BibTex RIS Cite

Ti-6Al-4V ALA?IMININ FREZELENMESYNDE Y?LEME PARAMETRELERYNYN TAGUCHI METODU KULLANARAK OPTYMYZASYONU

Year 2011, Volume: 6 Issue: 1, 428 - 440, 01.02.2011

Mustafa Günay Alaattin Kaçal Yakup Turgut

Abstract

Bu çaly?ma Ti-6Al-4V ala?ymynyn karbür takymlarla kuru ?artlarda yüzey frezelenmesinde i?leme parametrelerinin kesme kuvvetleri ve yüzey pürüzlülü?ü üzerindeki etkilerini ve optimizasyonunu göstermektedir. Deneysel düzen Taguchi metodu kullanylarak belirlenmi?tir. Optimum i?leme parametreleri kombinasyonu sinyal-gürültü orany analizi kullanylarak elde edilmi?tir. Deney sonuçlaryna göre, bile?ke kesme kuvveti ve yüzey pürüzlülü?ü ilerlemenin artmasyyla artarken kesme hyzynyn artmasyyla azalmy?tyr. Hem bile?ke kesme kuvveti (FR) hemde yüzey pürüzlülü?ü (Ra) için optimum kesme ?artlary 180 m/dak kesme hyzynda ve 250 mm/dak ilerlemede elde edilmi?tir.

Keywords

Ti-6Al-4V Ala?ymy Yüzey Frezeleme Yüzey Kesme Kuvvetleri Taguchi Metodu

OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD

Year 2011, Volume: 6 Issue: 1, 428 - 440, 01.02.2011

Mustafa Günay Alaattin Kaçal Yakup Turgut

Abstract

This paper presents optimizing and effect of machining parameters on the cutting forces and surface roughness during face milling of Ti-6Al-4V alloy with carbide tools under dry conditions. Experimental setup was determined by using Taguchi design method. The optimum machining parameter combination was acquired by using signal-to-noise (S/N) ratio analysis. According to experimental results, resultant cutting forces and surface roughness increased with an increase in feed rate, whereas decreased with increase in cutting speed. Optimum machining conditions for the both resultant cutting forces (FR) and surface roughness (Ra) were obtained at cutting speed of 180 m/min and feed rate of 250 mm/min.

Keywords

Ti-6Al-4V Alloy Face Milling Surface Roughness Cutting Forces Taguchi Method

There are 0 citations in total.

Details

Primary Language Turkish
Journal Section Computer Engineering
Authors

Mustafa Günay This is me

Alaattin Kaçal This is me

Yakup Turgut This is me

Publication Date February 1, 2011
Published in Issue Year 2011 Volume: 6 Issue: 1

Cite

APA Günay, M., Kaçal, A., & Turgut, Y. (2011). OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences, 6(1), 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046
AMA Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. February 2011;6(1):428-440. doi:10.12739/nwsaes.v6i1.5000067046
Chicago Günay, Mustafa, Alaattin Kaçal, and Yakup Turgut. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6, no. 1 (February 2011): 428-40. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
EndNote Günay M, Kaçal A, Turgut Y (February 1, 2011) OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences 6 1 428–440.
IEEE M. Günay, A. Kaçal, and Y. Turgut, “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”, Engineering Sciences, vol. 6, no. 1, pp. 428–440, 2011, doi: 10.12739/nwsaes.v6i1.5000067046.
ISNAD Günay, Mustafa et al. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences 6/1 (February 2011), 428-440. https://doi.org/10.12739/nwsaes.v6i1.5000067046.
JAMA Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6:428–440.
MLA Günay, Mustafa et al. “OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD”. Engineering Sciences, vol. 6, no. 1, 2011, pp. 428-40, doi:10.12739/nwsaes.v6i1.5000067046.
Vancouver Günay M, Kaçal A, Turgut Y. OPTIMIZATION OF MACHINING PARAMETERS IN MILLING OF Ti-6Al-4V ALLOY USING TAGUCHI METHOD. Engineering Sciences. 2011;6(1):428-40.