Fatigue analysis of 3D-printed polymer materials under various manufacturing parameters utilizing poisson regression method and ANOVA

Murat Horasan; İsmail Saraç

doi:10.26701/ems.1717687

Fatigue analysis of 3D-printed polymer materials under various manufacturing parameters utilizing poisson regression method and ANOVA

Abstract

In this study, we conducted a statistical evaluation of the experimental results from a prior investigation by the authors concerning the fatigue behavior of 3-Dimensional (3D) printed Polylactic Acid (PLA) materials. Stress versus number of cycles (S-N) curves for the sample types were derived using the Poisson regression method. Within the scope of the statistical analysis, we performed average effect plots and an analysis of variance. At the conclusion of the study, we clearly observed the impact of printing parameters on the fatigue of 3D printed PLA materials, especially at low stress amplitude levels. At high stress amplitude values, the effect of printing parameters on the fatigue behavior of 3D printed PLA parts was limited. The analysis revealed that the stress level was the most influential factor determining the number of cycles to failure. While the production parameters of the PLA specimen, such as raster angle and printing speed, significantly impacted the results at a low stress level of 9.13 MPa, their effect was much less pronounced at a higher stress amplitude of 18.25 MPa, where variations in the number of cycles to failure among different specimen types were minimal. The analysis determined that the optimal parameter combination for 3D printed PLA fatigue specimens was a printing speed of 20 mm/s, a raster angle of 30°, and a stress amplitude of 9.13 MPa. According to the analysis of variance results, the parameter that most significantly influenced fatigue life was the stress level, contributing 54.93%. Raster angle and printing speed contributed 14.52% and 4.19%, respectively. The Poisson regression method proved to be an effective tool for plotting S-N graphs.

Keywords

References

Harding, A., Pramanik, A., Basak, A.K., Prakash, C., & Shankar, S. (2023). Application of additive manufacturing in the biomedical field-A review. Annals of 3D Printed Medicine, 10, 100110. https://doi.org/10.1016/j.stlm.2023.100110.
Salifu, S., Desai, D., Ogunbiyi, O., & Mwale, K. (2022). Recent development in the additive manufacturing of polymer-based composites for automotive structures—a review. The International Journal of Advanced Manufacturing Technology, 119, 6877–6891. https://doi.org/10.1007/s00170-021-08569-z.
Singh, S., & Ramakrishna, S. (2017). Biomedical applications of additive manufacturing: Present and future. Current Opinion in Biomedical Engineering, 2, 105–115. https://doi.org/10.1016/j.cobme.2017.05.006.
Tepylo, N., Huang, X., & Patnaik, P.C. (2019). Laser-Based Additive Manufacturing Technologies for Aerospace Applications. Advanced Engineering Materials, 21, 1900617. https://doi.org/10.1002/adem.201900617.
Trevisan, F., Calignano, F., Aversa, A., Marchese, G., Lombardi, M., Biamino, S., Ugues, D., & Manfredi, D. (2018). Additive manufacturing of titanium alloys in the biomedical field: processes, properties and applications. Journal of Applied Biomaterials & Functional Materials, 16(2), 57–67. https://doi.org/10.5301/jabfm.5000371.
Wazeer, A., Das, A., Sinha, A., Inaba, K., Ziyi, S., & Karmakar, A. (2023). Additive manufacturing in biomedical field: a critical review on fabrication method, materials used, applications, challenges, and future prospects. Progress in Additive Manufacturing, 8, 857–889. https://doi.org/10.1007/s40964-022-00362-y.
Adin, M. Ş., & Kam, M. (2024). An overview of post-processing of fused deposition modelling 3D printed products. Post-Processing of Parts and Components Fabricated by Fused Deposition Modeling, 1-10.
Mallikarjuna, B., Bhargav, P., Hiremath, S., Jayachristiyan, K.G., & Jayanth, N. (2025). A review on the melt extrusion-based fused deposition modeling (FDM): background, materials, process parameters and military applications. International Journal on Interactive Design and Manufacturing, 19, 651–665. https://doi.org/10.1007/s12008-023-01354-0.

