Research Article

Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment

Number: Advanced Online Publication Early Pub Date: November 18, 2026
TR EN

Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment

Abstract

AISI 1020 steel is widely used in engineering applications owing to its low cost and good formability; however, its relatively low surface hardness limits its wear resistance under severe contact conditions. This study investigated the mechanical and tribological response of AISI 1020 steel subjected to a hybrid treatment combining electrochemical boriding with subsequent thermal treatment and water quenching. Electrochemical boriding was performed at 950 °C under a current density of 200 mA cm-2 for 15 min. After the electrical current was interrupted, the specimens were cooled in the molten electrolyte to a furnace-indicated temperature of 725 °C, held for 30 min, and quenched in water. Cross-sectional microscopy revealed a predominantly light-contrast boride layer approximately 50 μm thick. X-ray diffraction identified Fe2B reflections without distinct detectable FeB reflections, supporting the formation of an Fe2B-dominant layer. The treated surface exhibited a hardness of 1744 ± 100 HV0.05. Ultimate tensile strength increased from 738 to 832 MPa, whereas total elongation decreased from 22.8% to 10.8%. Under the investigated impact-sliding conditions, wear volume per cycle decreased by approximately 11% in the impact-dominated region and 16% in the sliding-dominated region relative to untreated steel. Localized cracking was nevertheless observed in the treated surface after impact loading. These findings demonstrate that the combined treatment reduced wear under the tested conditions while introducing a trade-off between increased ultimate tensile strength and reduced tensile ductility.

Keywords

Supporting Institution

This work was supported by the Research Fund of Bilecik Şeyh Edebali University under Project No.: 2023-01.BŞEÜ.03-01. The authors also acknowledge the Eti Maden Operations General Directorate (Technology Development Department) for providing Na₂B₄O₇ raw materials used in the electrochemical boriding experiments.

Project Number

2023-01.BŞEÜ.03-01

Ethical Statement

This study does not involve any human participants, animal subjects, or clinical trials. Therefore, ethical approval from an institutional review board or ethics committee was not required. All experimental procedures were conducted in accordance with standard scientific research practices in materials science and engineering. The materials used in this study (AISI 1020 steel and industrial chemicals) were handled in compliance with relevant laboratory safety regulations and environmental guidelines. The authors confirm that the work presented in this manuscript is original, has not been published previously, and is not under consideration for publication elsewhere. All data generated or analyzed during this study are included in the manuscript, and no fabrication, falsification, or inappropriate data manipulation has been performed. The authors also declare that all sources have been properly cited and that there is no plagiarism in the manuscript. Any contributions from third parties have been appropriately acknowledged.

Thanks

The authors would like to express their sincere gratitude to the Research Fund of Bilecik Şeyh Edebali University for financial support under Project No.: 2023-01.BŞEÜ.03-01. The authors also gratefully acknowledge the Eti Maden Operations General Directorate (Technology Development Department) for supplying the Na₂B₄O₇ raw material used in the electrochemical boriding experiments. In addition, the authors would like to thank all technical staff involved in the experimental setup and testing processes for their valuable contributions.

