Experimental Investigation of the Effect of the Cross-Sectional Geometry on the Flow

Yıl 2007, Cilt: 20 Sayı: 1, 7 - 14, 24.03.2010

Hasan Gül Duygu Evin

Öz

In this study, flow and friction characteristics in the rectangular-to-rectangular transition channels, which have cone angles of ф=4⁰, 5⁰, 6⁰ were investigated experimentally. The ratio of the channel inlet cross-sectional area to that of exit is 1:2. The transition ducts have different geometrical dimensions and cone angles. The duct entry and exit aspect ratios were chosen as 1.42 and 1.4, respectively. Measurements were taken at several stations, x/L, with the Reynolds number ranging from 2x10⁵ to 5x10⁵. Velocity profiles were measured starting from inlet to downstream using hot-wire anemometer. Based on experimental results, different flow characteristics were obtained. Friction coefficient decreased with increasing pipe length and increasing Reynolds number. It was seen that cross flows occurred at low Reynolds numbers.

 

Keywords: Asymmetric transition duct, Secondary Flow, Flow measurement

Anahtar Kelimeler

Asymmetric transition duct, Secondary Flow, Flow measurement

Kaynakça

• M. Rokni, et al., “Numerical and experimental investigation of turbulent flow in a rectangular duct”. International Journal For Numerical Methods in Fluids, 28: 225-242, (1998).
• Colin F et al., “The utilization of recuperated and regenerated engine cycles for high-efficiency gas turbines in the 21st century”, Applied Thermal Engineering, 16: 635-653, (1996)
• Burley J. R. and Carlson, J. R., “Circular –to Rectangular Transition duct for High-aspect ratio non-axisymmetric nozzles”, SAE, ASME, and ASEE, Joint Propulsion Conference 21st, Monterey, CA,:7, (1985).
• Burley J. R., Bangert, L. S., and Carlson, J. R., “Investigation of circular-to-rectangular transition ducts for high-aspect ratio nonaxisymmetric nozzles”, NASA TP 2534, Mar. (1986).
• Patrick, W. P. and McCormick, D. C., “Laser velocimeter and total pressure measurements in circular-to-rectangular transition ducts.” United Technologies Research Center Report 87-41, June, (1988).
• Patrick, W. P. and McCormick, D. C., “Circular-to- rectangular duct flows-A Benchmark experimental study”, Society of Automotive Engineers Tech. Rep, 78-1777, (1988).
• Miau, J. J., Lin, S. A., Chou, J. H., Wei, C. Y., and Lin , C. K., “An experimental study of flow in a Circular-Rectangular transition duct”, ASME, SEA and ASEE, Joint Propulsion Conference 24th, Boston, MA, 12, (1988)
• Miau, J. J., Leu, T. S., Chou, J. H., Lin, S. A., and Lin, C. K., “ Flow distortion in a circular-to- Rectangular transition duct”. AIAA, 28 (8): 1447- , (1990).
• Schlichting , H., 1979. Boundry Layer Theory.
• McGraw Hill Book Company, New York, 1979.
• Poiseuille, J and Hagen, G. 1840. “Recherches experimenteles tubes de tris petits diameters”,
• Comptes Rendus, 11: 961-967, 1041-1048, (1840)
• Dekam, E. and I., Calvert, J. R., “Geometry of transitional diffusers”, Journal of Wind Engineering and Industrial Aerodynamics, (1): 43-57, (1986)
• Dekam, E. I. and J. R. Calvert., “Area distribution along general transition geometries”, Journal of Wind Engineering and Industrial Aerodynamics, 18(3) 275-286, (1985)
• Dekam, E. I. and J. R. Calvert., “Design of transition sections between ducts of equal area”, Journal of Wind Engineering and Industrial Aerodynamics, 24(2): 117-127, (1986).