Nonlinear Finite Element Analysis of Intervertebral Disc: A Comparative Study

Yıl 2018, Cilt: 22 Sayı: 5, 1282 - 1287, 01.10.2018

Suzan Cansel Doğru

https://doi.org/10.16984/saufenbilder.305347

Cited By: 1

Öz

The aims of the study were i) to develop a finite element model of a functional spinal unit
(FSU) without ligaments at cervical region, ii)
to simulate different material properties of intervertebral disc for analysing
degeneration and iii) to investigate
the influence of disc degeneration on the biomechanical behaviour of a motion. To
do so, two-dimensional computed tomography images of spine recorded from
volunteer was converted into three-dimensional vertebrae model with different material
properties section by section. Material properties of intervertebral disc are
described nonlinear in finite element analysis. Moment was applied on superior endplate
of vertebrae as 7.5 Nm. The boundary condition was described on the endplate of adjacent inferior vertebrae as fixed in
space. Stress distribution over the nucleus and motions of the
functional spinal unit were calculated using finite element analysis. The results
were compared with physiological motions of functional spinal unit from literature.
At the result, more realistic result of disc model was obtained by fluid filled
cavity model with regard to maximum stress value on disc and intradiscal
pressure. The fluid in the shell simulate incompressible feature like reality.

Anahtar Kelimeler

Finite element analysis, intervertebral disc, 3D model from CT

Kaynakça

• S. Gupta and P. Dan, Bone geometry and mechanical properties of the human scapula using computed tomography data, Trends Biomater Artif Organs, Vol. 17, pp 61-70, 2004.
• J. S. Pooni, D. W. L. Hukins, P. F. Harris and et. al., Comparison of the structure of human intervertebral discs in the cervical, throcal and lumbar areas of the spine, Surg Radiol Anat, Vol. 8, pp 175-182, 1986.
• M. M. Panjabi and A. A. White, Clinical Biomechanics of the Spine, Lippincott-Raven Publications, Philadelphia, New York, 1990.
• A. Nachemson and J. M. Morris, In vivo measurements of intradiscal pressure discometry, a method for the determination of pressure in the lower lumbar discs, J Bone Joint Surg AM, Vol. 46, pp 1077-1092, 1964.
• K. L. Markolf and J. M. Morris, The structural compenents of the ivd, J Bone Joint Surg AM, vol. 56, pp 4, 1974.
• S. C. Dogru, Finite element analysis of dynamic pedicle screw - rod assembly after lomber spine facetectomy application, (master thesis), Istanbul Technical University, 2013. A. B. Joshi, Mechanical behavior of the human lumbar intervertebral disc with polymeric hydrogel nucleus implant: an experimental and finite element study, (doctorate thesis), Drexel University, 2004.
• H. J. Wilke, P. Neef, M. Caimi and et.al., New in vivo measurements of pressures in the intervertebral disc in daily life, Spine, Vol. 24, pp 755-762, 1999.
• J. Miller, C. Schmatz, and A. Schultz, Lumbar disc degeneration: correlation with age, sex, and spine level in 600 autopsy specimens. Spine, vol. 13, pp 173–178, 1988.
• R. Gunzburg, R. Parkinson, R. Moore and et.al., A cadaveric study comparing discography, magnetic resonance imaging, histology, and mechanical behavior of the human lumbar disc. Spine, vol. 17, pp 417–426, 1992.
• A. Rohlmann, T. Zander, H. Schmidt and et.al., Analysis of the influence of disc degeneration on the mechanical behaviour of a lumbar motion segment using the finite element method, J Biomech, vol. 39, pp 2484—2490, 2006.
• A. Joshi, C. J. Massey, A. Karduna and et.al., The effect of nucleus implant parameters on the compressive mechanics of the lumbar intervertebral disc: a finite element study, J Biomed Mater Res B Appl Biomater, vol. 90, pp 596–607, 2009.
• S.C. Cowin, Wolff’s law of trabecular architecture at remodeling equilibrium, J Biomech Eng, vol. 108, pp 83-88, 1986.