Investigation of Optimum Insulation Thickness in The Wall With Air-Cavity and The Environmental Analysis

Year 2026, Volume: 15 Issue: 1 , 228 - 244 , 24.03.2026

Meral Özel , Serhat Şengür , Cihan Özel

https://doi.org/10.17798/bitlisfen.1795736

https://izlik.org/JA94ZW34BJ

Abstract

Making energy efficient designs in building walls can be a solution to reduce increasing building energy consumption and thus environmental pollution. By using insulation and energy efficient building materials, the heating and cooling loads of buildings and therefore fuel consumption and environmental pollution can be significantly reduced. Therefore, this paper goals to evaluate the thermal, economic and environmental effects of walls with air-cavities by considering different wall orientations. The study uses a numerical method called the implicit finite difference procedure to compute annual transmission loads for walls that have and haven't air-cavities during the summer and winter seasons in Elazığ province of Turkey. The conclusions show that the annual cooling and heating loads decline by about 31% for all wall orientations when a 2.5 cm air-cavity is positioned in the center of an uninsulated concrete wall. The study also shows that the effect of the air-cavity on heat transmission loads declines as insulation thickness rises. Additionally, walls incorporating air cavities were analyzed to determine their annual average time lag and decrement factor. To identify the optimal insulation thickness, a cost analysis was conducted using annual transmission loads calculated under dynamic thermal conditions. The findings indicate that the most effective insulation thicknesses for walls with air cavities are 12.4 cm for south-facing orientations, 13.2 cm for north-facing, and 13.4 cm for east- and west-facing orientations. When these optimal values are applied across all orientations, the annual heating energy, fuel consumption, and associated emissions are reduced by 87.3%, 87.9%, and 88.0%, respectively.

Keywords

Air-Cavity , Dynamic thermal conditions , Heating and Cooling transmission loads , Economical and environmental parameters

