem. Eng., vol. 48, no. 4–6, pp. T156–T+, 1970.
P. Mishra and S. N. Gupta, “Momentum Transfer in Curved Pipes. 1. Newtonian Fluids,” Industrial & Engineering Chemistry Process Design and Development, vol. 18, no. 1, pp. 130–137, Jan. 1979, doi: 10.1021/i260069a017.
A. Cioncolini and L. Santini, “An experimental investigation regarding the laminar to turbulent flow transition in helically coiled pipes,” Exp Therm Fluid Sci, vol. 30, no. 4, pp. 367–380, Mar. 2006, doi: 10.1016/j.expthermflusci.2005.08.005.
M. S. El-Genk and T. M. Schriener, “A Review and Correlations for Convection Heat Transfer and Pressure Losses in Toroidal and Helically Coiled Tubes,” Heat Trans. Eng., vol. 38, no. 5, pp. 447–474, Mar. 2017, doi: 10.1080/01457632.2016.1194693.
Y. A. Cengel and A. J. Ghajar, Heat and Mass Transfer: Fundamentals and Applications, 5th ed. New York, NY, USA: McGraw-Hill Education, 2014.
A. Alimoradi, “Study of thermal effectiveness and its relation with NTU in shell and helically coiled tube heat exchangers,” Case Stud. Therm. Eng., vol. 9, pp. 100–107, Mar. 2017, doi: 10.1016/j.csite.2017.01.003.
H. M. Maghrabie, M. Attalla, and A. A. A. Mohsen, “Performance of a shell and helically coiled tube heat exchanger with variable inclination angle: Experimental study and sensitivity analysis,” Int. J. Therm. Sci., vol. 164, p. 106869, June 2021, doi: 10.1016/j.ijthermalsci.2021.106869.
A. D. Tuncer, A. Sözen, A. Khanlari, E. Y. Gürbüz, and H. İ. Variyenli, “Analysis of thermal performance of an improved shell and helically coiled heat exchanger,” Appl Therm Eng., vol. 184, p. 116272, Feb. 2021, doi: 10.1016/j.applthermaleng.2020.116272.
J. P. Holman, Experimental Methods for Engineers, 8th ed. New York, NY, USA: McGraw-Hill, 2012, p. 739.

Details

Primary Language

English

Subjects

Experimental Methods in Fluid Flow, Heat and Mass Transfer

Journal Section

Research Article

Authors

Mustafa Caner ^*
0000-0002-3674-7881
Türkiye

Ertan Buyruk
0000-0002-6539-7614
Türkiye

Publication Date

December 31, 2025

Submission Date

November 6, 2025

Acceptance Date

December 27, 2025

Published in Issue

Year 2025 Volume: 15 Number: 2

DOI

https://doi.org/10.17678/beuscitech.1818795

IZ

https://izlik.org/JA85GE37MN

Cite

RIS / Bibtex

APA

Caner, M., & Buyruk, E. (2025). Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube. Bitlis Eren University Journal of Science and Technology, 15(2), 195-213. https://doi.org/10.17678/beuscitech.1818795

AMA

1.Caner M, Buyruk E. Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube. Bitlis Eren University Journal of Science and Technology. 2025;15(2):195-213. doi:10.17678/beuscitech.1818795

Chicago

Caner, Mustafa, and Ertan Buyruk. 2025. “Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger With Helically Coiled Corrugated Tube”. Bitlis Eren University Journal of Science and Technology 15 (2): 195-213. https://doi.org/10.17678/beuscitech.1818795.

EndNote

Caner M, Buyruk E (December 1, 2025) Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube. Bitlis Eren University Journal of Science and Technology 15 2 195–213.

IEEE

[1]M. Caner and E. Buyruk, “Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube”, Bitlis Eren University Journal of Science and Technology, vol. 15, no. 2, pp. 195–213, Dec. 2025, doi: 10.17678/beuscitech.1818795.

ISNAD

Caner, Mustafa - Buyruk, Ertan. “Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger With Helically Coiled Corrugated Tube”. Bitlis Eren University Journal of Science and Technology 15/2 (December 1, 2025): 195-213. https://doi.org/10.17678/beuscitech.1818795.

JAMA

1.Caner M, Buyruk E. Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube. Bitlis Eren University Journal of Science and Technology. 2025;15:195–213.

MLA

Caner, Mustafa, and Ertan Buyruk. “Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger With Helically Coiled Corrugated Tube”. Bitlis Eren University Journal of Science and Technology, vol. 15, no. 2, Dec. 2025, pp. 195-13, doi:10.17678/beuscitech.1818795.

Vancouver

1.Mustafa Caner, Ertan Buyruk. Experimental Investigation of the Performance of a Shell and Tube Heat Exchanger with Helically Coiled Corrugated Tube. Bitlis Eren University Journal of Science and Technology. 2025 Dec. 1;15(2):195-213. doi:10.17678/beuscitech.1818795