TUNGSTEN KARBÜR TAKVİYELİ BAKIR ESASLI KOMPOZİT TOZUNUN MEKANİK ALAŞIMLAMA YÖNTEMİYLE SENTEZİNE İŞLEM KONTROL KATKILARININ ETKİSİ

Abstract

Tungsten karbür (WC) parçacık-takviyeli bakır (Cu) esaslı kompozitler geleneksel malzemelere göre özellikle aşınma dayanımı, sertlik, yüksek sıcaklık dayanımı ve ark oluşumu ile gerçekleşen malzeme transferi üzerindeki olumlu etkileri sayesinde elektrik kontak malzemesi üretiminde kullanılmaktadır. WC, elektrik kontak malzemelerinin üretiminde sıklıkla takviye malzemesi olarak kullanılır. Cu/WC kompozit tozu; işlemkontrol katkısı cinsi ve miktarı, öğütme hızı, bilye-toz-ağırlık oranı ve öğütme süresi gibi birçok işlem parametresinin optimize edilmesi sayesinde mekanik alaşımlama (MA) yöntemi ile üretilebilir. Bu nedenle çalışmada işlem kontrol katkısının, Cu/WC kompozit toz sentezine etkisi araştırılmıştır. Bu amaçla Cu ve WC tozlarından oluşan karışıma katı işlem kontrol katkısı olarak stearik asit, polietilen glikol ve çinko stearat ayrı ayrı ilave edilerek oluşturulan üç farklı karışım bilyeli öğütücüde öğütülmüştür. Polietilen glikol kullanımında öğütme verimi en düşük seviyelerde iken çinko stearatın 16 saate kadar belirgin etkisi öne çıkmaktadır. Ortalama toz boyutu değerleri ve SEM görüntülerinin karşılaştırılmasından 25 saatlik öğütme sonucunda en uygun işlem kontrol katkısının stearik asit olduğu tespit edilmiştir.

Keywords

• Bakır esaslı elektrik kontak malzemeleri
• Çinko stearat
• İşlem kontrol katkısı
• Polietilen glikol
• Stearik asit
• Tungsten karbür

Effect of Process Control Agents on the Synthesis of Tungsten Carbide Reinforced Copper Based Composite Powder Using Mechanical Alloying Method

Abstract

Tungsten carbide (WC) particle-reinforced copper (Cu) based composites, due to their wear resistance, hardness, high-temperature strength and excellent resistance to material transfer through arcing as compared to conventional materials, are used to produce electrical contact materials. WC is frequently used as a reinforcing material in production of electrical contact materials. Cu/WC composite powder can be produced using mechanical alloying (MA) technique by carefully optimizing a number of process parameters such as type and amount of process control agent, milling speed, ball-to-powder weight ratio and milling time. Therefore, this study investigated the effect of process control agent on the synthesis of Cu/WC composite powder. For this aim, three different powder mixtures containing Cu powder, WC powder and separately added solid process control agents (stearic acid, polyethylene glycol and zinc stearate) were milled in a ball-mill. The usage of zinc stearate was found effective up to 16 hours of milling whereas polyethylene glycol decreased milling efficiency to minimal value as compared to the other process control agents. In comparing average particle sizes and SEM pictures after 25 hours of milling, stearic acid was found the most suitable choice.

Keywords

• Copper based electrical contact materials
• Zinc stearate
• Process control agent
• Polyethylene glycol
• Stearic acid
• Tungsten carbide

References

1. Bıyık, S. (2019a) Effect of cubic and hexagonal boron nitride additions on the synthesis of Ag-SnO2 electrical contact material, Journal of Nanoelectronics and Optoelectronics, 14(7), 1010-1015. doi:10.1166/jno.2019.2592
2. Bıyık, S. (2019b) Influence of type of process control agent on the synthesis of Ag8ZnO composite powder, Acta Physica Polonica A, 135(4), 778-781. doi:10.12693/aphyspola.135.778
3. Bıyık, S. (2019c) Cu25W kompozit tozunun bilyeli öğütme yöntemiyle üretimine farklı işlem kontrol katkılarının etkisinin incelenmesi, Gümüşhane Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 9(2), 222-228. doi:10.17714/gumusfenbil.426995
4. Bıyık, S. (2018a) Effect of reinforcement ratio on physical and mechanical properties of Cu-W composites synthesized by ball milling, Materials Focus, 7(4), 535-541. doi:10.1166/mat.2018.1513
5. Bıyık, S. (2018b) Effect of polyethylene glycol on the mechanical alloying behavior of Cu-W electrical contact material, Acta Physica Polonica A, 134(1), 208-212. doi:10.12693/aphyspola.134.208
6. Bıyık, S. (2017) Characterization of nanocrystalline Cu25Mo electrical contact material synthesized via ball milling, Acta Physica Polonica A, 132(3), 886-888. doi:10.12693/aphyspola.132.886
7. Bıyık, S. ve Aydın, M. (2017a) Fabrication and arc-erosion behavior of Ag8SnO2 electrical contact materials under inductive loads, Acta Physica Polonica A, 131(3), 339-342. doi:10.12693/aphyspola.131.339
8. Bıyık, S. ve Aydın, M. (2017b) Optimization of mechanical alloying parameters of Cu25W electrical contact material, Acta Physica Polonica A, 132(3), 909-912. doi:10.12693/aphyspola.132.909

