Experimental research of the influence of fiber laser machining parameters on HAZ width in AISI 4140 steels

Year 2024, Volume: 15 Issue: 4, 873 - 880

Mehmet Şükrü Adin

https://doi.org/10.24012/dumf.1563430

Abstract

In present day, laser beam machining technology attracts great attention due to its cost-effectiveness, high machining quality, mass manufacturing velocity and broad areas of applicability throughout different manufacturing industries. However, intensive researches are required since many materials with different properties (chemical and mechanical) are used in the manufacturing industries; and there is need for high quality machining through newly developed laser technologies. In this context, in this experimental research, unlike most studies in the literature, an investigation was carried out on heat affected zone (HAZ) occurring in AISI 4140 steel machined by laser beam in different cutting geometries (triangle, square and circle cutting). In the present study, when the average HAZ widths calculated according to the laser cutting geometries were examined, it was understood that the highest average HAZ width (579 μm) was obtained in the triangle cutting geometry and the lowest average HAZ width (369 μm) was obtained in the circle cutting geometry. What is more, when the average HAZ widths obtained according to laser cutting geometries were compared, it was observed that the average HAZ widths of the specimens cut in triangle geometry were 31.61% and 56.93% larger than the specimens cut in square and circle cutting geometries, respectively. Furthermore, it was found that as the laser power increased, the HAZ widths were negatively affected (i.e., HAZ widths increased), but as the cutting speed increased, the HAZ widths were positively affected (i.e., HAZ widths decreased). From the ANOVA analyses, it was found that the cutting geometry (with a rate of 51.32%) was the most pivotal parameter influencing the HAZ width. When the regression analysis results (based on quadratic regression models) were checked, it was understood that R2 value had a very high rate (96.79%) as desired. Thus, from these results, it was understood that the model developed to predict the HAZ width values has a high success rate and reliability.

Keywords

Fiber laser machining, Laser cutting, Heat affected zone, HAZ width, AISI 4140, Taguchi DOE

Ethical Statement

Dear Editor; I confirm that the work described has not been published previously, that it is not under consideration for publication elsewhere, that its publication is approved and that, if accepted, it will not be published elsewhere in the same form, in English or in any other language, without the written consent of the Publisher. I hope that the manuscript is suitable for the publication in an exclusive journal, Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi. Yours sincerely, with best regards. *Asst. Prof. Dr. Mehmet Şükrü Adin1 *Corresponding Author 1*Batman University, Besiri OSB Vocational School, Batman, 72060, Turkey *Mehmet Şükrü Adin (M.Ş. Adin, ORCID ID: 0000-0002-2307-9669 ) E-mail: [e-mail] Tel.: [phone] WhatsApp: [phone]

