Optimization of the S-Rotor Savonius Wind Turbine

Year 2020, Volume: 24 Issue: 6, 1216 - 1222, 01.12.2020

Cemil Yiğit

https://doi.org/10.16984/saufenbilder.780890

Cited By: 2

https://izlik.org/JA27FD28EJ

Abstract

In this study, 2D Computational Fluid Dynamics (CFD) model was used to investigate the optimum working conditions of the S-Rotor Savonius (S-RS) wind turbine and to determine the most suitable geometry. The CFD model has been validated by studies on the S-RS wind turbine in the literature. The sliding mesh method which uses a mesh motion was utilized to perform the numerical study. CFD analysis was carried out under various tip-speed ratio at 4 m/s airspeed for the S-RS wind turbine which has a frontal swept area of approximately 0.3 m2. Within the scope of the optimization study, aspect-ratio (AR) and overlap ratio (OR) of the S-RS wind turbine's rotor in the fixed frontal swept area were taken as parameters. The geometry of the S-rotor has been optimized using the Ansys/Response Surface Optimization (RSO) tool. Under the constraints in which the optimization study was carried out, aerodynamic efficiency was obtained as %22.19 at 0.848 AR and 0.068 OR. This yield is significant when the efficiency of S-RS’s wind turbine is taken into consideration.

Keywords

aspect ratio , overlap ratio , response surface optimization , power coefficient , vertical axis wind turbine

References

• S. Armstrong, A. Fiedler and S. Tullis, “Flow separation on a high Reynolds number, high solidity vertical axis wind turbine with straight and canted blades and canted blades with fences,” Renewable Energy, vol. 41, pp. 13-22, 2012.
• J. Chen, L. Chen, H. Xu, H. Yang, C. Ye and D. Liu, “Performance improvement of a vertical axis wind turbine by comprehensive assessment of an airfoil family,” Energy, vol. 114, pp. 318-331, 2016.
• W.H. Chen, C.Y. Chen, C.Y. Huang and C.J. Hwang, “Power output analysis and optimization of two straight-bladed vertical axis wind turbines,” Applied Energy, vol. 185, pp. 223-232, 2017.
• K.S. Jeon, J.I. Jeong, J.K. Pan and K.W. Ryu, “Effects of end plates with various shapes and sizes on helical Savonius wind turbines,” Renewable Energy, vol. 79, pp. 167-176, 2015.
• H. Jeong, S. Lee and S.D. Kwon, “Wind tunnel interference effects on power performance of small Darrieus wind turbines,” Advances in Civil, Environmental, and Materials Research (ACEM14), pp. 1-5, 2014.
• C. Kang, H. Liu and X. Yang, “Review of fluid dynamics aspects of Savonius-rotor-based vertical-axis wind rotors,” Renewable and Sustainable Energy Reviews, vol. 33, pp. 499-508, 2014.
• S.M.H. Karimian and A. Abdolahifar, “Performance investigation of a new Darrieus vertical axis wind turbine,” Energy, vol. 191, pp. 1-18, 2020.
• A.S. Saad, I.I. El-Sharkawy, S. Ookawara and M. Ahmed, “Performance enhancement of twisted-bladed Savonius vertical axis wind turbines,” Energy Conversion and Management, vol. 209, pp. 1-19, 2020.
• S. Sharma and R.K. Sharma, “Performance improvement of Savonius rotor using multiple quarter blades – a CFD investigation,” Energy Conversion and Management, vol. 127, pp. 43-54, 2016.
• S. Brusca, R. Lanzafame and M. Messina, “Design of a vertical-axis wind turbine: how the aspect ratio effects the turbine’s performance,” Int. J. Energy Environ. Eng., vol. 5, pp. 333-340, 2014.
• P. Jaohindy, S. McTavish, F. Garde and A. Bastide, “An analysis of the transient forces acting on Savonius rotors with different aspect ratios,” Renewable Energy, vol. 55, pp. 286-295, 2013.
• H.Y. Peng, H.F. Lam and H.J. Liu, “Power performance assessment of H-rotor vertical axis wind turbines with different aspect ratios in turbulent flows via experiments,” Energy, vol. 173, pp. 121-132, 2019.
• H.H. Al-Kayiem, B.A. Bhayo and M. Assadi, “Comparative critique on the design parameters and their effect on the performance of S-rotors,” Renewable Energy, vol. 99, pp. 1306-1317, 2016.
• S. Zanforlin and S. Deluca, “Effects of the Reynolds number and the tip losses on the optimal aspect ratio of straight-bladed vertical axis wind turbines,” Energy, vol. 148, pp. 179-195, 2018.
• Q. Li, T. Maeda, Y. Kamada, K. Shimizu, T. Ogasawara, A. Nakai and T. Kasuya, “Effect of rotor aspect ratio and solidity on a straight-bladed vertical axis wind turbine in three-dimensional analysis by the panel method,” Energy, vol. 121, pp. 1-9, 2017.
• I. Rabei and M. Gutu, “Analysis of the influence of the aspect ratio on the vertical axis wind rotor performance,” IOP Conf. Series: Materials Science and Engineering, vol. 564, pp. 1-6, 2019.
• M. Zemamou, M. Aggour and A. Toumi, “Review of savonius wind turbine design and performance,” Energy Procedia, vol. 141, pp. 383-388, 2017.
• N. Alom and U.K. Saha, “Arriving at the optimum overlap ratio for an elliptical-bladed Savonius,” in:Proceedings of ASME Turbo Expo 2017 Turbine Technical Conference and Exposition, pp. 1-10, 2017.
• W.A. El-Askary, A.S. Saad and A.M. AbdelSalam, “Experimental and theoretical studies for improving the performance of a modified shape Savonius wind turbine,” J. Energy Resour. Technol., vol. 142, no. 12, pp. 1-12, 2020.
• M.H. Nasef, W.A. El-Askary, A.A. AbdEl-Hamid and H.E. Gad, “Evaluation of Savonius rotor performance: Static and dynamic studies,” J. Wind Eng. Ind. Aerodyn., vol. 123, pp. 1-11, 2013.
• M.A. Kamoji, S.B. Kedare and S.V. Prabhu, “Experimental investigation on single stage modified Savonius rotor,” Applied Energy, vol. 86, pp. 1064-1073, 2009.
• R. Tania, R.L. Florin, I.D. Adriana, M. Roxana, A. Ancuta and D. Florin, “Experimental investigation on the influence of overlap ratio on Savonius turbines performance,” International Journal of Renewable Energy Research, vol. 8, no. 3, pp. 1791-1799, 2018.
• J. Yao, F. Li, J. Chen, Z. Yuan and W. Mai, “Parameter analysis of Savonius hydraulic turbine considering the effect of reducing flow velocity,” Energies, vol. 13, pp. 1-16, 2020.
• J.L. Menet and N. Bourabaa, “Increase in the Savonius rotors efficiency via a parametric investigation,” European Wind Energy Conference, pp. 1-11, 2004.
• A. Rezaeiha, I. Kalkman and B. Blocken, “CFD simulation of a vertical axis wind turbine operating at a moderate tip speed ratio: Guidelines for minimum domain size and azimuthal increment,” Renewable Energy, vol. 107, pp. 373-385, 2017.
• [R. Lanzafame, S. Mauro and M. Messina, “2D CFD modeling of h-Darrieus wind turbines using a transition turbulence model,” Energy Procedia, vol. 45, pp. 131-140, 2014.