OPTICAL NUMERICAL INVESTIGATION OF A SOLAR POWER PLANT OF PARABOLIC TROUGH COLLECTORS

Abstract

Going forward towards developing and improving renewable energies in Algeria is one of the main objectives of this study, especially, solar energy that is an exceptional and continuous source of energy. Algerian Sahara has a large area suitable for agriculture, but not connected to the electricity network. Therefore, the construction of solar power plants based on the solar energy concentration has been proposed for the electricity production, which is exploited in the rest of the economic sector of the Algerian state. Through the study conducted under real weather data for the day March 16th, 2018, an optical characterization of a solar power plant of parabolic trough concentrator has been convoyed in El-Oued region, Algeria. The geometrical and the optical characteristics of studied solar collector have been determined, such as the optical efficiency, the local concentration ratio, the cosine effect of the incidence angle, the optical losses at the ends of the receiver tube, the shading effect, the blocking effect, and the coefficient of incidence angle modifier and intercept factor. MATLAB code has been used as a program for numerical programming. Of the most important results obtained, it was found that the optical efficiency has exceeded 77.22 %. As for the local concentration ratio, its maximum value is equal to 116.30 in the lower part of the receiver tube at the peripheral receiver angles “β=91° and 269°", while the minimum values of this important coefficient were recorded at the top of the receiver tube.

Keywords

• Solar Energy
• Power Plants
• Parabolic Trough Collector
• Optical Investigation
• Numerical Smulation

References

1. [1] Ghodbane M, Boumeddane B, Said Z, Bellos E. A numerical simulation of a linear Fresnel solar reflector directed to produce steam for the power plant. Journal of Cleaner Production 2019; 231:494-508. https://doi.org/10.1016/j.jclepro.2019.05.201.
2. [2] Ghodbane M, Benmenine D, Khechekhouche A, Boumeddane B. Brief on Solar Concentrators: Differences and Applications. Instrumentation Mesure Metrologie 2020;19(5):371-378. https://dx.doi.org/10.18280/i2m.190507.
3. [3] Girard A, Roberts C, Simon F, Ordoñez J. Solar electricity production and taxi electrical vehicle conversion in Chile. Journal of Cleaner Production 2019; 210: 1261-1269. https://doi.org/10.016/j.jclepro.2018.11.092.
4. [4] Settino J, Sant T, Micallef C, Farrugia M, Staines CS, Licari J, Micallef A. Overview of solar technologies for electricity, heating and cooling production. Renewable and Sustainable Energy Reviews 2018; 90: 892-909. https://doi.org/10.1016/j.rser.2018.03.112.
5. [5] Bouguila A, Said R. Optimization of a Small Scale Concentrated Solar Power Plant Using Rankine Cycle. Journal of Thermal Engineering 2020; 6(3): 268-81. https://dx.doi.org/10.18186/thermal.711287.
6. [6] Taner T, Dalkilic AS. A Feasibility Study of Solar Energy - Economic Analysis from Aksaray, Turkey. Journal of Thermal Engineering 2019; 5(1): 25-30. https:/dx.doi.org/10.18186/thermal.505498.
7. [7] Ghodbane M, Bellos E, Said Z, Boumeddane B, Khechekhouche A, Sheikholeslami M, Ali ZM. Energy, Financial and Environmental investigation of a direct steam production power plant driven by linear Fresnel solar reflectors. Journal of Solar Energy Engineering 2021; 143(2): 021008. https://doi.org/10.1115/1.4048158.
8. [8] Mazzeo D. Solar and wind assisted heat pump to meet the building air conditioning and electric energy demand in the presence of an electric vehicle charging station and battery storage. Journal of Cleaner Production 2019; 213: 1228-1250. https://doi.org/10.1016/j.jclepro.2018.12.212.

