Parameter Optimization of Frequency Selective Surfaces Made of Composite Materials

Yıl 2021, , 357 - 363, 15.04.2021

Abdullah Oğuz Kızılçay

https://doi.org/10.16984/saufenbilder.817605

Öz

Debye model is used for approximating the frequency dependent complex effective permittivity of the composite structures in filter and shielding applications at microwave frequencies. In debye model, desired shielding effectiveness (SE) is obtained by determining the Debye parameters using trial and error method. But this may result in wasting time or not converging to an optimum solution. In this work to overcome this problem Debye parameters were optimized by using Differential Evolution (DE) algorithm. A Maxwell Garnett (MG) mixing rule was applied to these optimized parameters to obtain frequency selective surface (FSS) parameters. 12dB shielding threshold was chosen between 0.05 – 5GHz frequency range. In accordance with the obtained parameters of FSS, a structure was designed in CST simulation software and simulations had been conducted to obtain SE results. It was seen that the results obtained from analytical computations agree with those obtained from simulations.

Anahtar Kelimeler

frequency selective surface, debye model, composite material, differential evolution algorithm

Kaynakça

• [1] B. Kanberoğlu, M. H. Nisanci, A. Ş. Demirkıran. "Electromagnetic characterization of ceramic material produced with natural zeolite", Materials Science in Semiconductor Processing, Vol.38, pp.352, 2015.
• [2] M. H. Nisanci, F. De Paulis, D. Di Febo, and A. Orlandi, “Synthesis of composite materials with conductive aligned cylindrical inclusions,” Prog. Electromagn. Res. Symp., no. May 2015, pp. 646–649, 2012.
• [3] R. D. Seager, A. Chauraya, J. Bowman, M. Broughton, and N. Nimkulrat, “Fabrication of fabric based Frequency Selective Surfaces (FSS),” 8th Eur. Conf. Antennas Propagation, EuCAP 2014, no. September 2017, pp. 1978–1980, 2014.
• [4] J. Wang, B. Zhou, L. Shi, C. Gao, and B. Chen, “Analyzing the electromagnetic performances of composite materials with the FDTD method,” IEEE Trans. Antennas Propag., vol. 61, no. 5, pp. 2646–2654, 2013.
• [5] Y. Mannaa and R. W. Aldhaheri, “New dual-band frequency selective surface for GSM shielding in secure-electromagnatic buildings using square loop fractal configurations,” Mediterr. Microw. Symp., pp. 1–4, 2017.
• [6] W. Kiermeier and E. Biebl, “New dual-band frequency selective surfaces for GSM frequency shielding,” Proc. 37th Eur. Microw. Conf. EUMC, no. October, pp. 222–225, 2007.
• [7] S. Kovar, J. Valouch, H. Urbancokova, M. Adamek, and V. Mach, “Simulation of Shielding Effectiveness of Materials Using CST Studio,” Wseas Trans. Commun., vol. 16, pp. 131–136, 2017.
• [8] E. Delihasanlar and A. H. Yuzer, “Wearable Textile Fabric Based 3D Metamaterials Absorber in X-Band,” vol. 35, no. 2, pp. 230–236, 2020.
• [9] R. Storn and K. Price, “Differential Evolution - A Simple and Efficient Heuristic for Global Optimization over Continuous Spaces,” J. Glob. Optim., vol. 11, pp. 341–359, 1997.
• [10] S. Ghosh and S. Lim, “Fluidically reconfigurable multifunctional frequency-selective surface with miniaturization Characteristic,” IEEE Trans. Microw. Theory Tech., vol. 66, no. 8, pp. 3857–3865, 2018.
• [11] M. H. Nisanci, F. De Paulis, D. Di Febo, and A. Orlandi, “Sensitivity analysis of electromagnetic transmission, reflection and absorption coefficients for biphasic composite structures,” IEEE Int. Symp. Electromagn. Compat., vol. 0, pp. 438–443, 2014.
• [12] D.D.L. Chung, “Materials for Electromagnetic Interference Shielding,” J. Mater. Eng. Perform., vol. 9, no. 3, pp. 350–354, 2000.
• [13] Y. Akinay and A. O. Kizilcay, “Computation and modeling of microwave absorbing CuO/graphene nanocomposites” Polym. Compos., vol. 41, no. 1, pp. 227–232, 2020.
• [14] S. Kashi, R. K. Gupta, T. Baum, N. Kao, and S. N. Bhattacharya, “Dielectric properties and electromagnetic interference shielding effectiveness of graphene-based biodegradable nanocomposites,” Mater. Des., vol. 109, no. February 2018, pp. 68–78, 2016.
• [15] E. Delihasanlar and A. H. Yuzer, “Simulation modelling and calculation of dielectric permittivity of Opuntia at 1.7–2.6 GHz,” J. Microw. Power Electromagn. Energy, vol. 51, no. 2, pp. 150–158, 2017.
• [16] F. De Paulis, M. H. Nisanci, A. Orlandi, M. Y. Koledintseva, and J. L. Drewniak, “Design of homogeneous and composite materials from shielding effectiveness specifications,” IEEE Trans. Electromagn. Compat., vol. 56, no. 2, pp. 343–351, 2014.
• [17] C. DÖĞÜŞGEN ERBAŞ and S. KENT, “Ekranlama Veri̇mli̇li̇ği Karakteri̇sti̇ği̇ Baz Alinarak Madde Sentezlenmesi İçi̇n Anali̇ti̇k Bi̇r Yaklaşim,” Uludağ Univ. J. Fac. Eng., vol. 22, no. 1, pp. 95–95, 2017.
• [18] N. N. Rao, Elements of Engineering Electromagnetics, Fifth Ed. Upper Saddle River, NJ: Prentice-Hall, Inc, 2000.
• [19] L. Jebaraj, C. Venkatesan, I. Soubache, and C. C. A. Rajan, “Application of differential evolution algorithm in static and dynamic economic or emission dispatch problem: A review,” Renew. Sustain. Energy Rev., vol. 77, no. March 2020, pp. 1206–1220, 2017.
• [20] H. Lei, L. Li, and C. H. Wu, “Evolutionary model selection and parameter estimation for protein-protein interaction network based on differential evolution algorithm,” IEEE/ACM Trans. Comput. Biol. Bioinforma., vol. 12, no. 3, pp. 622–631, 2015.
• [21] D. Karaboǧa and S. Ökdem, “A simple and global optimization algorithm for engineering problems: Differential evolution algorithm,” Turkish J. Electr. Eng. Comput. Sci., vol. 12, no. 1, pp. 53–60, 2004.
• [22] A. . De Paulis, Francesco; Nisanci, M. Hilmi; Koledintseva, M.Y.;Drewniak, J.L.; Orlandi, “Derivation of Homogeneous Permittivity of Cal Inclusions for Causal Electromagnetic,” vol. 37, no. July 2011, pp. 205–235, 2012.