Production of Ti-Fe Based MgAl2O4 Composite Material by Pressureless Infiltration Method

Abstract

In spite of their high temperature and corrosion resistance, ceramics show a brittle nature under applied loads and this limits their usage areas. In order to compensate the weakness of ceramics with metals, which have high ductility, the production of ceramic-metal composite materials has been recently started. In the present study, a ceramic-metal composite material was produced by means of pressureless infiltration method using spinel oxide (MgAl2O4) and Ti-Fe alloy. Atmospheric conditions, Ti-Fe/MgAl2O4 ratio, infiltration temperature and time were chosen as an experimental parameter. The experimenral results showed that a passivating oxide layer on the surface of the Ti-Fe alloy was observed in ambient atmosphere at 1600 °C for 120 minutes and therefore no reaction took place between the spinel and Ti-Fe alloy. Whereas, the Ti-Fe alloy was successfully infiltrated under argon atmosphere at 1550 and 1600 °C for 30, 60 and 120 minutes. The infiltrated Ti-Fe composites were characterized using SEM equipped with EDS. The hardness values of the Ti-Fe/MgAl2O4 composite increased up to 22.5 % Ti-Fe amount and further increase in the Ti-Fe amount led to a decrease in the hardness.

Keywords

• Titanium alloys, pressurelles infiltration, cermet, spinel

References

1. S. Neralla, D. Kumar, S. Yarmolenko and J. Sankar, Mechanical properties of nanocomposite metal-ceramic thin films, Composites Part B, 35 (2004)157-162.
2. G. KrauB, L. Kübler and E. Trentini, Preparation and properties of pressureless infiltrated SiC and AIN particulate reinforced metal-ceramic composites based on bronze and iron alloys, Materials Science and Engineering A, 337 (2002) 315-322.
3. K. Lemster, T. Graule and J. Kuebler, Processing and microstructure of metal matrix composite prepared by pressureless Ti-activated infiltration using Fe-base and Ni-base alloys, Materials Science and Engineering A, 393 (2005) 229-238.
4. L. M. Peng, J. W. Caob, K. Nodac, and K.S. Hand, Mechanical properties of ceramic–metal composites by pressure infiltration of metal into porous ceramics, Materials Science and Engineering A, 374, (2004) 1– 9.
5. R. Subramanian, J. H. Schneibel, FeAl-TiC cermets- melt infiltration processing and mechanical properties, Materials Science and Engineering A, 239–240 (1997) 633–639.
6. A. Contreras, V. H. Lopez, E. Bedolla, Scripta Materialia 51 (2004) 249-53.
7. M. Bilen, A. Mergen, M. Gürü and A. Alıcılar, Infiltration of Al alloys into MgAl2O under different atmospheres, Key Engineering Materials, Vols.264- 268 (2004) pp. 1795-1798.
8. M. Gürü, M. Korçak, S. Tekeli and A. Güral, “Processing of Zinc-Based MgAl2O4 composite and Effect of Fly Ash Addition”, Key Engineering Materials, June (2006) pp. 1203-1206 (in press).

9. N. A. Travitzky, E.Y. Gutmanas, and N. Claussen, Mechanical
10. fabricated by pressureless infiltration technique, of
11. Materials Letters, 33, (1997), 47-50.
12. composites [10] N. A. Travitzky and A. Shlayen, Microstructure and mechanical properties of Al2O3 : Cu–O composites fabricated by pressureless infiltration technique, Materials Science and Engineering A, 244, (1998), 154-160.
13. C. Kurnaz, Production of saffir fiber reinforced Zn- Al (ZA 12) based metal matrix composites using infiltration technique and study of their properties, Materials Science and Engineering A, 346, (2003), 108-115.
14. A. P. Tomsia, E. Saiz, S. Foppiano and W. Moberly Chan, Synthesis and processing of ceramic- metal composites by reactive metal penetration, Composites Part A, 30 (1999), 399-403.