9. Bıyık, S. ve Aydın, M. (2016) Investigation of the effect of different current loads on the arc-erosion performance of electrical contacts, Acta Physica Polonica A, 129(4), 656-660. doi:10.12693/aphyspola.129.656
10. Bıyık, S., Arslan, F. ve Aydın, M. (2015) Arc-erosion behavior of boric oxide-reinforced silver-based electrical contact materials produced by mechanical alloying, Journal of Electronic Materials, 44(1), 457-466. doi:10.1007/s11664-014-3399-4
11. Bıyık, S. ve Aydın, M. (2015) The effect of milling speed on particle size and morphology of Cu25W composite powder, Acta Physica Polonica A, 127(4), 1255-1260. doi:10.12693/aphyspola.127.1255
12. Canakci, A., Varol, T. ve Ozsahin, S. (2013) Analysis of the effect of a new process control agent technique on the mechanical milling process using a neural network model: measurement and modeling, Measurement, 46(6), 1818-1827. doi:10.1016/j.measurement.2013.02.005
13. Canakci, A., Ozsahin, S. ve Varol, T. (2012a) Modeling the influence of a process control agent on the properties of metal matrix composite powders using artificial neural networks, Powder Technology, 228, 26-35. doi:10.1016/j.powtec.2012.04.045
14. Canakci, A., Varol, T. ve Nazik, C. (2012b) Effects of amount of methanol on characteristics of mechanically alloyed Al–Al2O3 composite powders, Materials Technology, 27(4), 320–327. doi:10.1179/1753555712Y.0000000014
15. Guo, X.H., Duan, K.Y., Wang, X., Song, K.X., Zhang, X.F. ve Li, K. (2023) Thermal and arc erosion behavior of CuCr contact material based on large plastic deformation treatment, Journal of Materials Research and Technology, 23, 348-358. doi:10.1016/j.jmrt.2023.01.011
16. Guzmán, D., González, F., Muranda, D., Aguilar, C., Guzmán, A., Soliz, Á., Lozada, L., Iturriza, I. ve Castro, F. (2023) Fabrication and arc erosion behavior of Ag-SnO2-ZnO electrical contact materials, Materials, 16(10), 3618. doi:10.3390/ma16103618
17. Güler, O., Varol, T., Alver, Ü. ve Bıyık, S. (2021) The wear and arc erosion behavior of novel copper based functionally graded electrical contact materials fabricated by hot pressing assisted electroless plating, Advanced Powder Technology, 32, 2873-2890. doi:10.1016/j.apt.2021.05.053
18. Kaykilarli, C., Uzunsoy, D. ve Aygül Yeprem, H. (2024) Role of process control agent in the production of Al2O3-reinforced titanium matrix composites, Ceramics International, 50(9), 16452-16462. doi:10.1016/j.ceramint.2024.02.130
19. Kiryukhantsev-Korneev, P., Sytchenko, A., Moskovskikh, D., Kuskov, K., Volkova, L., Poliakov, M., Pogozhev, Y., Yudin, S., Yakushko, E. ve Nepapushev, A. (2023) Hard wear-resistant Ti-Si-C coatings for Cu-Cr electrical contacts, Materials, 16(3), 936. doi:10.3390/ma16030936
20. Kumar, S.P., Parameshwaran, R., Kumar, S.A., Nathiya, S. ve Heenalisha, K. (2020) Electrical and mechanical studies on pure-silver coated aluminium based electrical contact materials, Materials Today-Proceedings, 33, 3621-3625. doi:10.1016/j.matpr.2020.05.666
21. Li, H.Y., Wang, X.H., Hu, Z.D. ve Qiu, Y.R. (2020a) Effect of Ni addition on the arc-erosion behavior of Ag-4 wt.%SnO2 electrical contact material, Journal of Alloys and Compounds, 829, 154487. doi:10.1016/j.jallcom.2020.154487
22. Li, H.Y., Wang, X.H., Hu, Z.D. ve Guo, X.H. (2020b) Investigation on arc behavior of AgNi electrical contact material with three-dimensional network structure, Vacuum, 175, 109290. doi:10.1016/j.vacuum.2020.109290
23. Li, H.Y., Wang, X. H., Liang, Y., Hu, Z.D. ve Guo, X.H. (2020c) Fabrication and characterization of Ag-4wt.%TiB2-4wt.%Ni contact materials utilizing coarse and ultrafine Ag powders, Vacuum, 182, 109756. doi:10.1016/j.vacuum.2020.109756
