EV TİPİ BİR FIRININ DÜŞME TESTİNİN SONLU ELEMANLAR YÖNTEMİ İLE MODELLENMESİ

Abstract

Beyaz eşya sektöründe ürünler genellikle genleştirilmiş polistren malzeme kullanarak ambalajlanmaktadır. Ürün ambalajlanıp tüketiciye ulaşıncaya kadar her an düşme ve darbe etkisinde kalma riskine sahiptir. Olası bir düşme nedeniyle hasar görerek kullanılamaz hale gelecek ürün, satışa hazır bir mamulün satılamaz hale gelmesi anlamına geleceği için kaynak kaybına yol açacaktır. Yüksek sayıda üretim yapan işletmelerde küçük oranda bile bu hasarın görülmesi toplamda ciddi maliyetlere yol açmaktadır. Bu nedenle, ürün fabrikadan çıkmadan önce düşme testine tabi tutulmaktadır. Bu testte fabrikadan çıkmaya hazır bir ürünün kullanılması ve testtin sık sık gerçekleştirilmesi nedeniyle testin masrafı oldukça fazladır. Testin doğal bir kısıtı ise çarpma sırasında ürünün dinamiklerinin ve ürünü oluşturan parçaların hareketlerinin ambalaj malzemesi nedeniyle tam olarak gözlemlenememesidir. Sunulan çalışmada bir fırın sayısal olarak modellenmiş ve farklı düşme senaryoları için davranışı incelenmiştir. Sayısal model gerçekleştirilen deneysel düşme testi sonuçları ile doğrulanmıştır. Böylece tasarım aşamasında düşme sırasında hasara uğrayacak parçaların belirlenmesi ve buna uygun iyileştirmelerin yapılması mümkün olmuştur.

Keywords

• Düşme Testi,EPS,Sayısal Modelleme,Fırın

Modeling the Drop Test of Household Oven with Finite Element Method

Abstract

In order to prevent the damages that occur in the course of transportation, polystyrene (EPS) is commonly used in the domestic appliances sector. A product’s falling risk during transportation is not only available on the end user spot but also available at any moment after the packaging stage. It causes loss of resources because, ready to sale product became unsalable after damaged by possible fall. As a result, drop test is performed on products. Due to the fact that the samples of the test are required as ready for end use products and these tests are repeated very often, test expenses are very high. It is also not possible to observe movements of the pieces and product dynamics during the impact completely because of the packaging materials. An oven is modeled numerically and its behavior for various drop scenarios are examined in this study. Numerical model is verified with the experimental drop test results. Thus, it is possible to make improvements in the design by predicting probable damaged parts during impact.

Keywords

• Drop test,EPS,Numerical Analysis,Oven

References

1. Altair Engineering, (2011) Using computer aided engineering processes in packaging design development. Access adress: http://www.altairproductdesign.com/(S(osxrbhnssup320qhsvos4xmt))/images/en-US/CaseStudy/Mabe-Using-Computer-Aided-Engineering-Processes-in-Packaging-Design.pdf (Accessed in: 01.02.2014)
2. Altair Engineering, (2014) Practical aspects of finite element simulation, http://www.altairuniversity.com/free-ebooks-2/ (Accessed in: 01.06.2014)
3. ASTM D 5276 – 98.,(1998) Standart test method for drop test of loaded containers by free fall, American Society For Testing And Materials, West Conshohocken, PA, ABD
4. ASTM D 880 – 92., (2002) Standart test method for ımpact testing for shipping containers and systems, American Society For Testing And Materials, West Conshohocken, PA, ABD BASF A.Ş., (2006) Packaging with styropor, Access adress: http://styropor.basf.us/files/pdf/Packaging_with_Styropor.pdf (Accessed in: 01.02.2014)
5. Croop, B. ve Lobo, H., (2009) Selecting material models for the simulation of foams in ls-dyna, 7th European LS-DYNA Conference, Salzburg, Avusturya
6. Gere J., Timoshenko P.,(1997) Mechanics of Material, PWS Pub Co, ABD
7. Görücüoglu, B.,(2005) Çamasır makinası düşme testi deney ve simulasyonu, Yüksek Lisans Tezi, İ.T.Ü. Fen Bilimleri Enstitüsü, İstanbul.
8. Johnson, G. ve Cook W.,(1983) A constitutive model and data for metals subjected to large strains, high strain rates, and temperatures, 7th International Symposium Ballistics, Hague, Netherlands, 1–7.

9. Kim, J.G., Park, Y.K.,(2004) Experimental verification of drop/impact simulation for a cellular phone, Experimental Mechanics, 44(4), 375–380
10. Liu, S., Wang , X., Ma, B., Gan, Z., Zhang, H.,(2005) Drop test and simulation of portable electronic devices, 6th International Conference on Electronic Packaging Technology Shenzhen,1-4,
11. Liu W., Li H., (2011) Impact analysis of a cellular phone, 4th ANSA & META International Conference, Thessaloniki Greece, 1-3.
12. Matienssen W., Warlimont H., (2005) Handbook of Condensed Matter and Materials Data, sf. 501,502, 571, Springer, ABD
13. Mulkoğlu, O., Guler, M.A., Demirbağ, H., (2015) Drop test simulation and verification of a dishwasher mechanical structure, 10th European LS-DYNA Conference, Würzburg, Almanya
14. Neumayer, D., Chatiri, M. ve Höermann M., (2006) Drop test simulation of a cooker including foam packaging and pre-stressed plastic foil wrapping, 9th International LS-DYNA Conference, Simulation Technology (4), 18-33
15. Posch, W. ve Sageder, A., (2002) Borealis polypropylene-helping to shape the future of the White goods industry, Access adress: http://www.mscsoftware.co.kr/upfile/pro_pdf/1216_borealis_white_goods.pdf (Accessed in: 01.02.2014)
16. Tempelman, E., Dwaikat, M.M.S., Spitás, C.,(2012) Experimental and analytical study of free-fall drop impact testing of portable products, Experimental Mechanics, 52, 1385–1395
17. Verlysen P., Peirs J., Slyeken J., Faes, K., ve Duchene, L., (2011) Effects of strain rate on the forming behaviour of sheet metals, Journal of Materials Processing Technology, 211 (8), 1457–1464. http://dx.doi.org/10.1016/j.jmatprotec.2011.03.018
18. Wang H.L., Chen S.C., Huang L.T., Wang Y.C., (2004) Simulation and verification of the drop test of 3c products, 8th International LS-DYNA Users Conference, Drop/Impact Simulations, Detroit, 7-18