Investigating the Wear Behaviour of Induction Hardened 100Cr6 Steel

Yıl 2018, Cilt: 22 Sayı: 5, 1174 - 1180, 01.10.2018

Gülcan Toktaş , Alaaddin Toktaş , Murat Can Duran

https://doi.org/10.16984/saufenbilder.304203

Cited By: 1

Öz

100Cr6
steel surface was induction hardened in order to be used in a bushing
manufacturing.  After examininig the
microstructure and hardness variations of the hardened surfaces, ball-on disc
type wear tests were carried out.  Wear
tests were performed at 4,92 mm/s sliding speed, under various loads (2,5-5-10
N), in dry medium and at room temperature. 
The results of wear tests were evaluated by the mass loss method.  The coefficients of friction were obtained
during wear tests.   The wear tracks and
surfaces were investigated by optic and scanning electron microscopes. 

As
a result, the surface hardness of the steel was obtained 2,5 times more than
the core hardness by the aid of formed martensitic matrix structure instead of
pearlitic one on steel surface by induction hardening process. It is seen that
the highest mass loss was obtained by applying 5 N load in wear tests.

Anahtar Kelimeler

100Cr6 Steel, Induction Hardening, Wear

Kaynakça

• [1] M. C. M. J. Schneider, "Introduction to surface hardening of steel," in ASM Handbook, Heat Treating, ASM International, vol. 4A, J. Dossett, Ed. 1991, pp. 259-267.
• [2] E.C. Santos, K. Kida, T. Honda, H. Koike a. J. Rozwadowska, "Fatigue strength improvement of AISI 52100 bearing steel by induction and repeated quenching," Mater. Sci., vol.47, no.5, pp. 677-682, Mar 2012.
• [3] J. Grum, Induction heat treating, Encyclopedia of tribology, Springer, pp.1796-1808, 2013.
• [4] P. V. Krishna,R. R. Srikant, M. Iqbal, N. Sriram, "Effect of austempering and martempering on the properties of AISI 52100 steel," ISRN Tribology, vol. 2013, Article ID 515484, 6 pages, 2013.
• [5] V. Rudnev, G.A. Fett A. Griebel, J. Tartaglia, Principles of induction hardening and inspection, ASM Handbook, vol.4c, ASM International.
• [6] J. Yi, M. Gharghouri, P. Bocher, M. Medraj, "Distorsion and residual stress measurements of induction hardened AISI discs," Mater. Chem. Phys.,vol. 142, no. 1, pp. 248-258, oct 2013.
• [7] G. V. B. Lemos, T. K.Hirsch, A. S. Rocha, R.M. Nunes, "Residual stressa analysis of drive shafts after induction hardening," Mater. Res., vol. 17, no.1, pp. 70-74, Apr 2014.
• [8] M. Sharma, J. S. Kohli, S. Akhai, "Metallurgical analysis of cracks encountered during induction hardening of crankshafts," Int. J. Res. Adv. Tech., vol.2,no. 4, pp. 295-304, Apr 2014.
• [9] A. Kusmoko, D. Dunne, R. Dahar, H. Li, "Surface treatment evaluation of induction hardened and tempered 1045 steel," Int. j. curr.eng. tech., pp. 1236-1239, june 2014.
• [10] K. Sipos, M. Lopez, M. Trucco, "Surface martensite white layer produced by adhesive sliding wear-friction in AISI 1065 steel," Revista Latinoamerica de Metalurgia Materiales, vol.28, no.1, pp. 46-50, june 2008.