9. [9] Ghodbane M, Boumeddane B, Hussein AK. Performance Analysis of a Solar-Driven Ejector Air Conditioning System Under El-Oued Climatic Conditions, Algeria. Journal of Thermal Engineering 2021; 7(1): 172-89. https://dx.doi.org/10.18186/thermal.847334.
10. [10] Ghodbane M. Étude et optimisation des performances d'une machine de climatisation a éjecteur reliée à un concentrateur solaire. Université Saad Dahlab de Blida 1. 2017.
11. [11] Ghodbane M, Boumeddane B, Khechekhouche A, Benmenine D. Study of a solar air conditioning system with ejector. International Journal of Energetica (IJECA) 2020; 5(1): 14-21. https://dx.doi.org/10.47238/ijeca.v5i1.115.
12. [12] Delgado-Marín JP, García FV, García-Cascales JR. Use of a predictive control to improve the energy efficiency in indoor swimming pools using solar thermal energy. Solar Energy 2019; 179: 380-390. https://doi.org/10.1016/j.solener.2019.01.004.
13. [13] Ghodbane M, Boumeddane B, Moummi N, Largot S, Berkane H. Study and numerical simulation of solar system for air heating. Journal of Fundamental and Applied Sciences 2016; 8(1): 41-60, http://dx.doi.org/10.4314/jfas.v8i1.3.
14. [14] Singh J, Singh R, Bhushan B. Thermo-Hydraulic Performance of Solar Air Heater Duct having Triangular Protrusions as Roughness Geometry. Journal of Thermal Engineering 2015; 1(7): 607-620. https://dx.doi.org/10.18186/jte.01332.
15. [15] Yıldırım C. Theoretical Investigation of a Solar Air Heater Roughened by Ribs and Grooves. Journal of Thermal Engineering 2018; 4(1): 1702-1712. https:/dx.doi.org/10.18186/journal-of-thermal-engineering.365713.
16. [16] Ghodbane M, Boumeddane B, Said N. A linear Fresnel reflector as a solar system for heating water: theoretical and experimental study. Case Studies in Thermal Engineering 2016; 8(C): 176-186, http://dx.doi.org/10.1016/j.csite.2016.06.006.
17. [17] Endale A. Analysis of Status, Potential and Economic Significance of Solar Water Heating System in Ethiopia. Renewable Energy 2019; 132: 1167-1176. https://doi.org/10.016/j.renene.2018.08.094.
18. [18] Kerme E, Kaneesamkandi Z. Performance Analysis and Design of Liquid Based Solar Heating System. Journal of Thermal Engineering 2015; 1(5):182-191. https://dx.doi.org/10.18186/jte.02359.
19. [19] Bellos E, Said Z, Tzivanidis C. The use of nanofluids in solar concentrating technologies: A comprehensive review. Journal of Cleaner Production 2018; 196: 84-99. https://doi.org/10.1016/j.jclepro.2018.06.048.
20. [20] Loni R, Asli-Ardeh EA, Ghobadian B, Ahmadi MH, Bellos E. GMDH modeling and experimental investigation of thermal performance enhancement of hemispherical cavity receiver using MWCNT/oil nanofluid. Solar Energy 2018; 171: 790–803. https://doi.org/10.1016/j.solener.2018.07.003.
21. [21] Rizi AP, Ashrafzadeh A, Ramezani A. A financial comparative study of solar and regular irrigation pumps: Case studies in eastern and southern Iran. Renewable Energy 138: 1096-1103. https://doi.org/10.16/j.renene.2019.02.026.
22. [22] Powell JW, Welsh JM, Farquharson R. Investment analysis of solar energy in a hybrid diesel irrigation pumping system in New South Wales, Australia. Journal of Cleaner Production 2019;224: 444-454. https://doi.org/10.1016/j.jclepro.2019.03.071.
23. [23] Costa BA, Lemos JM, Guillot E. Solar furnace temperature control with active cooling. Solar Energy 2018;159: 66-77. http://dx.doi.org/10.1016/j.solener.2017.10.017.