24. Li, H.Y., Wang, X.H., Fei, Y., Zhang, H., Liu, J.T., Li, Z. ve Qiu, Y.R. (2021) Effect of electric load characteristics on the arc erosion behavior of Ag-8wt.%Ni electrical contact material prepared by spark plasma sintering, Sensors and Actuators A-Physical, 326, 112718. doi:10.1016/j.sna.2021.112718
25. Liang, S., Li, Y., Zhang, Y., Zhou, M., Liu, S., Li, X., Geng, Y., Tian, B., Jia, Y., Liu, Y., Volinsky, A.A. (2023) Mechanical and electrical properties of Cu30Cr0.2Zr composites enhanced by CeO2/GO, Journal of Alloys and Compounds, 934, 167759. doi:10.1016/j.jallcom.2022.167759
26. Liu, S., Lu, P., Guan, J., Zhang, F. ve Hong, J. (2023) A new TiBN conductive ceramic powder and its application in copper-based electrical contact materials, Ceramics International, 49(15), 26084-26094. doi:10.1016/j.ceramint.2023.05.163
27. Liu, Y., Wang, X., Li, H., Lu, J., Wang, Z. ve Zhou, C. (2021) Enhancing properties of AgTiB2 contact material by CuO semi-coated TiB2 composite particles, Materials Letters, 293, 129703. doi:10.1016/j.matlet.2021.129703
28. Lungu, M.V. ve Barbu, A. (2022) Graphene and its derivative reinforced tungsten-copper composites for electrical contact applications: A review, Journal of Reinforced Plastics and Composites, 41(15-16), 624-636. doi:10.1177/07316844211063869
29. Ma, M., Wang, Z., Yuan, Z., Wang, J., Du, D., Chang, Y., Ma, J. ve Ou, D. (2023) Revealing the crucial role of skeleton restructuring on erosion dispersion of Ag–CuO contact materials, Applied Surface Science, 611, 155676. doi:10.1016/j.apsusc.2022.155676
30. Ma, B., Ding, H., Jiang, F., Hishinuma, Y., Luo, L., Zhang, Y., Wang, J., Sheng, X., Noto, H., Liu, J., Shi, J., Muroga, T. ve Wu, Y. (2024) Effect of process control agent on the synthesis of Cu-Y2O3 by mechanical alloying, Nuclear Materials and Energy, 38, 101599. doi:10.1016/j.nme.2024.101599
31. Mohandoss, T. ve Robert, F. (2023) Investigation of relay electrical contact failure using SEM and surface composition extraction with EDS and XRD, Iranian Journal of Science and Technology-Transactions of Electrical Engineering, 47(3), 803-812. doi:10.1007/s40998-022-00586-2
32. Mu, C.F., Shen, T., Yang, H., Chen, X., Qi, G.X. ve Wu, X.H. (2022) Investigation of the microstructure and electrical performance of Ag/SnO2In2O3 contacts with nickel addition fabricated by internal oxidation, Journal of Electronic Materials, 51(9), 4918-4937. doi:10.1007/s11664-022-09717-1
33. Pang, Y., Miao, X., Zhang, Q., Chen, Z., Hao, L., Zhong, J. ve Liang, S. (2023) Effect of graphene on the high-energy arc erosion performance of the W-Cu composite, Vacuum, 210, 111827. doi:10.1016/j.vacuum.2023.111827
34. Suryanarayana, C. (2004) Mechanical Alloying and Milling, CRC Press, Boca Raton, FL.
35. Tunc, S.A., Canakci, A., Karabacak, A.H., Celebi, M. ve Turkmen, M. (2024) Effect of different PCA types on morphology, physical, thermal and mechanical properties of AA2024-B4C composites, Powder Technology, 434, 119373. doi: 10.1016/j.powtec.2024.119373
36. Wang, H.T., Zheng, S.Q. ve Zhang, M. (2022) Study on the improvement of the performance of AgSnO2 contact material for low-voltage electrical apparatus with additive particle size, IEEJ Transactions on Electrical and Electronic Engineering, 17(10), 1388-1395. doi:10.1002/tee.23649
37. Wang, H., Wang, Y., Wang, J., Cai, Q. ve Hu, D. (2023) Enhancement of arc erosion resistance in AgCuO electrical contact materials through rare earth element doping: first-principles and experimental studies, International Journal of Molecular Sciences, 24(16), 12627. doi:10.3390/ijms241612627
38. Zhang, J., Mu, C., Shen, T. ve Qi, G. (2023) Study on the milling processes and sintering properties of Ag/SnO2 electrical contact material with different micro-structured SnO2 powders, Journal of Sol-Gel Science and Technology, 106, 444–454. doi:10.1007/s10971-022-05930-w