OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING

Kürşad Oğuz Oskay; Bilal Demirel

OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING

Abstract

NiCrAl composite coatings were obtained by electro-deposition under direct current (DC) conditions from a Watt’s bath containing suspended Cr, Al particles. Mathematical models were developed to simulate the electroplated composite coating. The models allow composition of the coatings to be predicted. The predicted values obtained were close to the experimental values, indicating the suitability of the models. The prediction made using Response Surface Method (RSM) was also supported by SEM photos. Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.

Keywords

References

[1] Aruna S. T., Roy S., Sharma A., Savitha G., and Grips V. K. W. (2014) Cost-effective wear and oxidation resistant electrodeposited Ni – pumice coating, Surf. Coat. Technol., vol. 251, pp. 201–209.
[2] Masoudi M., Hashim M., Kamari H. M., and Salit M. S. (2012) Fabrication and characterization of Ni–SiC–Cr nanocomposite coatings, Appl. Nanosci., vol. 3, no. 4, pp. 357–362.
[3] Liu H. and Chen W. (2005) Electrodeposited Ni-Al composite coatings with high Al content by sediment co-deposition, Surf. Coatings Technol., vol. 191, no. 2–3, pp. 341–350.
[4] Borkar T. and Harimkar S. P. (2011) Effect of electrodeposition conditions and reinforcement content on microstructure and tribological properties of nickel composite coatings, Surf. Coatings Technol., vol. 205, no. 17–18, pp. 4124–4134.
[5] Vaezi M. R., Sadrnezhaad S. K., and Nikzad L. (2008) Electrodeposition of Ni–SiC nano-composite coatings and evaluation of wear and corrosion resistance and electroplating characteristics, Colloids Surfaces A Physicochem. Eng. Asp., vol. 315, no. 1–3, pp. 176–182.
[6] Srivastava M., Siju, Balaraju J. N., and Ravisankar B. (2015) Development and High Temperature Property Evaluation of Ni-Co-Cr-Al Composite Electroforms, J. Mater. Eng. Perform., vol. 24, no. 5, pp. 1937–1944.
[7] Ul-Hamid A., Dafalla H., Al-Yousef F., and Mohammed A. I. (2014) Microstructural study of NiCrAlY electrodeposits, Prot. Met. Phys. Chem. Surfaces, vol. 50, no. 5, pp. 679–687.
[8] Bahamirian M. (2013) An Investigation on Effect of Bond Coat Replacement on Hot Corrosion Properties of Thermal Barrier Coatings, Iran. J. Mater. Sci. Eng., vol. 10, no. 3, pp. 12–21.

[9] Bates B. L., Zhang L. Z., and Zhang,Y. (2015) Electrodeposition of Ni matrix composite coatings with embedded CrAlY particles, Surf. Eng., vol. 31, no. 3, pp. 202–208.
[10] Haynes J. A., Ferber M. K., and Porter W. D. (2000) Thermal Cycling Behavior of Plasma-Sprayed Thermal Barrier Coatings with Various MCrAIX Bond Coats, J. Therm. Spray Technol., vol. 9, no. March, pp. 38–48.
[11] Zhu C., Li P., and Wu X. Y. (2015) A study of the diffusion and pre-oxidation treatment on the formation of Al2O3 ceramic scale on NiCrAlY bond-coat during initial oxidation process, Ceram. Int., vol. 42, pp. 7708–7716,.
[12] Ajdelsztajn L., Tang F., Kim G. E., Provenzano V., and Schoenung J. M. (2005) Synthesis and Oxidation Behavior of Nanocrystalline MCrAlY Bond Coatings, J. Therm. Spray Technol., vol. 14, no. 1, pp. 23–30.
[13] Şahin Y. and Öksüz K. E. (2016) Tribological behavior of Al2O3/Al composite coating on γ-TiAl at elevated temperature, Mater. Test., vol. 58, no. 5, pp. 453–461.
[14] Aslan N. (2008) Multi-objective optimization of some process parameters of a multi-gravity separator for chromite concentration, Sep. Purif. Technol., vol. 64, no. 2, pp. 237–241.
[15] Zhao L.-C. et al. (2012) Response surface modeling and optimization of accelerated solvent extraction of four lignans from fructus schisandrae. Molecules, vol. 17, no. 4, pp. 3618–29.
[16] Lee H. K., Lee H.-Y., and Jeon J.-M. (2007) Codeposition of micro- and nano-sized SiC particles in the nickel matrix composite coatings obtained by electroplating, Surf. Coatings Technol. vol. 201, no. 8, pp. 4711–4717.
[17] Kim S. K. and Yoo H. J. (1998) Formation of bilayer Ni–SiC composite coatings by electrodeposition. Surf. Coatings Technol., vol. 108, pp. 564–569.

Details

Primary Language

English

Subjects

Engineering

Journal Section

Research Article

Authors

Kürşad Oğuz Oskay This is me
0000-0003-4026-867X
Türkiye

Bilal Demirel This is me
Türkiye

Publication Date

September 1, 2018

Submission Date

July 25, 2017

Acceptance Date

February 20, 2018

Published in Issue

Year 2018 Volume: 36 Number: 3

IZ

https://izlik.org/JA28HJ86ER

Cite

RIS / Bibtex

APA

Oskay, K. O., & Demirel, B. (2018). OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. Sigma Journal of Engineering and Natural Sciences, 36(3), 795-802. https://izlik.org/JA28HJ86ER

AMA

1.Oskay KO, Demirel B. OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. SIGMA. 2018;36(3):795-802. https://izlik.org/JA28HJ86ER

Chicago

Oskay, Kürşad Oğuz, and Bilal Demirel. 2018. “OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING”. Sigma Journal of Engineering and Natural Sciences 36 (3): 795-802. https://izlik.org/JA28HJ86ER.

EndNote

Oskay KO, Demirel B (September 1, 2018) OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. Sigma Journal of Engineering and Natural Sciences 36 3 795–802.

IEEE

[1]K. O. Oskay and B. Demirel, “OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING”, SIGMA, vol. 36, no. 3, pp. 795–802, Sept. 2018, [Online]. Available: https://izlik.org/JA28HJ86ER

ISNAD

Oskay, Kürşad Oğuz - Demirel, Bilal. “OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING”. Sigma Journal of Engineering and Natural Sciences 36/3 (September 1, 2018): 795-802. https://izlik.org/JA28HJ86ER.

JAMA

1.Oskay KO, Demirel B. OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. SIGMA. 2018;36:795–802.

MLA

Oskay, Kürşad Oğuz, and Bilal Demirel. “OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING”. Sigma Journal of Engineering and Natural Sciences, vol. 36, no. 3, Sept. 2018, pp. 795-02, https://izlik.org/JA28HJ86ER.

Vancouver

1.Kürşad Oğuz Oskay, Bilal Demirel. OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. SIGMA [Internet]. 2018 Sep. 1;36(3):795-802. Available from: https://izlik.org/JA28HJ86ER