24. [24] Indora S, Kandpal TC. Financial appraisal of using Scheffler dish for steam based institutional solar cooking in India. Renewable Energy 2019; 135: 1400-1411. https://doi.org/10.016/j.renene.2018.09.067.
25. [25] Ahmed FE, Hashaikeh R, Hilal N. Solar powered desalination – Technology, energy and future outlook. Desalination 2019; 453:54-76. https://doi.org/10.1016/j.desal.2018.12.002.
26. [26] Ghasemi A, Hashemian N, Noorpoor A, Heidarnejad P. Exergy Based Optimization of a Biomass and Solar Fuelled CCHP Hybrid Seawater Desalination Plant. Journal of Thermal Engineering 2017; 3(1):1034-1043. https:/dx.doi.org/10.18186/thermal.290251.
27. [27] Stegou-Sagia A, Fragkou DV. Thin Layer Drying Modeling of Apples and Apricots in A Solar-Assisted Drying System. Journal of Thermal Engineering 2018; 4(1):1680-1691. https:/dx.doi.org/10.18186/journal-of-thermal-engineering.364909.
28. [28] Attia MEH, Driss Z, Ghodbane M, Hussein AK, Rout SK, Li D, editors. Experimental Study of the Temperature Distribution Inside an Indirect Solar Dryer Chamber. Advances in Air Conditioning and Refrigeration; 2021; Singapore: Springer Singapore.
29. [29] Pulido-Iparraguirre D, Valenzuela L, Aguilera JJ, Fernández-Garcíaa A. Optimized design of a Linear Fresnel reflector for solar process heat applications. Renewable Energy 2019; 131: 1089-1106. https://doi.org/10.16/j.renene.2018.08.018.
30. [30] Farjana SH, Huda N, Parvez-Mahmud MA, Saidur R. Solar process heat in industrial systems – A global review. Renewable and Sustainable Energy Reviews 2018; 82: 2270-2286. http://dx.doi.org/10.1016/j.rser.2017.08.065.
31. [31] Bellos E, Korres D, Tzivanidis C, Antonopoulos KA. Design, simulation and optimization of a compound parabolic collector. Sustainable Energy Technologies and Assessments 2016; 16: 53-63. https://doi.org/10.1016/j.seta.2016.04.005.
32. [32] Korres D, Bellos E, Tzivanidis C. Investigation of a nanofluid-based compound parabolic trough solar collector under laminar flow conditions. Applied Thermal Engineering 2019; 149: 366–376. https://doi.org/10.1016/j.applthermaleng.2018.12.077.
33. [33] Said Z, Saidur R, Rahim NA. Energy and exergy analysis of a flat plate solar collector using different sizes of aluminium oxide based nanofluid. Journal of Cleaner Production 2016; 133: 518-530. https://doi.org/10.1016/j.jclepro.2016.05.178.
34. [34] Said Z, Saidur R, Sabiha MA, Hepbasli A, Rahim NA. Energy and exergy efficiency of a flat plate solar collector using pH treated Al2O3 nanofluid. Journal of Cleaner Production 2016; 112: 3915-3926. https://doi.org/10.1016/j.jclepro.2015.07.115.
35. [35] Said Z, Saidur R, Sabiha MA, Rahim NA, Anisur MR. Thermophysical properties of Single Wall Carbon Nanotubes and its effect on exergy efficiency of a flat plate solar collector. Solar Energy 2015; 115: 757-769. https://doi.org/10.1016/j.solener.2015.02.037.
36. [36] Kalogirou SA. Solar thermal collectors and applications. Progress in Energy and Combustion Science 2004; 30(3): 231-95. https://doi.org/10.1016/j.pecs.2004.02.001. [37] Said Z, Ghodbane M, Hachicha AA, Boumeddane B. Optical performance assessment of a small experimental prototype of linear Fresnel reflector. Case Studies in Thermal Engineering 2019: 100541. https://doi.org/10.1016/j.csite.2019.
