Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi

Süleyman Kılıç; Mehmet Fatih Demirdöğen

doi:10.29137/umagd.987547

EN TR

Investigation of the Effect of Temperature and Strain Rate on Mechanical Properties

Abstract

The tensile test is one of the most basic and simple tests in which the material is pulled in a single axis until it breaks and allow us to recognize the material from the data obtained from it. While recognizing materials, their behavior under different temperatures and strain rates is also important. Especially in the manufacturing industry, there are many different production and shaping methods, and each has its own characteristics. For example, in the hot deep drawing process, the mechanical properties of the material can be determined by hot tensile tests. At the same time, this situation has become more important with the development of finite element analysis programs. Because modeling under the same conditions is very effective on the accuracy of the results. In this study, the effects of temperature and strain rate on tensile properties are investigated in steel, titanium, aluminum and nickel alloys. In the examinations, it is seen that the change of the temperature and strain rate for these materials have a great effect on the stress and ductility.

Keywords

Strain rate, Temperature, Steel, Titanium, Aluminum, Nickel alloys

Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi

Abstract

Çekme testi, malzemenin kopana dek tek eksende çekildiği ve buradan elde edilen verilerden malzemeyi tanımamızı sağlayan en temel ve basit testlerden biridir. Malzemeleri tanırken onların farklı sıcaklık ve deformasyon hızları altındaki davranışları da önem arz etmektedir. Özellikle imalat sanayinde çok farklı üretim ve şekillendirme yöntemleri mevcut olup her birinin kendine has özellikleri mevcuttur. Örneğin, sıcak derin çekme işleminde, sıcak yapılan çekme deneyleri ile malzemenin mekanik özellikleri belirlenebilmektedir. Aynı zamanda sonlu elemanlar analiz programlarının gelişmesiyle beraber bu durum daha önemli hale gelmiştir. Çünkü aynı koşullar altında modelleme yapılması sonuçların doğruluğu üzerinde oldukça etkilidir. Bu çalışma kapsamında çelik, titanyum, alüminyum ve nikel alaşımlarında sıcaklık ve deformasyon hızının çekme özelliklerine etkisi araştırılmıştır. Yapılan incelemelerde, bu malzemeler için sıcaklık ve deformasyon hızı değişiminin, gerilme ve süneklik üzerinde etkisinin çok fazla olduğu görülmüştür.

Keywords

Deformasyon hızı, Sıcaklık, Çelik, Titanyum, Alüminyum, Nikel alaşımları

References

Alsagabi, S., Alqahtani, M. & Alajlan, A., (2018). The Elevated Temperature Deformation of G115 Steel and the Associated Deformation Mechanism. International Journal of Advances in Materials Science and Engineering (IJAMSE), 7 (1): 1-7. https://doi.org/10.14810/ijamse.2018.7101
Altan, T. & Long, J., (2015). Forming Aluminum Alloys at Elevated Temperatures, Part 1, How Process Details Change for Warm and Hot Forming. Stamping Journal, 1 (1): 1-4.
Attar, H. R., Li, N. & Foster, A., (2021). A New Design Guideline Development Strategy for Aluminium Alloy Corners Formed through Cold and Hot Stamping Processes. Materials Design, 207 (1): 109856. https://doi.org/10.1016/j.matdes.2021.109856
Borek, W., Lis, M., Gołombek, K., Sakiewicz, P. & Piotrowski, K., (2019). Effect of Plastic Deformation Rate at Room Temperature on Structure and Mechanical Properties of High-Mn Austenitic Mn-Al-Si 25-3-3 Type Steel. Archives of Materials Science and Engineering, 96 (1): 22-31.
Dai, Q., Deng, Y., Jiang, H., Tang, J. & Chen, J., (2019). Hot Tensile Deformation Behaviors and a Phenomenological Aa5083 Aluminum Alloy Fracture Damage Model. Materials Science and Engineering: A, 766 (1): 138325. https://doi.org/10.1016/j.msea.2019.138325
Despax, L., Vidal, V., Delagnes, D., Dehmas, M., Matsumoto, H. & Velay, V., (2020). Influence of Strain Rate and Temperature on the Deformation Mechanisms of a Fine-Grained Ti-6al-4v Alloy. Materials Science and Engineering: A, 790 (1): 139718. https://doi.org/10.1016/j.msea.2020.139718
Gruber, B., Weißensteiner, I., Kremmer, T., Grabner, F., Falkinger, G., Schökel, A., Spieckermann, F., Schäublin, R., Uggowitzer, P. J. & Pogatscher, S., (2020). Mechanism of Low Temperature Deformation in Aluminium Alloys. Materials Science and Engineering: A, 795 (1): 139935. https://doi.org/10.1016/j.msea.2020.139935
Haitao, X., Dengke, W. & Kaihong, S., (2020). Effect of Deformation Temperature on Mechanical Properties and Microstructure of Twip Steel for Expansion Tube. High Temperature Materials and Processes, 39 (1): 63-73. doi:10.1515/htmp-2020-0020
Hao, F., Xiao, J., Feng, Y., Wang, Y., Ju, J., Du, Y., Wang, K., Xue, L. n., Nie, Z. & Tan, C., (2020). Tensile Deformation Behavior of a near-Α Titanium Alloy Ti-6al-2zr-1mo-1v under a Wide Temperature Range. Journal of Materials Research and Technology, 9 (3): 2818-2831. https://doi.org/10.1016/j.jmrt.2020.01.016
Jiang, Y.-Q., Lin, Y. C., Jiang, X.-Y., He, D.-G., Zhang, X.-Y. & Kotkunde, N., (2020). Hot Tensile Properties, Microstructure Evolution and Fracture Mechanisms of Ti-6al-4v Alloy with Initial Coarse Equiaxed Phases. Materials Characterization, 163 (1): 110272. https://doi.org/10.1016/j.matchar.2020.110272

