GURSON-TVERGAARD-NEEDLEMAN (GTN) PARAMETERS OF DP STEELS WITH DIFFERENT ROLLING DIRECTIONS WERE DETERMINED AND INVESTIGATED AT DIFFERENT STRAIN RATES

Year 2022, , 71 - 83, 15.12.2022

Labinot Topilla , Serkan Toros

https://doi.org/10.55696/ejset.1113577

Abstract

Dual Phase steels are high-strength and well-formability steels, which are widely used in the automobile industry. However, based on their microstructural observations, the shapes, orientations, and directions of the grains of these two steels are different and vary depending on the degree of observation. Therefore, the objective of this research was to compare the stress and strain distribution at different strain rates of standard specimens and cut at different rolling directions of DP steels, namely DP600 and DP800 steels. Besides, in this study, the finite element modeling method is used through optimization to determine the GTN fracture failure, constitutive and nucleation parameters of the mentioned steels based on their rolling directions and strain rates. The experimental and numerical simulation results are also compared, and they are in good agreement.

Keywords

DP steels. Experimental, Optimizations, Simulations, GTN parameters.

References

• A. S. Podder, D. Bhattacharjee, and R. K. Ray, “Effect of martensite on the mechanical behavior of ferrite-bainite dual phase steels,” ISIJ Int., vol. 47, no. 7, pp. 1058–1064, 2007, doi: 10.2355/isijinternational.47.1058.
• C. M. Gómora, R. R. Ambriz, C. J. García, I. Ruíz-López, and D. Jaramillo, “Dissimilar Dual Phase-Low Carbon Steel Joints by the GMAW Process Subjected to Impact Load,” Metals (Basel)., vol. 12, no. 3, pp. 1–18, 2022, doi: 10.3390/met12030404.
• C. Sébastien Y.P.Allain, Irina Pushkareva, JulienTeixeira, Mohamed Gouné, “Dual-Phase Steels: The First Family of Advanced High Strength Steels,” Encycl. Mater. Met. Alloy., 2022.
• S. Kang and H. Kwon: s, No TitleMetall. Tran. 1987.
• “www.arcelormittal.com.” Access date 21.07.2022.
• M. Achouri, G. Germain, P. Dal Santo, and D. Saidane, “Experimental characterization and numerical modeling of micromechanical damage under different stress states,” Mater. Des., vol. 50, pp. 207–222, 2013, doi: 10.1016/j.matdes.2013.02.075.
• M. Feucht, D.-Z. Sun, T. Erhart, and T. Frank, “Recent development and applications of the Gurson model,” in LS-DYNA Anwenderforum, 2006.
• F. Feng et al., “Application of a GTN damage model predicting the fracture of 5052-O aluminum alloy high-speed electromagnetic impaction,” Metals (Basel)., vol. 8, no. 10, 2018, doi: 10.3390/met8100761.
• K. L. Nielsen and V. Tvergaard, “Ductile shear failure or plug failure of spot welds modelled by modified Gurson model,” Eng. Fract. Mech., vol. 77, no. 7, pp. 1031–1047, 2010, doi: 10.1016/j.engfracmech.2010.02.031.
• R. O. Santos et al., “Damage identification parameters of dual-phase 600-800 steels based on experimental void analysis and finite element simulations,” J. Mater. Res. Technol., vol. 8, no. 1, pp. 644–659, 2019, doi: 10.1016/j.jmrt.2018.04.017.
• M. H. Miloud, I. Zidane, and M. Mendas, “Coupled identification of the hardening behavior laws and Gurson– Tvergaard–Needleman damage parameters - validation on tear test of 12NiCr6 CT specimen,” Frat. ed Integrita Strutt., vol. 13, no. 49, pp. 630–642, 2019, doi: 10.3221/IGF-ESIS.49.57.
• F. Andrade and M. Feucht, “A comparison of damage and failure models for the failure prediction of dual-phase steels,” 2017.
• C. Netrasiri and S. Suranuntchai, “Damage curve determination of dual phase steel based on gtn mode-l failure criteria,” Int. J. Mech. Eng. Robot. Res., 2016, doi: 10.18178/ijmerr.5.4.268-271.
• Y. Bao and T. Wierzbicki, “On fracture locus in the equivalent strain and stress triaxiality space,” Int. J. Mech. Sci., 2004, doi: 10.1016/j.ijmecsci.2004.02.006.
• H. Chalal and F. Abed-Meraim, “Determination of forming limit diagrams based on ductile damage models and necking criteria,” Lat. Am. J. Solids Struct., vol. 14, no. 10, pp. 1872–1892, 2017, doi: 10.1590/1679-78253481.
• M. Achouri, G. Germain, P. Dal Santo, and D. Saidane, “Numerical integration of an advanced Gurson model for shear loading: Application to the blanking process,” Comput. Mater. Sci., vol. 72, pp. 62–67, 2013, doi: 10.1016/j.commatsci.2013.01.035.
• N. STANDER, W. ROUX, T. GOEL, T. EGGLESTON, and K. E. N. CRAIG, LS-OPT User ’ s Manual: A DESIGN OPTIMIZATION AND PROBABILISTIC ANALYSIS TOOL, no. February. 2012.
• N. A. Tvergaard, V, “Analysis of the cup-cone fracture in a round tensile bar,” 1984.
• M. Springmann and M. Kuna, “Determination of ductile damage parameters by local deformation fields: Measurement and simulation,” Arch. Appl. Mech., vol. 75, no. 10–12, pp. 775–797, 2006, doi: 10.1007/s00419-006-0033-9.