37. [38] Ghodbane M, Boumeddane B, Said N. Design and experimental study of a solar system for heating water utilizing a linear Fresnel reflector. Journal of Fundamental and Applied Sciences 2016; 8(3): 804-825, http://dx.doi.org/10.4314/jfas.v8i3.8.
38. [39] Ghodbane M, Bellos E, Said Z, Boumeddane B, Hussein AK, Kolsi L. Evaluating energy efficiency and economic effect of heat transfer in copper tube for small solar linear Fresnel reflector. Journal of Thermal Analysis and Calorimetry 2020. https://doi.org/10.1007/s10973-020-09384-6.
39. [40] Kasaeian A, Loni R, Asli-Ardeh EA, Ghobadian B, Shahverdi K. Thermal Evaluation of Cavity Receiver using Water/PG as the Solar Working Fluid. Journal of Thermal Engineering 2019; 5(5): 446-455. https://dx.doi.org/10.18186/thermal.624341.
40. [41] Kasaeian A, Loni R, Asli-Ardeh EA, Ghobadian B, Shahverdi K. Comparison Study of Air and Thermal Oil Application in a Solar Cavity Receiver. Journal of Thermal Engineering 2019; 5(6): 221-229. https://dx.doi.org/10.18186/thermal.654628.
41. [42] Ghodbane M, Boumeddane B, Hussein AK, Ali HM. Thermal numerical investigation of a small parabolic trough collector under desert climatic conditions Journal of Thermal Engineering 2021.
42. [43] Yettou F. Receiver Temperature Maps of Parabolic Collector Used for Solar Food Cooking Application in Algeria. Journal of Thermal Engineering 2018; 4(1): 1656-1667. https:/dx.doi.org/10.18186/journal-of-thermal-engineering.364866.
43. [44] Benmenine D, Ghodbane M, Soudani ME, Abdelouahed H, Massiv A, Elsharif N. A small parabolic trough collector as a solar water heater: an experimental study in Ouargla region, Algeria. International Journal of Energetica (IJECA) 2020; 5(2):1-6. https://dx.doi.org/10.47238/ijeca.v5i2.141.
44. [45] Hussein AK, Ghodbane M, Said Z, Ward RS. The Effect of the Baffle Length on the Natural Convection in an Enclosure Filled with Different Nanofluids. Journal of Thermal Analysis and Calorimetry 2020. https://doi.org/10.1007/s10973-020-10300-1
45. [46] Said Z, Ghodbane M, Sundar LS, Tiwari AK, Sheikholeslami M, Boumeddane B. Heat transfer, entropy generation, economic and environmental analyses of linear Fresnel reflector using novel rGO-Co3O4 hybrid nanofluids. Renewable Energy 2021; 165(Part 1): 420-37. https://doi.org/10.1016/j.renene.2020.11.054.
46. [47] Ghodbane M, Said Z, Hachicha AA, Boumeddane B. Performance assessment of linear Fresnel solar reflector using MWCNTs/DW nanofluids. Renewable Energy 2020; 151: 43-56. https://doi.org/10.1016/j.renene.2019.10.137.
47. [48] Mebarek‐Oudina F. Convective heat transfer of Titania nanofluids of different base fluids in cylindrical annulus with discrete heat source. Heat Transfer—Asian Research 2019; 48(1): 135-47. https://doi.org/10.1002/htj.21375.
48. [49] Said Z, Abdelkareem MA, Rezk H, Nassef AM. Fuzzy modeling and optimization for experimental thermophysical properties of water and ethylene glycol mixture for Al2O3 and TiO2 based nanofluids. Powder Technology 2019; 353: 345-358. https://doi.org/10.1016/j.powtec.2019.05.036.
49. [50] Said Z, Abdelkareem MA, Rezk H, Nassef AM, Atwany HZ. Stability, thermophysical and electrical properties of synthesized carbon nanofiber and reduced-graphene oxide-based nanofluids and their hybrid along with fuzzy modeling approach. Powder Technology 2020. https://doi.org/10.1016/j.powtec.2020.02.026.