Kilic, S., (2019). Experimental and Numerical Investigation of the Effect of Different Temperature and Deformation Speeds on Mechanical Properties and Springback Behaviour in Al-Zn-Mg-Cu Alloy. Mechanics, 25 (5): 406-412.
Kilic, S., Kacar, I. & Ozturk, F., (2019). New Trend in Aerospace Industry: Al-Li Based Alloys. Journal of the Faculty of Engineering and Architecture of Gazi University, 34 (1): 275-296.
Kilic, S. & Ozturk, F., (2017). Evaluation of Formability under Different Deformation Modes for Twip900 Steel. Journal of Engineering Materials and Technology, 139 (3): 031001. 10.1115/1.4035621
Kilic, S., Ozturk, F. & Picu, C. R., (2018). Investigation of the Performance of Flow Models for Twip Steel. Journal of materials engineering and performance, 27 (8): 4364-4371. 10.1007/s11665-018-3504-6
Koga, N., Nameki, T., Umezawa, O., Tschan, V. & Weiss, K.-P., (2021). Tensile Properties and Deformation Behavior of Ferrite and Austenite Duplex Stainless Steel at Cryogenic Temperatures. Materials Science and Engineering: A, 801 (1): 140442. https://doi.org/10.1016/j.msea.2020.140442
Kori, P., Vadavadagi, B. H. & Khatirkar, R. K., (2020). Hot Deformation Characteristics of Ass-304 Austenitic Stainless Steel by Tensile Tests. Materials Today: Proceedings, 28 (1): 1895-1898. https://doi.org/10.1016/j.matpr.2020.05.303
Kundu, A., Field, D. P. & Chandra Chakraborti, P., (2020). Effect of Strain and Strain Rate on the Development of Deformation Heterogeneity During Tensile Deformation of a Solution Annealed 304 Ln Austenitic Stainless Steel: An Ebsd Study. Materials Science and Engineering: A, 773 (1): 138854. https://doi.org/10.1016/j.msea.2019.138854
Li, D., Feng, Y., Yin, Z., Shangguan, F., Wang, K., Liu, Q. & Hu, F., (2011). Prediction of Hot Deformation Behaviour of Fe–25mn–3si–3al Twip Steel. Materials Science and Engineering: A, 528 (28): 8084-8089. https://doi.org/10.1016/j.msea.2011.07.073
Li, Q., Ning, J., Chen, L., Hu, J. & Liu, Y., (2020). The Mechanical Response and Microstructural Evolution of 2195 Al–Li Alloy During Hot Tensile Deformation. Journal of Alloys and Compounds, 848 (1): 156515. https://doi.org/10.1016/j.jallcom.2020.156515
Lin, Y. C., Li, K.-K., Li, H.-B., Chen, J., Chen, X.-M. & Wen, D.-X., (2015). New Constitutive Model for High-Temperature Deformation Behavior of Inconel 718 Superalloy. Materials Design, 74 108-118. https://doi.org/10.1016/j.matdes.2015.03.001
Liu, Y., Zhu, B., Wang, Y., Li, S. & Zhang, Y., (2020). Fast Solution Heat Treatment of High Strength Aluminum Alloy Sheets in Radiant Heating Furnace During Hot Stamping. International Journal of Lightweight Materials and Manufacture, 3 (1): 20-25. https://doi.org/10.1016/j.ijlmm.2019.11.004
Lu, J., Song, Y., Hua, L., Zheng, K. & Dai, D., (2018). Thermal Deformation Behavior and Processing Maps of 7075 Aluminum Alloy Sheet Based on Isothermal Uniaxial Tensile Tests. Journal of Alloys and Compounds, 767 (1): 856-869. https://doi.org/10.1016/j.jallcom.2018.07.173
Mao, C., Liu, C., Yu, L., Li, H. & Liu, Y., (2018). Mechanical Properties and Tensile Deformation Behavior of a Reduced Activated Ferritic-Martensitic (Rafm) Steel at Elevated Temperatures. Materials Science and Engineering: A, 725 (1): 283-289. https://doi.org/10.1016/j.msea.2018.03.119
Ozturk, F., Toros, S. & Kilic, S., (2009). Tensile and Spring-Back Behavior of Dp600 Advanced High Strength Steel at Warm Temperatures. Journal of Iron and Steel Research, International, 16 (6): 41-46. https://doi.org/10.1016/S1006-706X(10)60025-8
Ozturk, F., Toros, S. & Kilic, S. , (2010). Tensile Deformation Behavior of Aa5083-H111 at Cold and Warm Temperatures. International Journal of Materials Research, 101 (9): 1172-1179.
Paghandeh, M., Zarei-Hanzaki, A., Abedi, H. R., Vahidshad, Y., Kawałko, J., Dietrich, D. & lampke, T., (2021). Compressive/Tensile Deformation Behavior and the Correlated Microstructure Evolution of Ti–6al–4v Titanium Alloy at Warm Temperatures. Journal of Materials Research and Technology, 10 (1): 1291-1300. https://doi.org/10.1016/j.jmrt.2020.12.110