References

• Ö. A. Dombaycı, M. Gölcü, and Y. Pancar, “Optimization of insulation thickness for external walls using different energy-sources,” Appl. Energy, vol. 83, no. 9, pp. 921–928, 2006.
• A. Bolattürk, “Optimum insulation thicknesses for building walls with respect to cooling and heating degree-hours in the warmest zone of Turkey,” Build. Environ., vol. 43, no. 6, pp. 1055–1064, 2008.
• S. A. Al-Sanea, M. F. Zedan, and S. N. Al-Hussain, “Effect of masonry material and surface absorptivity on critical thermal mass in insulated building walls,” Appl. Energy, vol. 102, pp. 1063–1070, 2013.
• Y. Zhang, K. Du, J. He, L. Yang, Y. Li, and S. Li, “Impact factors analysis on the thermal performance of hollow block wall,” Energy Build., vol. 75, pp. 330–341, 2014.
• S. A. Al-Sanea and M. F. Zedan, “Effect of thermal bridges on transmission loads and thermal resistance of building walls under dynamic conditions,” Appl. Energy, vol. 98, pp. 584–593, 2012.
• S. A. Al-Sanea, M. F. Zedan, and S. N. Al-Hussain, “Effect of thermal mass on performance of insulated building walls and the concept of energy savings potential,” Appl. Energy, vol. 89, no. 1, pp. 430–442, 2012.
• H. Kurt, “The usage of air gap in the composite wall for energy saving and air pollution,” Environ. Prog. Sustain. Energy, vol. 30, no. 3, pp. 450–458, 2011.
• Z. L. Zhang and B. J. Wachenfeldt, “Numerical study on the heat storing capacity of concrete walls with air cavities,” Energy Build., vol. 41, no. 7, pp. 769–773, 2009.
• S. A. Al-Sanea, M. F. Zedan, S. A. Al-Ajlan, and A. S. Abdul Hadi, “Heat transfer characteristics and optimum insulation thickness for cavity walls,” J. Therm. Envel. Build. Sci., vol. 26, no. 3, pp. 285–307, 2003.
• S. A. Al-Sanea and M. F. Zedan, “Improving thermal performance of building walls by optimizing insulation layer distribution and thickness for same thermal mass,” Appl. Energy, vol. 88, no. 9, pp. 3113–3124, 2011, doi: 10.1016/j.apenergy.2011.02.036.
• N. Pargana, M. D. Pinheiro, J. D. Silvestre, and J. De Brito, “Comparative environmental life cycle assessment of thermal insulation materials of buildings,” Energy Build., vol. 82, pp. 466–481, 2014.
• S. A. Al-Sanea, M. F. Zedan, and S. A. Al-Ajlan, “Effect of electricity tariff on the optimum insulation-thickness in building walls as determined by a dynamic heat-transfer model,” Appl. Energy, vol. 82, no. 4, pp. 313–330, 2005, doi: 10.1016/j.apenergy.2004.10.014.
• M. Ozel, “Effect of wall orientation on the optimum insulation thickness by using a dynamic method,” Appl. Energy, vol. 88, no. 7, pp. 2429–2435, 2011, doi: 10.1016/j.apenergy.2011.01.049.
• M. Ozel, “Thermal performance and optimum insulation thickness of building walls with different structure materials,” Appl. Therm. Eng., vol. 31, no. 17–18, pp. 3854–3863, 2011.
• M. Ozel, “Cost analysis for optimum thicknesses and environmental impacts of different insulation materials,” Energy Build., vol. 49, pp. 552–559, 2012.
• M. Ozel, “Determination of optimum insulation thickness based on cooling transmission load for building walls in a hot climate,” Energy Convers. Manag., vol. 66, pp. 106–114, 2013.
• M. Ozel, “Thermal, economical and environmental analysis of insulated building walls in a cold climate,” Energy Convers. Manag., vol. 76, pp. 674–684, 2013.
• N. Daouas, “A study on optimum insulation thickness in walls and energy savings in Tunisian buildings based on analytical calculation of cooling and heating transmission loads,” Appl. Energy, vol. 88, no. 1, pp. 156–164, 2011.
• H. Ramin, P. Hanafizadeh, and M. A. Akhavan-Behabadi, “Determination of optimum insulation thickness in different wall orientations and locations in Iran,” Adv. Build. Energy Res., vol. 10, no. 2, pp. 149–171, 2016.
• M. Ibrahim, N. Ghaddar, and K. Ghali, “Optimal location and thickness of insulation layers for minimizing building energy consumption,” J. Build. Perform. Simul., vol. 5, no. 6, pp. 384–398, 2012.
• S. A. Al-Sanea and M. F. Zedan, “Optimum insulation thickness for building walls in a hot-dry climate,” Int. J. Ambient Energy, vol. 23, no. 3, pp. 115–126, 2002.
• A. Bolattürk, “Determination of optimum insulation thickness for building walls with respect to various fuels and climate zones in Turkey,” Appl. Therm. Eng., vol. 26, no. 11–12, pp. 1301–1309, 2006.
• M. Erturk, “A new approach to calculate the energy savıng per unıt area and emıssıon per person ın exterıor wall of buıldıng usıng dıffrent ınsulatıon materıals and aır gap,” J. Fac. Eng. Archit. Gazi Univ., vol. 31, no. 2, pp. 395–406, 2016.
• M. Erturk, “A new model for exergetic optimum insulation thickness,” Int. J. Exergy, vol. 22, no. 4, pp. 309–330, 2017.