50. [51] Said Z, Arora S, Bellos E. A review on performance and environmental effects of conventional and nanofluid-based thermal photovoltaics. Renewable and Sustainable Energy Reviews 2018; 94: 302-316. https://doi.org/10.1016/j.rser.2018.06.010.
51. [52] Said Z, Assad MEH, Hachicha AA, Bellos E, Abdelkareem MA, Alazaizeh DZ, Yousef BAA. Enhancing the performance of automotive radiators using nanofluids. Renewable and Sustainable Energy Reviews 2019; 112: 183-194. https://doi.org/10.1016/j.rser.2019.05.052.
52. [53] Raza J, Mebarek-Oudina F, Chamkha AJ. Magnetohydrodynamic flow of molybdenum disulfide nanofluid in a channel with shape effects. Multidiscipline Modeling in Materials and Structures 2019; 15(4): 737-57, https://doi.org/10.1108/MMMS-07-2018-0133.
53. [54] Bellos E, Tzivanidis C. Performance analysis and optimization of an absorption chiller driven by nanofluid based solar flat plate collector. Journal of Cleaner Production 2018; 174: 256-272. https://doi.org/10.1016/j.jclepro.2017.10.313.
54. [55] Bellos E, Tzivanidis C. Multi-criteria evaluation of a nanofluid-based linear Fresnel solar collector. Solar Energy 2018; 163: 200-214. https://doi.org/10.1016/j.solener.2018.02.007.
55. [56] Alkasassbeh M, Omar Z, Mebarek‐Oudina F, Raza J, Chamkha A. Heat transfer study of convective fin with temperature‐dependent internal heat generation by hybrid block method. Heat Transfer—Asian Research 2019; 48(4): 1225-44. https://doi.org/10.002/htj.21428.
56. [57] Ghodbane M, Boumeddane B. Engineering design and optical investigation of a concentrating collector: Case study of a parabolic trough concentrator J Fundam Appl Sci. 2018; 10(2): 148-71. http://dx.doi.org/10.4314/jfas.v10i2.11.
57. [58] Ghodbane M, Boumeddane B. A parabolic trough solar collector as a solar system for heating water: a study based on numerical simulation. International Journal of Energetica (IJECA) 2017; 2(2): 29-37. https://dx.doi.org/10.47238/ijeca.v2i2.32.
58. [59] Bellos E. Progress in the design and the applications of Linear Fresnel Reflectors – A critical review. Thermal Science and Engineering Progress 2019; 10: 112-137. https://doi.org/10.1016/j.tsep.2019.01.014.
59. [60] Tiwari AK, Kumar V, Said Z, Paliwal HK. A review on the application of hybrid nanofluids for parabolic trough collector: Recent progress and outlook. Journal of Cleaner Production 2021; 292: 126031. https://doi.org/10.1016/j.jclepro.2021.
60. [61] Ebrazeh S, Sheikholeslami M. Applications of nanomaterial for parabolic trough collector. Powder Technology 2020; 375: 472-492. https://doi.org/10.1016/j.powtec.2020.08.005.
61. [62] Bellos E, Tzivanidis C. Alternative designs of parabolic trough solar collectors. Progress in Energy and Combustion Science 2019; 71: 81-117. https://doi.org/10.1016/j.pecs.2018.11.001.
62. [63] Manikandan GK, Iniyan S, Goic R. Enhancing the optical and thermal efficiency of a parabolic trough collector – A review. Applied Energy 2019; 235: 1524-1540. https://doi.org/10.016/j.apenergy.2018.11.048.
63. [64] Azzouzi D, Bourorga HE, Belainine KA, Boumeddane B. Experimental study of a designed solar parabolic trough with large rim angle. Renewable Energy 2018; 125: 495-500, https://doi.org/10.1016/j.renene.2018.01.041.