Pandre, S., Takalkar, P., Kotkunde, N., Kumar Singh, S. & Ul Haq, A., (2019). Influence of Temperatures and Strain Rates on Tensile Deformation Behaviour of Dp 590 Steel. Materials Today: Proceedings, 18 (1): 2603-2610. https://doi.org/10.1016/j.matpr.2019.07.119
Prakash, G., Singh, N. K. & Gupta, N. K., (2020). Deformation Behaviours of Al2014-T6 at Different Strain Rates and Temperatures. Structures, 26 (1): 193-203. https://doi.org/10.1016/j.istruc.2020.03.068
Puchi-Cabrera, E. S., Staia, M. H., Ochoa-Pérez, E., La Barbera-Sosa, J. G., Villalobos-Gutierrez, C. & Brenlla-Caires, A., (2011). Flow Stress and Ductility of Aa7075-T6 Aluminum Alloy at Low Deformation Temperatures. Materials Science and Engineering: A, 528 (3): 895-905. https://doi.org/10.1016/j.msea.2010.11.002
Shimadzu, 2021. Thermostatic Chambe. https://www.shimadzu.com/an/products/materials-testing/uni-ttm-system/tce-n300a/index.html (Erişim Tarihi: 01.07.2021).
Simonetto, E., Bertolini, R., Ghiotti, A. & Bruschi, S., (2020). Mechanical and Microstructural Behaviour of Aa7075 Aluminium Alloy for Sub-Zero Temperature Sheet Stamping Process. International Journal of Mechanical Sciences, 187 105919. https://doi.org/10.1016/j.ijmecsci.2020.105919
Su, M.-N. & Young, B., (2019). Material Properties of Normal and High Strength Aluminium Alloys at Elevated Temperatures. Thin-Walled Structures, 137 (1): 463-471. https://doi.org/10.1016/j.tws.2019.01.012
Tang, K., Zhang, Z., Tian, J., Wu, Y. & Jiang, F., (2021). Hot Deformation Behavior and Microstructural Evolution of Supersaturated Inconel 783 Superalloy. Journal of Alloys and Compounds, 860 (1): 158541. https://doi.org/10.1016/j.jallcom.2020.158541
Toros, S., Kilic, S. & Ozturk, F., (2011). The Effects of Material Thickness and Deformation Speed on Springback Behavior of Dp600 Steel. Advanced Materials Research, 264-265 (1): 636-645. 10.4028/www.scientific.net/AMR.264-265.636
Vilamosa, V., Clausen, A. H., Børvik, T., Holmedal, B. & Hopperstad, O. S., (2016). A Physically-Based Constitutive Model Applied to Aa6082 Aluminium Alloy at Large Strains, High Strain Rates and Elevated Temperatures. Materials Design, 103 (1): 391-405. https://doi.org/10.1016/j.matdes.2016.04.047
Xiao, W., Wang, B., Wu, Y. & Yang, X., (2018). Constitutive Modeling of Flow Behavior and Microstructure Evolution of Aa7075 in Hot Tensile Deformation. Materials Science and Engineering: A, 712 (1): 704-713. https://doi.org/10.1016/j.msea.2017.12.028
Xu, Z., Peng, L., Jain, M. K., Anderson, D. & Carsley, J., (2021). Local and Global Tensile Deformation Behavior of Aa7075 Sheet Material at 673ok and Different Strain Rates. International Journal of Mechanical Sciences, 195 (1): 106241. https://doi.org/10.1016/j.ijmecsci.2020.106241
Yao, K., Min, X., Emura, S. & Tsuchiya, K., (2019). Coupling Effect of Deformation Mode and Temperature on Tensile Properties in Twip Type Ti–Mo Alloy. Materials Science and Engineering: A, 766 (1): 138363. https://doi.org/10.1016/j.msea.2019.138363
Zang, M. C., Niu, H. Z., Zhang, H. R., Tan, H. & Zhang, D. L., (2021). Cryogenic Tensile Properties and Deformation Behavior of a Superhigh Strength Metastable Beta Titanium Alloy Ti–15mo–2al. Materials Science and Engineering: A, 817 (1): 141344. https://doi.org/10.1016/j.msea.2021.141344
Zhang, J.-Y., Jiang, P., Zhu, Z.-l., Chen, Q., Zhou, J. & Meng, Y., (2020). Tensile Properties and Strain Hardening Mechanism of Cr-Mn-Si-Ni Alloyed Ultra-Strength Steel at Different Temperatures and Strain Rates. Journal of Alloys and Compounds, 842 (1): 155856. https://doi.org/10.1016/j.jallcom.2020.155856
Zwick, 2021. Isı Kabinleri. https://www.zwickroell.com/tr/aksesuar/sicaklik-ve-klima/isi-kabinleri/ (Erişim Tarihi: 01.07.2021).

