HİBRİD TİP BAĞLANTI UYGULANMIŞ TERMOPLASTİK KOMPOZİT PLAKALARDAKİ ISIL KAYMA GERİLMELERİNİN BELİRLENMESİ

Year 2015, Volume: 1 Issue: 1, 13 - 17, 07.04.2015

Faruk Şen Mehmet Alkan

https://doi.org/10.22531/muglajsci.209993

Abstract

Bu çalışmanın amacı hibrid tip bağlantı uygulanmış termoplastik kompozit plakalardaki ısıl kayma gerilmelerinin belirlenmesidir. Hibrid bağlantı yapıştırıcı ve iki paralel pim uygulaması şeklinde tasarlanmıştır. Problemin çizimi ve çözümü ANSYS yazılımı kullanılarak gerçekleştirilmiştir. Bu yüzden çözümlerde sonlu elemanlar metodu kullanılmıştır. Hibrid bağlantının modellenmesi üç boyutlu olarak yapılmıştır. Tasarlanan yapıdaki ısıl gerilmeler uygulanan uniform sıcaklık yükleri nedeniyle meydana gelmiştir. Elde edilen sonuçlar, ısıl gerilmelerin uniform sıcaklık artışına çok önemli oranda bağlı olduğunu göstermiştir. Kısaca, ısıl kayma gerilmeleri, sıcaklık yükündeki artışa bağlı olarak artmıştır

Keywords

FEM, ANSYS, Kayma gerilmesi, Isıl gerilme, Hibrid bağlantı

DETERMINATION OF THERMAL SHEAR STRESSES ON TERMOPLASTIC COMPOSITE ADHERENTS JOINED HYBRID TYPE

Abstract

This paper aims to determine of thermal shear stresses on thermoplastic adherents which are joined by hybrid type. It is designed both adhesive and two parallel pins. Both plotting and solving of this problem were done using ANSYS software. Therefore solutions were performed with finite element methods (FEM). Modeling of hybrid joint was established as three dimensional. Thermal stresses were caused to apply uniform thermal loads on designed structure. Determined results pointed out that thermal shear stresses were strictly affected of increasing uniform thermal loads. Briefly, their values were increased by increasing of thermal loadings.

Keywords

FEM, ANSYS, Shear stress, Thermal Stress, Hybrid joint

References

• Potter, K. An Inroduction to Composite Materials, Chapman & Hall, London, 1997.
• Schwartz, M.M. Composite Materials Handbook, Mc Graw Hill Inc, USA, 1984.
• Callister, W.D. Materials Science and Engineering an Introduction, John Wiley & Sons Inc., USA, 2003.
• Arslan, N. and Celik, M. “Thermoplastic matrix plates in elasto-plastic finite element analysis”, Journal of Reinforced Plastics and Composites, 20, 1191-1204, 2001.
• Apalak, M.K., Aldas, K., and Sen, F., “Thermal non-linear stresses in an adhesively bonded and laser-spot welded single-lap joint during laser-metal interaction”, Journal of Materials Processing Technology, 142, 1-19, 2003.
• Sen, F. “The estimation of elasto-plastic thermal and residual stresses in a thermoplastic composite disc under uniform temperature effect”, Journal of Reinforced Plastics and Composites. 25, 1485-1498, 2006.
• Rastogi, N., Soni, S.R. and Nagar, A. “Thermal stresses in aluminum-to-composite double-lap bonded joints”, Advances in Engineering Software, 29, 273-281, 1998.
• Wu, P.S. and Sun, C.T. “Modeling bearing failure initiation in pin-contact of composite laminates”, Mechanics of Materials, 29, 325-335, 1998.
• Camanho, P.P. and Lambert, M. “A design methodology for mechanically fastened joints in laminated composite materials”, Composites Science and Technology, 66, 3004- 3020, 2006.
• Sen, F. and Sayman, O. “Failure response of two serial bolted aluminum sandwich composite plates”, Journal of Sandwich Structures and Materials, 12, 551-568, 2010.
• Ataş, A., Sen, F., Arslan, N. “Failure analysis of laminated composite plates with two parallel pin-loaded holes”. Journal of Reinforced Plastics and Composites, 28, 1265-1276, 2009.
• Pakdil, M., Sen, F., Sayman, O., Benli, S. “The effect of preload on failure response of glass-epoxy laminated composite bolted-joints with clearance”, Journal of Reinforced Plastics and Composites, 26, 1239-1252, 2007.
• Sen, F. 2006. “The estimation of elasto-plastic thermal and residual stresses in a thermoplastic composite disc under uniform temperature effect”, Journal of Reinforced Plastics and Composites, 25, 1485-1498, 2006.