64. [65] Moloodpoor M, Mortazavi A, Ozbalta N. Thermal analysis of parabolic trough collectors via a swarm intelligence optimizer. Solar Energy 2019; 181: 264-275. https://doi.org/10.1016/j.solener.2019.02.008.
65. [66] Bellos E, Tzivanidis C, Tsimpoukis D. Thermal enhancement of parabolic trough collector with internally finned absorbers. Solar Energy 2017; 157:514-531. https://doi.org/10.1016/j.solener.2017.08.067.
66. [67] Bellos E, Tzivanidis C. Parametric investigation of nanofluids utilization in parabolic trough collectors. Thermal Science and Engineering Progress 2017; 2: 71-79. https://doi.org/10.1016/j.tsep.2017.05.001.
67. [68] Bellos E, Daniil I, Tzivanidis C. Multiple cylindrical inserts for parabolic trough solar collector. Applied Thermal Engineering 2018; 143: 80-89. https://doi.org/10.1016/j.applthermaleng.2018.07.086.
68. [69] Bellos E, Tzivanidis C. Investigation of a star flow insert in a parabolic trough solar collector. Applied Energy 2018; 224: 86-102. https://doi.org/10.1016/j.apenergy.2018.04.099.
69. [70] Bellos E, Tzivanidis C, Tsimpoukis D. Optimum number of internal fins in parabolic trough collectors. Applied Thermal Engineering 2018; 137: 669-677. https://doi.org/10.1016/j.applthermaleng.2018.04.037.
70. [71] Guven HM. Determination of error tolerances for the optical design of parabolic troughs for developing countries. Solar energy 1986;36(6):535-50, http://dx.doi.org/10.1016/0038-092X(86)90018-6.
71. [72] Ghodbane M, Boumeddane B. Optical modeling and thermal behavior of a parabolic trough solar collector in the Algerian sahara. AMSE JOURNALS-AMSE IIETA, MMC_B 2017;86(2):406-26. https://doi.org/10.18280/mmc_b.860207
72. [73] Kalogirou SA. Solar Energy Engineering: Processes and Systems. 1st ed. Academic Press; 2009.
73. [74] Wang J, Wang J, Bi X, W X. Performance simulation comparison for parabolic trough solar collectors in China. International Journal of Photoenergy 2016; Article ID 9260943:1-16. http://dx.doi.org/0.1155/2016/9260943.
74. [75] Stuetzle TA. Automatic control of the 30 MWe SEGS VI parabolic trough plant University of Wisconsin-Madison 2002.
75. [76] Jeter SM, Jarrar DI, Moustafa SA. Geometrical effects on the performance of trough collectors. Solar Energy 1983; 30(2): 109-113, https://doi.org/10.1016/0038-092X(83)90201-3.
76. [77] Jeter SM. Calculation of the concentrated flux density distribution in parabolic trough collectors by a semifinite formulation. Solar Energy 1986; 37(5): 335-345, https://doi.org/10.1016/0038-092X(86)90130-1.
77. [78] Jeter SM. Analytical determination of the optical performance of practical parabolic trough collectors from design data. Solar Energy 1987; 39(1): 11-21, https://doi.org/10.1016/S0038-092X(87)80047-6.
78. [79] Pierucci G, Fontani D, Sansoni P, Lucia MD. Shape Optimization for Parabolic Troughs Working in NonIdeal Conditions. Energy Procedia 2014; 57: 2231– 2240, http://dx.doi.org/10.1016/j.egypro.2014.10.230.
79. [80] Ochieng RM, Onyango FN. Some Techniques in Configurational Geometry as Applied to Solar Collectors and Concentrators. Solar Collectors and Panels, Theory and Applications. Sciyo; 2010; 357-378.
80. [81] Duffie JA, Beckman WA. Solar Engineering of Thermal Processes. 4th ed. Wiley; 2013.