A PARAMETRIC STUDY FOR DRILLING HIGH QUALITY HOLES ON GLASS FIBER COMPOSITES

Yıl 2022, Cilt: 3 Sayı: 1, 26 - 32, 30.06.2022

Sinan Kesriklioğlu Cagatay Yilmaz

Öz

The objective of this study is to investigate the effect of cutting parameters on the quality of holes drilled in a glass fiber reinforced thermoset polymer with the delamination factor defined as the ratio of intended hole diameter to the diameter of the maximum area which contains both hole and delaminated area. For this purpose, Taguchi`s L9 orthogonal array was used to design the experiments and optimize the drilling parameters. 5 mm twist drill bits were used to drill the holes at various feeds and spindle speeds. The maximum diameters on the inlet and outlet sides of the holes drilled into the composite plates were then measured with an optical microscope to analyze the influence of the drilling parameters on the machining damage. The smallest delaminated area on the front and back sides of the composite plate was achieved with the lowest feed (0.05 mm/rev) for the drilling parameters used in this study. Even though the spindle speed was increased from 318 rpm to 2930 rpm at a constant feed of 0.05 mm/rev, it reduces the maximum diameter on the front and back sides by 9 𝜇m and 266 𝜇m, respectively. The obtained results showed that the material removal rates in the drilling of the glass fiber reinforced thermoset polymers can be increased significantly by setting the optimized process parameters without adversely affecting the hole quality.

Anahtar Kelimeler

Drilling, Composite, Hole Quality, Glass Fiber, Delamination

Destekleyen Kurum

The Scientific and Technological Research Council of Turkey (TUBİTAK)

Proje Numarası

221M085

Teşekkür

This work was supported by the Scientific and Technological Research Council of Turkey through the Scientific and Technological Research Projects Funding Program (TUBITAK 1001-221M085) and the Faculty of Engineering at Abdullah Gul University. The authors gratefully acknowledge the Central Research Facility at the Abdullah Gul University for the availability and use of the optical microscope.

Kaynakça

• Koklu, U., Morkavuk, S., Featherston, C., Haddad, M., Sanders, D., Aamir, M., … Giasin, K. (2021). The effect of cryogenic machining of S2 glass fibre composite on the hole form and dimensional tolerances. The International Journal of Advanced Manufacturing Technology, 115(1), 125–140. https://doi.org/10.1007/s00170-021-07150-y
• Khashaba, U. A. (2004). Delamination in drilling GFR-thermoset composites. Composite Structures, 63(3), 313–327. https://doi.org/https://doi.org/10.1016/S0263-8223(03)00180-6
• Singh, I., Bhatnagar, N., & Viswanath, P. (2008). Drilling of uni-directional glass fiber reinforced plastics: Experimental and finite element study. Materials and Design, 29(2), 546–553. https://doi.org/10.1016/j.matdes.2007.01.029
• Kilickap, E. (2010). Investigation into the effect of drilling parameters on delamination in drilling GFRP. Journal of Reinforced Plastics and Composites, 29(23), 3498–3503. https://doi.org/10.1177/0731684410386271
• Arul, S., Vijayaraghavan, L., Malhotra, S. K., & Krishnamurthy, R. (2006). Influence of tool material on dynamics of drilling of GFRP composites. The International Journal of Advanced Manufacturing Technology, 29(7), 655–662. https://doi.org/10.1007/s00170-005-2581-5
• Corrêa, H. L., Voichki Rodrigues, R., & da Costa, D. D. (2020). Machining process of glass-fiber-reinforced polyamide 6.6 Composite: pathways to improve the drilling of recycled polymers. Engineering Research Express, 2(1), 15037. https://doi.org/10.1088/2631-8695/ab7684
• El-Sonbaty, I., Khashaba, U. A., & Machaly, T. (2004). Factors affecting the machinability of GFR/epoxy composites. Composite Structures, 63(3–4), 329–338. https://doi.org/10.1016/S0263-8223(03)00181-8
• Giasin, K., Barouni, A., Dhakal, H. N., Featherson, C., Redouane, Z., Morkavuk, S., & Koklu, U. (2020). Microstructural investigation and hole quality evaluation in S2/FM94 glass-fibre composites under dry and cryogenic conditions. Journal of Reinforced Plastics and Composites. https://doi.org/10.1177/0731684420958479
• Khanna, N., Pusavec, F., Agrawal, C., & Krolczyk, G. M. (2020). Measurement and evaluation of hole attributes for drilling CFRP composites using an indigenously developed cryogenic machining facility. Measurement, 154, 107504. https://doi.org/https://doi.org/10.1016/j.measurement.2020.107504
• Khanna, N., Desai, K., Sheth, A., & Øllgaard Larsen, J. (2019). CFRP Machining on Indigenously Developing Cryogenic Machining Facility: An Initial Study. Materials Today: Proceedings, 18, 4598–4604. https://doi.org/https://doi.org/10.1016/j.matpr.2019.07.434
• Ramkumar, J., Aravindan, S., Malhotra, S. K., & Krishnamurthy, R. (2004). An enhancement of the machining performance of GFRP by oscillatory assisted drilling. International Journal of Advanced Manufacturing Technology, 23(3–4), 240–244. https://doi.org/10.1007/s00170-003-1660-8
• Singh, I., & Bhatnagar, N. (2006). Drilling-induced damage in uni-directional glass fiber reinforced plastic (UD-GFRP) composite laminates. International Journal of Advanced Manufacturing Technology, 27(9–10), 877–882. https://doi.org/10.1007/s00170-004-2282-5
• Khanna, N., Desai, K., & Sheth, A. (2018). Industry supported experimental studies on drilling of thick multi-directional GFRP composite material. Procedia CIRP, 77, 320–323. https://doi.org/https://doi.org/10.1016/j.procir.2018.09.025
• Minitab Inc. (2013). MINITAB statistical software. Version: Release 16.