References

  1. Van Long, L., Van Hien, D., Thanh, N. T., Tho, N. C., and Do, V. T., “Impact of cold-rolling and heat treatment on mechanical properties of dual-phase treated low carbon steel”, Advances in Materials Science and Engineering, 1-9. (2020). DOI: https://doi.org/10.1155/2020/1674837
  2. Hafeez, M. A., Usman, M., Arshad, M. A., and Adeel Umer, M., “Nanoindentation-based micro-mechanical and electrochemical properties of quench-hardened, tempered low-carbon steel”, Crystals, 10 (6): 508, (2020). DOI: https://doi.org/10.3390/cryst10060508
  3. Ulu, S., Kayali, Y., and Gunes, I., “Surface borided SAE 1020 steel with dual phase core microstructure”, Materials Science and Technology, 29 (3): 255-260, (2013). DOI: https://doi.org/10.1179/1743284712Y.0000000126
  4. Galiotto, A., Rosso, A. R., Almeida, E. A. D. S. D., Krelling, A. P., Milan, J. C. G., and Costa, C. E. D., “Characterization of different surface layers produced by solid boron-nitro-carburizing thermochemical treatment on AISI 1020”, Materials Research, 22 (5): 1-10, (2019). DOI: https://doi.org/10.1590/1980-5373-MR-2019-0316
  5. Krelling, A. P., Da Costa, C. E., Milan, J. C. G., and Almeida, E. A. S., “Micro-abrasive wear mechanisms of borided AISI 1020 steel”, Tribology International, 111: 234-242, (2017). DOI: https://doi.org/10.1016/j.triboint.2017.03.017
  6. Kartal, G., Timur, S., Eryilmaz, O. L., and Erdemir, A., “Influence of process duration on structure and chemistry of borided low carbon steel”, Surface and Coatings Technology, 205 (5): 1578-1583, (2010). DOI: https://doi.org/10.1016/j.surfcoat.2010.08.050
  7. Türkmen, I., and Yalamaç, E., “Growth of the Fe2B layer on SAE 1020 steel employed a boron source of H3BO3 during the powder-pack boriding method”, Journal of Alloys and Compounds, 744: 658-666, (2018). DOI: https://doi.org/10.1016/j.jallcom.2018.02.118
  8. Türkmen, I., Yalamaç, E., and Keddam, M., “Investigation of tribological behaviour and diffusion model of Fe2B layer formed by pack-boriding on SAE 1020 steel”, Surface and Coatings Technology, 377: 1-12, (2019). DOI: https://doi.org/10.1016/j.surfcoat.2019.08.017

Details

Primary Language

English

Subjects

Tribology

Journal Section

Research Article

Early Pub Date

November 18, 2026

Publication Date

-

Submission Date

March 27, 2026

Acceptance Date

October 1, 2026

Published in Issue

Year 2026 Number: Advanced Online Publication

APA
Mindivan, H., & Tuzcu Şahin, E. (2026). Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment. Gazi University Journal of Science, Advanced Online Publication. https://doi.org/10.35378/gujs.1917714
AMA
1.Mindivan H, Tuzcu Şahin E. Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment. Gazi University Journal of Science. 2026;(Advanced Online Publication). doi:10.35378/gujs.1917714
Chicago
Mindivan, Harun, and Eda Tuzcu Şahin. 2026. “Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel After Electrochemical Boriding and Subsequent Heat Treatment”. Gazi University Journal of Science, no. Advanced Online Publication. https://doi.org/10.35378/gujs.1917714.
EndNote
Mindivan H, Tuzcu Şahin E (November 18, 2026) Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment. Gazi University Journal of Science Advanced Online Publication
IEEE
[1]H. Mindivan and E. Tuzcu Şahin, “Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment”, Gazi University Journal of Science, no. Advanced Online Publication, Nov. 2026, doi: 10.35378/gujs.1917714.
ISNAD
Mindivan, Harun - Tuzcu Şahin, Eda. “Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel After Electrochemical Boriding and Subsequent Heat Treatment”. Gazi University Journal of Science. Advanced Online Publication (November 18, 2026). https://doi.org/10.35378/gujs.1917714.
JAMA
1.Mindivan H, Tuzcu Şahin E. Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment. Gazi University Journal of Science. 2026. doi:10.35378/gujs.1917714.
MLA
Mindivan, Harun, and Eda Tuzcu Şahin. “Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel After Electrochemical Boriding and Subsequent Heat Treatment”. Gazi University Journal of Science, no. Advanced Online Publication, Nov. 2026, doi:10.35378/gujs.1917714.
Vancouver
1.Harun Mindivan, Eda Tuzcu Şahin. Mechanical Properties and Impact-Sliding Wear of AISI 1020 Steel after Electrochemical Boriding and Subsequent Heat Treatment. Gazi University Journal of Science. 2026 Nov. 18;(Advanced Online Publication). doi:10.35378/gujs.1917714