References

• [1] M. Kardan, N. Levichev, S. Castagne, and J. R. Duflou, "Dynamic beam shaping requirements for fiber laser cutting of thick plates," Journal of Manufacturing Processes, vol. 103, pp. 287-297, 2023.
• [2] U. Çaydaş and A. Hasçalık, "Use of the grey relational analysis to determine optimum laser cutting parameters with multi-performance characteristics," Optics & laser technology, vol. 40, no. 7, pp. 987-994, 2008.
• [3] W. M. Steen and J. Mazumder, "Laser material processing," Springer science & business media, Fourth Edition, pp. 1-577, 2010.
• [4] C. Guo and S. C. Singh, Handbook of Laser Technology and Applications: Lasers Applications: Materials Processing and Spectroscopy (Volume Three). CRC Press, 2021.
• [5] E. Kannatey-Asibu, "Principles of Laser Materials Processing: Developments and Applications," John Wiley & Sons, Inc., pp. 1-611, 2023.
• [6] J. Lawrence, "Advances in laser materials processing: technology, research and applications," Woodhead Publishing, vol. 2, pp. 1-802, 2017.
• [7] G. C. Rodrigues and J. Duflou, "Effects of different polarization strategies on laser cutting with direct diode lasers," Physics Procedia, vol. 83, pp. 302-309, 2016.
• [8] G. C. Rodrigues, M. Cuypers, E. F. Sichani, K. Kellens, and J. Duflou, "Laser cutting with direct diode laser," Physics Procedia, vol. 41, pp. 558-565, 2013.
• [9] W. D. Callister and D. G. Rethwisch, Materials science and engineering: an introduction, 9 ed. Wiley, New York, 2014.
• [10] V.-H. Nguyen, T.-T. Le, A.-T. Nguyen, X.-T. Hoang, N.-T. Nguyen, and N.-K. Nguyen, "Optimization of milling conditions for AISI 4140 steel using an integrated machine learning-multi objective optimization-multi criteria decision making framework," Measurement, p. 115837, 2024.
• [11] D. C. Montgomery, Design and analysis of experiments, Ninth ed. John wiley & sons, 2017.
• [12] G. Taguchi, System of experimental design, quality resources (New York, USA). 1987.
• [13] J. Vora et al., "Experimental investigations and Pareto optimization of fiber laser cutting process of Ti6Al4V," Metals, vol. 11, no. 9, p. 1461, 2021.
• [14] S. Tam, L. E. Lim, and K. Quek, "Application of Taguchi methods in the optimization of the laser-cutting process," Journal of Materials Processing Technology, vol. 29, no. 1-3, pp. 63-74, 1992.
• [15] P. Patel, S. Sheth, and T. Patel, "Experimental analysis and ANN modelling of HAZ in laser cutting of glass fibre reinforced plastic composites," Procedia Technology, vol. 23, pp. 406-413, 2016.
• [16] J. Powell, S. Al-Mashikhi, A. Kaplan, and K. Voisey, "Fibre laser cutting of thin section mild steel: An explanation of the ‘striation free’effect," Optics and Lasers in Engineering, vol. 49, no. 8, pp. 1069-1075, 2011.
• [17] Y. Wang et al., "Finite element simulation and experimental verification of laser machining of nitinol tubes," Optics & Laser Technology, vol. 181, p. 111672, 2025.
• [18] S. Al-Mashikhi, J. Powell, A. Kaplan, and K. Voisey, "Heat affected zones and oxidation marks in fiber laser–oxygen cutting of mild steel," Journal of laser applications, vol. 23, no. 4, 2011.
• [19] Y. Liu and S. Zhang, "Improving the cutting process and quality of thick plates with high-power fiber laser," Optical Fiber Technology, vol. 83, p. 103684, 2024.
• [20] M. Ş. Adin, "Effects of cutting geometries and cutting parameters on the surface roughness and kerf width of X60 steel machined by laser beam," Journal of Materials Engineering and Performance, pp. 1-20, 2024.
• [21] A. İpekçi and K. Argun, "Surface Roughness Performance of Cu Electrode on Hardened AISI 4140 Steels in EDM Process," Journal of Chinese Society of Mechanical Engineers, vol. 43, no. 4, pp. 355-362, 2022.
• [22] K. Krishnaiah and P. Shahabudeen, "Applied design of experiments and Taguchi methods," PHI Learning Pvt. Ltd., pp. 1-371, 2012.
• [23] A. İpekçi, and K. Argun, "Experimental investigation and optimization of machining parameters of deep cryogenically treated and tempered steels in electrical discharge machining process," Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, vol. 236, no. 5, pp. 1927-1935, 2022.
• [24] M. Şeremet, "Experimental and statistical investigation of surface roughness and vibration during finish turning of AISI 4140 steel workpiece under cooling method," Surf. Rev. Lett., vol. 28, no. 10, p. 2150092, 2021.
• [25] V. K. Tiwary, P. Arunkumar, and V. R. Malik, "Investigations on the effect of Spin Friction Welding parameters on joint strength and cylindricity of similar/dissimilar Material Extrusion (MEX) 3D printed parts," Journal of Advanced Joining Processes, vol. 9, p. 100208, 2024.