• M. Ertürk and A. Keçebaş, “Prediction of the effect of insulation thickness and emission on heating energy requirements of cities in the future,” Sustain. Cities Soc., vol. 75, p. 103270, 2021.
• A. Hasan, “Optimizing insulation thickness for buildings using life cycle cost,” Appl. Energy, vol. 63, no. 2, pp. 115–124, 1999.
• J. Barrau, M. Ibanez, and F. Badia, “Impact of the insulation materials’ features on the determination of optimum insulation thickness,” Int. J. Energy Environ. Eng., vol. 5, no. 2, p. 79, 2014.
• A. Shanmuga Sundaram and A. Bhaskaran, “Optimum insulation thickness of walls for energy-saving in hot regions of India,” Int. J. Sustain. Energy, vol. 33, no. 1, pp. 213–226, 2014.
• G. Özel, E. Açıkkalp, B. Görgün, H. Yamık, and N. Caner, “Optimum insulation thickness determination using the environmental and life cycle cost analyses based entransy approach,” Sustain. Energy Technol. Assessments, vol. 11, pp. 87–91, 2015.
• K. Çomaklı and B. Yüksel, “Optimum insulation thickness of external walls for energy saving,” Appl. Therm. Eng., vol. 23, no. 4, pp. 473–479, 2003.
• Ö. A. Dombaycı, “The environmental impact of optimum insulation thickness for external walls of buildings,” Build. Environ., vol. 42, no. 11, pp. 3855–3859, 2007.
• Ö. A. Dombayci, Ö. Atalay, Ş. G. Acar, E. Y. Ulu, and H. K. Ozturk, “Thermoeconomic method for determination of optimum insulation thickness of external walls for the houses: Case study for Turkey,” Sustain. Energy Technol. Assessments, vol. 22, pp. 1–8, 2017.
• N. Sisman, E. Kahya, N. Aras, and H. Aras, “Determination of optimum insulation thicknesses of the external walls and roof (ceiling) for Turkey’s different degree-day regions,” Energy Policy, vol. 35, no. 10, pp. 5151–5155, 2007.
• H. T. Ozkahraman and A. Bolatturk, “The use of tuff stone cladding in buildings for energy conservation,” Constr. Build. Mater., vol. 20, no. 7, pp. 435–440, 2006.
• O. Kaynakli, “A study on residential heating energy requirement and optimum insulation thickness,” Renew. Energy, vol. 33, no. 6, pp. 1164–1172, 2008.
• O. Kaynaklı, C. Yüce, O. Dogan, and Z. Kaynaklı, “A Study on Determınatıon of Optımum Thermal Insulatıon Thıckness usıng Life Cycle Cost Analysis,” Int. J. Adv. Mech. Civ. Eng., vol. 2, no. 6, pp. 1–5, 2015.
• A. Yildiz, G. Gurlek, M. Erkek, and N. Ozbalta, “Economical and environmental analyses of thermal insulation thickness in buildings,” J. Therm. Sci. Technol., vol. 28, no. 2, pp. 25–34, 2008.
• J. Yu, C. Yang, L. Tian, and D. Liao, “A study on optimum insulation thicknesses of external walls in hot summer and cold winter zone of China,” Appl. Energy, vol. 86, no. 11, pp. 2520–2529, 2009.
• M. Shahid, M. N. Karimi, and A. K. Mishra, “Optimum insulation thickness for external building walls for different climate zone in India,” J. Therm. Eng., vol. 10, no. 5, pp. 1198–1211, 2024.
• L. Malka, A. Kuriqi, and A. Haxhimusa, “Optimum insulation thickness design of exterior walls and overhauling cost to enhance the energy efficiency of Albanian’s buildings stock,” J. Clean. Prod., vol. 381, p. 135160, 2022.
• C. Aktemur, M. T. Çakır, and M. F. Çakır, “Optimising of thermal insulation thickness based on wall orientations and solar radiation using heating-degree hour method,” Case Stud. Therm. Eng., vol. 60, p. 104725, 2024.
• M. K. Özturan and A. K. Seyhan, “Determination of optimum insulation thickness of building walls according to four main directions by accounting for solar radiation: A case study of Erzincan, Türkiye,” Energy Build., vol. 304, p. 113871, 2024.
• M. K. Akyüz, “Enviroeconomic optimization of insulation thickness for building exterior walls through thermoeconomic and life cycle assessment analysis,” Case Stud. Therm. Eng., vol. 65, p. 105606, 2025.
• J. L. Threlkeld, “Thermal environment engineering,” 1998, Prentice-Hall, Englewood Cliffs, NJ.
• J. A. Duffie and W. A. Beckman, “Solar engineering of thermal processes John Wiley & Sons,” Inc. New York, 1991.
• M. Ozel and K. Pihtili, “Optimum location and distribution of insulation layers on building walls with various orientations,” Build. Environ., vol. 42, no. 8, pp. 3051–3059, 2007.
• State Meteorological Station, Records for weather data, Turkey, 2000-2014.
• Ö. Kaşka and R. Yumrutaş, “Comparison of experimental and theoretical results for the transient heat flow through multilayer walls and flat roofs,” Energy, vol. 33, no. 12, pp. 1816–1823, 2008.
• Natural Gas Equipment Manufacturers and Businessmen Association, web page, (http://www.dosider.org).
• Records of unit prices of insulation materials in Turkey, web page, (http://www.birimfiyat.com).
• Records of the Central Bank of Republic of Turkey, web page, (http://www.tcmb.gov.tr).