EN
Using thermo-calc software to produce the phase diagram of Zn-Te system
Abstract
In this work, Thermo-Calc software 2019b is used to recalculate the liquidus-solidus phase diagram of the Zn-Te binary system. The produced phase diagram is in good agreement with the experimental results found in the literature, and it shows five stable phases, which are elemental Zn, elemental Te, ZnTe compound, Zn liquid, and Te liquid. A monotectic reaction is observed at monotectic temperature of 1479.14 K and 59.369 Zn mole percent, and a miscibility gap is found between 59.369 and 97.2781 Zn mole percent above the monotectic temperature. Moreover, there are two eutectic reactions at the Te and Zn terminals. From this phase diagram, the maximum solubility of ZnTe in liquid Zn is determined as 2.7219% at 1479.14 K. The melting points of Te, Zn, and stoichiometic ZnTe are found to be 722.587 ± 0.025 K, 692.680 ± 0.025 K, and 1568.400 ± 0.025 K respectively. These results are important for the development of preparation methods of ZnTe, which is important for several industries including solar cells.
Keywords
References
- [1] Sharma, R.C., Thermodynamic analysis and phase equilibria calculations for the Zn-Te, Zn-Se and Zn-S systems, J. Cryst. Growth, 1988, 88(2), 193-204.
- [2] Feutelais, Y., Haloui, A., Legendre, B., A thermodynamic evaluation of the Te-Zn system, Journal of Phase Equilibria, 1997, 18(1), 48-61.
- [3] Steininger, J., Strauss, A.J., Brebrick, R.F., Phase diagram of the Zn-Cd-Te ternary system, J. Electrochem. Soc.: Solid State Science, 1970, 117(10), 1305-1309.
- [4] Suthar, D., Himanshu, Patel, S.L., Chander, S., Kannan, M.D., Dhaka, M.S., Enhanced physicochemical properties of ZnTe thin films as potential buffer layer in solar cell applications, Solid State Sciences (2020), doi: https://doi.org/10.1016/j.solidstatesciences.2020.106346.
- [5] Haynes, W.M. (ed), CRC handbook of chemistry and physics (2nd ed.). Boca Raton, FL, USA: CRC Press, 2011, 12-80.
- [6] Li, J., Diercks, D.R., Ohno, T.R., Warren, C.W., Lonergan, M.C., Beach, J.D., Wolden. C.A., Controlled activation of ZnTe:Cu contacted CdTe solar cells using rapid thermal processing, Sol. Energy Mater. Sol. Cells., 2015, 133, 208-215.
- [7] Gessert, T.A., Asher, S., Johnston, S., Young, M., Dippo, P., Corwine, C., Analysis of CdS/CdTe devices incorporating a ZnTe:Cu/Ti Contact, Thin Solid Films, 2007, 515, 6103-6106.
- [8] Hussain, T., Al-Kuhali, M.F., Durrani, S.M.A., Qayyum, H.A., Influence of angle deposition on the properties of ZnTe thin films prepared by thermal evaporation, Ceram. Int., 2018, 44(9), 10130-10140.
Details
Primary Language
English
Subjects
Material Production Technologies
Journal Section
Research Article
Authors
Publication Date
September 30, 2020
Submission Date
May 16, 2020
Acceptance Date
August 30, 2020
Published in Issue
Year 2020 Volume: 4 Number: 3
APA
Ikhmayies, S. (2020). Using thermo-calc software to produce the phase diagram of Zn-Te system. Journal of Energy Systems, 4(3), 88-95. https://doi.org/10.30521/jes.738363
AMA
1.Ikhmayies S. Using thermo-calc software to produce the phase diagram of Zn-Te system. Journal of Energy Systems. 2020;4(3):88-95. doi:10.30521/jes.738363
Chicago
Ikhmayies, Shadia. 2020. “Using Thermo-Calc Software to Produce the Phase Diagram of Zn-Te System”. Journal of Energy Systems 4 (3): 88-95. https://doi.org/10.30521/jes.738363.
EndNote
Ikhmayies S (September 1, 2020) Using thermo-calc software to produce the phase diagram of Zn-Te system. Journal of Energy Systems 4 3 88–95.
IEEE
[1]S. Ikhmayies, “Using thermo-calc software to produce the phase diagram of Zn-Te system”, Journal of Energy Systems, vol. 4, no. 3, pp. 88–95, Sept. 2020, doi: 10.30521/jes.738363.
ISNAD
Ikhmayies, Shadia. “Using Thermo-Calc Software to Produce the Phase Diagram of Zn-Te System”. Journal of Energy Systems 4/3 (September 1, 2020): 88-95. https://doi.org/10.30521/jes.738363.
JAMA
1.Ikhmayies S. Using thermo-calc software to produce the phase diagram of Zn-Te system. Journal of Energy Systems. 2020;4:88–95.
MLA
Ikhmayies, Shadia. “Using Thermo-Calc Software to Produce the Phase Diagram of Zn-Te System”. Journal of Energy Systems, vol. 4, no. 3, Sept. 2020, pp. 88-95, doi:10.30521/jes.738363.
Vancouver
1.Shadia Ikhmayies. Using thermo-calc software to produce the phase diagram of Zn-Te system. Journal of Energy Systems. 2020 Sep. 1;4(3):88-95. doi:10.30521/jes.738363
Cited By
Microstructure and Chemical Composition Analysis of Double Wire Arc Additive Manufactured Bimetallic Structure
Journal of Materials Engineering and Performance
https://doi.org/10.1007/s11665-021-05819-9