EFFECTS OF FUEL PROPERTIES AND SPRAYING FLUID ON GASOLINE ENGINES

Yıl 2018, Cilt: 2 Sayı: 1, 1 - 12, 22.05.2019

Cemil Koyunoğlu Fikret Yüksel

Öz

In this study, the ignition delay
measurement determined numerically by using some practical equations. Outboard
ignition engines take the fuel-air
mixture into the cylinder and compress it. High compression ratio is an
important parameter that increases engine efficiency. The compression ratio is
kept away from the knock limit, which is also defined by self-ignition of the mixture. The ignition
system should be able to initiate combustion without igniting the mixture at
the appropriate moment and causing undesired mechanical and thermal stresses. The
temperature at the tip of the spark plug at the time of ignition is
proportional to the blur of the gauge voltage and usually ranges from 500-800 ^oC.
A well-working flue gas should have a
porcelain temperature of less than 500 ^oC and no more than 850 ^oC.
The temperature at the end of the isolator is crucial for the development of
ignition and combustion. Higher tip temperatures, premature ignition, and low temperatures cause spark plug contamination and
kicking. Accumulation of unburned or slightly burnt hydrocarbons in the
interior of the buoy is indicated as the responsibility of the contamination
and therefore the singlet. Hydrocarbon deposits reduce electrical insulation
too much over time, preventing the syringe from forming between spark plug
nails. In our work, evaluations were made on hydrocarbon deposits in terms of
insulator temperature and system self-cleaning temperature and so on.

Anahtar Kelimeler

Fuel properties, Gasoline engines, Spray injection, Knock, octane number

Kaynakça

• 1. Benim AC, Syed KJ. Chapter 5 - Flashback by Autoignition. Flashback Mechanisms in Lean Premixed Gas Turbine Combustion. Boston: Academic Press; 2015. p. 27-39.
• 2 Glassman I, Yetter RA. Chapter 7 - Ignition. Combustion (Fourth Edition). Burlington: Academic Press; 2008. p. 379-408.
• 3. Lifshitz A. CHAPTER 16.5 - Ignition Delay Times. Handbook of Shock Waves. Burlington: Academic Press; 2001. p. 211-VII.
• 4. Hidaka Y, Sato K, Henmi Y, Tanaka H, Inami K. Shock-tube and modeling study of methane pyrolysis and oxidation. Combustion and Flame. 1999;118(3):340-58.
• 5. Havranek T, Kokes O. Income elasticity of gasoline demand: A meta-analysis. Energy Economics. 2015;47:77-86.
• 6. Demirel B, Wiser WH, Oblad AG, Zmierczak W, Shabtai J. Production of high octane gasoline components by hydroprocessing of coal-derived aromatic hydrocarbons. Fuel. 1998;77(4):301-11.
• 7. Asinger F. CHAPTER 4 - THE MANUFACTURE OF HIGH-EFFICIENCY CARBURETTOR FUELS. Mono-Olefins: Pergamon; 1968. p. 303-413.
• 8. Guzzella L, Onder CH. Introduction to Modeling and Control of Internal Combustion Engine Systems: Springer; 2004.
• 9. Gao J, Wu Y, Shen T. Combustion Phase Control of SI Gasoline Engines Using Hypothesis Test. IFAC-PapersOnLine. 2015;48(15):153-8.
• 10. Heywood J. Internal Combustion Engine Fundamentals: McGraw-Hill Education; 1988.
• 11. Stone R. Introduction to internal combustion engines: Macmillan; 1985.
• 12. Wang Z, Liu H, Reitz RD. Knocking combustion in spark-ignition engines. Progress in Energy and Combustion Science. 2017;61:78-112.
• 13. Reif K. Gasoline Engine Management: Systems and Components: Springer Fachmedien Wiesbaden; 2014.
• 14. Stone R. Introduction to Internal Combustion Engines: Palgrave Macmillan; 2012.
• 15. Guzzella L, Onder C. Introduction to Modeling and Control of Internal Combustion Engine Systems: Springer Berlin Heidelberg; 2013.