Sapkota, A., Ghimire, S.K., & Adanur, S. (2024). A review on fused deposition modeling (FDM)-based additive manufacturing (AM) methods, materials and applications for flexible fabric structures. Journal of Industrial Textiles, 54. https://doi.org/10.1177/15280837241282110.
Solomon, I.J., Sevvel, P., & Gunasekaran, J. (2021). A review on the various processing parameters in FDM. Materials Today Proceedings, 37(2), 509–514. https://doi.org/10.1016/j.matpr.2020.05.484.
Doshi, M., Mahale, A., Singh, S.K., & Deshmukh, S. (2022). Printing parameters and materials affecting mechanical properties of FDM-3D printed Parts: Perspective and prospects. Materials Today Proceedings, 50(5), 2269–2275. https://doi.org/10.1016/j.matpr.2021.10.003.
Kristiawan, R.B., Imaduddin, F., Ariawan, D., Ubaidillah, & Arifin, Z. (2021). A review on the fused deposition modeling (FDM) 3D printing: Filament processing, materials, and printing parameters. Open Engineering, 11(1), 639–649. https://doi.org/10.1515/eng-2021-0063.
Ahmad, M.N., & Yahya, A. (2023). Effects of 3D Printing Parameters on Mechanical Properties of ABS Samples. Designs, 7(6), 136. https://doi.org/10.3390/designs7060136.
Hsueh, M.-H., Lai, C.-J., Wang, S.-H., Zeng, Y.-S., Hsieh, C.-H., Pan, C.-Y., & Huang, W.-C. (2021). Effect of Printing Parameters on the Thermal and Mechanical Properties of 3D-Printed PLA and PETG, Using Fused Deposition Modeling. Polymers, 13(11), 1758. https://doi.org/10.3390/polym13111758.
Lokesh, N., Praveena, B.A., Reddy, J.S., Vasu, V.K., & Vijaykumar, S. (2022). Evaluation on effect of printing process parameter through Taguchi approach on mechanical properties of 3D printed PLA specimens using FDM at constant printing temperature. Materials Today Proceedings, 52(3), 1288–1293. https://doi.org/10.1016/j.matpr.2021.11.054.
Popescu, D., Zapciu, A., Amza, C., Baciu, F., & Marinescu, R. (2018). FDM process parameters influence over the mechanical properties of polymer specimens: A review. Polymer Testing, 69, 157–166. https://doi.org/10.1016/j.polymertesting.2018.05.020.
Sagias, V.D., Giannakopoulos, K.I., & Stergiou, C. (2018). Mechanical properties of 3D printed polymer specimens. Procedia Structural Integrity, 10, 85–90. https://doi.org/10.1016/j.prostr.2018.09.013.
Afrose, M.F., Masood, S.H., Iovenitti, P., Nikzad, M., & Sbarski, I. (2016). Effects of part build orientations on fatigue behaviour of FDM-processed PLA material. Progress in Additive Manufacturing, 1, 21–28. https://doi.org/10.1007/s40964-015-0002-3.
Saraç, İ., & Horasan, M. (2024). The Torsional Characterization of 3D-Printed Polylactic Acid Parts With Alternating Additive Manufacturing Parameters. Polymers for Advanced Technologies, 35, e6642. https://doi.org/10.1002/pat.6642.
Azadi, M., Dadashi, A., Dezianian, S., Kianifar, M., Torkaman, S., & Chiyani, M. (2021). High-cycle bending fatigue properties of additive-manufactured ABS and PLA polymers fabricated by fused deposition modeling 3D-printing. Forces in Mechanics, 3, 100016, 2021. https://doi.org/10.1016/j.finmec.2021.100016.
Dadashi, A., & Azadi, M. (2023). Experimental bending fatigue data of additive-manufactured PLA biomaterial fabricated by different 3D printing parameters. Progress in Additive Manufacturing, 8, 255–263. https://doi.org/10.1007/s40964-022-00327-1.
Akhoundi, B., & Behravesh, A.H. (2019). Effect of Filling Pattern on the Tensile and Flexural Mechanical Properties of FDM 3D Printed Products. Experimental Mechanics, 59, 883–897. https://doi.org/10.1007/s11340-018-00467-y.
Horasan, M., & Sarac, I. (2024). The fatigue responses of 3D‐printed polylactic acid (PLA) parts with varying raster angles and printing speeds. Fatigue & Fracture of Engineering Materials & Structures, 47(10): 3693-3706. https://doi.org/10.1111/ffe.14406.
Adin M. Ş. (2024). Experimental research of the influence of fiber laser machining parameters on HAZ width in AISI 4140 steels, Dicle University Journal of Engineering, 15(4), 873–880. https://doi.org/10.24012/dumf.1563430.
Adin, M. Ş. (2024). Investigation of the effects of laser power and gas pressure on the top and bottom HAZ widths in AISI 1040 steels. Journal of Science, Technology and Engineering Research, 5(2), 163-175. https://doi.org/10.53525/jster.1583593

Details

Primary Language

English

Subjects

Solid Mechanics , Material Design and Behaviors

Journal Section

Research Article

Authors

Murat Horasan ^*
0000-0002-7870-1486
Türkiye

İsmail Saraç
0000-0001-8438-2744
Türkiye

Publication Date

September 20, 2025

Submission Date

June 11, 2025

Acceptance Date

August 4, 2025

Published in Issue

Year 2025 Volume: 9 Number: 3

DOI

https://doi.org/10.26701/ems.1717687

IZ

https://izlik.org/JA29RM94FN

Cite

RIS / Bibtex

APA

Horasan, M., & Saraç, İ. (2025). Fatigue analysis of 3D-printed polymer materials under various manufacturing parameters utilizing poisson regression method and ANOVA. European Mechanical Science, 9(3), 246-254. https://doi.org/10.26701/ems.1717687