Details

Primary Language

Turkish

Subjects

Mechanical Engineering

Journal Section

Review

Authors

Süleyman Kılıç ^*
0000-0002-1681-9403
Türkiye

Mehmet Fatih Demirdöğen
0000-0002-0545-3733
Türkiye

Publication Date

July 31, 2022

Submission Date

August 27, 2021

Acceptance Date

March 11, 2022

Published in Issue

Year 2022 Volume: 14 Number: 2

DOI

https://doi.org/10.29137/umagd.987547

IZ

https://izlik.org/JA65BU68GK

APA

Kılıç, S., & Demirdöğen, M. F. (2022). Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi. International Journal of Engineering Research and Development, 14(2), 406-419. https://doi.org/10.29137/umagd.987547

AMA

1.Kılıç S, Demirdöğen MF. Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi. IJERAD. 2022;14(2):406-419. doi:10.29137/umagd.987547

Chicago

Kılıç, Süleyman, and Mehmet Fatih Demirdöğen. 2022. “Sıcaklık Ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi”. International Journal of Engineering Research and Development 14 (2): 406-19. https://doi.org/10.29137/umagd.987547.

EndNote

Kılıç S, Demirdöğen MF (July 1, 2022) Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi. International Journal of Engineering Research and Development 14 2 406–419.

IEEE

[1]S. Kılıç and M. F. Demirdöğen, “Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi”, IJERAD, vol. 14, no. 2, pp. 406–419, July 2022, doi: 10.29137/umagd.987547.

ISNAD

Kılıç, Süleyman - Demirdöğen, Mehmet Fatih. “Sıcaklık Ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi”. International Journal of Engineering Research and Development 14/2 (July 1, 2022): 406-419. https://doi.org/10.29137/umagd.987547.

JAMA

1.Kılıç S, Demirdöğen MF. Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi. IJERAD. 2022;14:406–419.

MLA

Kılıç, Süleyman, and Mehmet Fatih Demirdöğen. “Sıcaklık Ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi”. International Journal of Engineering Research and Development, vol. 14, no. 2, July 2022, pp. 406-19, doi:10.29137/umagd.987547.

Vancouver

1.Süleyman Kılıç, Mehmet Fatih Demirdöğen. Sıcaklık ve Deformasyon Hızının Mekanik Özelliklere Etkisinin İncelenmesi. IJERAD. 2022 Jul. 1;14(2):406-19. doi:10.29137/umagd.987547

Cited By

The effect of rolling direction and strain rates on the tensile properties of AA2024-T3 aluminum alloy

European Mechanical Science

https://doi.org/10.26701/ems.1486134

Kırıkkale University, Faculty of Engineering and Natural Science, 71450 Yahşihan / Kırıkkale, Türkiye.

ijerad@kku.edu.tr