Araştırma Makalesi
BibTex RIS Kaynak Göster

Comparative study of some properties of wood plastic composite materials produced with polyethylene, wood flour, and glass flour

Yıl 2023, Cilt: 6 Sayı: 1, 70 - 79, 30.06.2023
https://doi.org/10.33725/mamad.1301384

Öz

Wood flour is the most common filler used in the production of wood plastic composite (WPC) materials. In scientific studies on this subject, wood flours obtained from different trees and fillers obtained from different annual plants are used. In addition, some mineral-based fillers are also used in materials made of plastic. In this study, a low-density polyethylene polymer obtained from recycling was used as the matrix. Larch wood flour and glass flour obtained by grinding soft drink bottles were used as fillers. Composite boards were produced using 60% polymer as the matrix, along with wood flour and glass flour in varying proportions. The density, flexural strength, flexural modulus, tensile strength, tensile modulus, elongation at break, and hardness values of the produced composites were determined. Based on the data obtained, the density increased with the addition of wood flour and glass flour as fillers, and the density-increasing effect of the glass flour was higher than that of the wood flour. Compared to the control samples, it was determined that the bending strength and elongation at break of the experimental groups decreased, and the flexural modulus and tensile modulus increased in the experimental samples using wood flour and glass flour.

Destekleyen Kurum

Kahramanmaraş Sütçü İmam Üniversitesi Bilimsel Araştırma Projeleri Koordinasyon Birimi

Proje Numarası

2022/2-17M

Teşekkür

This work was supported by a grant from the Kahramanmaraş Sütçü İmam University Scientific Research Projects Unit, Project Number: 2022/2-17M. I would like to thank Mr. Ümit Ayata for his contributions to the Shore D hardness tests.

Kaynakça

  • Akbaş, S., Tufan, M., Güleç, T., Taşçıoğlu, C., Peker, H. (2013), Fındık kabuklarının polipropilen esaslı polimer kompozit üretiminde değerlendirilmesi, Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi, 14(1), 50-56.
  • Altuntaş, E., Yılmaz, E., Salan, T. (2017), Yüksek oranda lif dolgu maddesi kullanımının odun plastik kompozit malzemenin mekanik özellikleri üzerine etkisinin araştırılması. Turkish Journal of Forestry, 18(3), 258-263.
  • ASTM D 638 (2022), Standard test method for tensile properties of plastics, ASTM International, West Conshohocken, PA. 1–24 s.
  • ASTM D 790 (2016), Flexural properties of unreinforced and reinforced plastics and electrical insulating materials, ASTM International, West Conshohocken, Philadelphia, PA. 1–9 s.
  • ASTM D 2240 (2021), Standard test method for rubber property-durometer hardness, American Society for Testing and Materials, West Conshohocken, Pennsylvania, United States, 1–27 s.
  • Atar İ., Başboğa, İ. H., Karakuş, K., Mengeloğlu, F. (2016), Utilization of eggplant (Solanum melongena) stalks as a filler ın manufacturıng of compress molded PP based composites. European Journal of Technique (EJT), 6(2), 138-144.
  • Atar İ., Başboğa, İ. H., Karakus, K., Mengeloğlu, F. (2021), Effect of waste tea (Camellia sinensis) wood fibers and mape on some propertıes of high density polyethylene (HDPE) based polymer composites, Turkish Journal of Forest Science, 5(2), 606-619.
  • Ayrilmis, N., Jarusombuti, S. (2011), Flat-pressed wood plastic composite as an alternative to conventional wood-based panels. Journal of composite materials, 45(1), 103-112.
  • Bal B.C. (2022), Lineer düşük yoğunluklu polietilen (LDYPE) ve odun unu ile üretilen kompozit malzemenin bazı mekanik özellikleri üzerine bir araştırma, Mobilya ve Ahşap Malzeme Araştırmaları Dergisi, 5 (1) , 40-49 . DOI: 10.33725/mamad.1126534
  • Bhaskar, K. B., Devaraju, A., Paramasivam, A. (2021), Experimental investigation of glass powder reinforced polymer composite. Materials Today: Proceedings, 39, 484-487.
  • Çavuş, V., Mengeloğlu, F. (2017), The effect of lignocellulosic filler types and concentrations on the mechanical properties of wood plastic composites produced with polypropylene having various melt flowing index (MFI), Pamukkale University Journal of Engineering Sciences, 23(8).
  • Çavuş, V. (2020), Selected properties of mahogany wood flour filled polypropylene composites: the effect of maleic anhydride-grafted polypropylene (MAPP), BioResources, 15(2), 2227-2236.
  • Dundar, T., Ayrilmis, N., Akkus, M., Ulay, G. (2016), Effect of the marble powder and wood powder content on the technological properties of thermoplastic composites. Machines Technologies Materials, 10(6), 13-16.
  • Friedrich, D. (2021), Thermoplastic moulding of Wood-Polymer Composites (WPC): A review on physical and mechanical behaviour under hot-pressing technique, Composite Structures, 262, 113649.
  • Heriyanto, Pahlevani, F., Sahajwalla, V. (2018), Waste glass powder–innovative value-adding resource for hybrid wood-based products, Journal of Cleaner Production, 195, 215-225.
  • Karunanayake, L. (2007), The effects of glass powder on some mechanical properties of engineering thermoplastics, Journal of the National Science Foundation of Sri Lanka, 35(1).
  • Kaymakci, A., Gulec, T., Hosseinihashemi, S. K., Ayrilmis, N. (2017), Physical, mechanical and thermal properties of wood/zeolite/plastic hybrid composites, Maderas Ciencia y tecnología, 19(3), 339-348.
  • Kaymakci, A. (2019), Effect of titanium dioxide on some mechanical, thermal, and surface properties of wood-plastic nanocomposites. BioResources, 14(1), 1969-1979.
  • Kısmet, Y. (2015), Kurutulmuş kolza bitkisinin dolgu malzemesi olarak alçak yoğunluklu polietilenin mekanik özelliklerine, yoğunluğuna ve su emme kapasitesine etkileri, Politeknik Dergisi, 18(4), 203-209.
  • Kristiawan, R. B., Rusdyanto, B., Imaduddin, F., & Ariawan, D. (2022), Glass powder additive on recycled polypropylene filaments: A sustainable material in 3D printing, Polymers, 14(1), 5.
  • Mengeloğlu, F., Karakuş, K. (2008), Some properties of eucalyptus wood flour filled recycled high density polyethylene polymer-composites. Turkish journal of agriculture and forestry, 32(6), 537-546.
  • Mengeloğlu, F., Çavuş, V. (2020), Preparation of Thermoplastic Polyurethane-based Biocomposites through Injection Molding: Effect of the Filler Type and Content, BioResources, 15(3), 5749-5763.
  • Narlıoğlu, N., Çetin, N. S., & Alma, M. H. (2018), Karaçam testere talaşının polipropilen kompozitlerin mekanik özelliklerine etkisi, Mobilya ve Ahşap Malzeme Araştırmaları Dergisi, 1(1), 38-45.
  • Ndiaye, D., Matuana, L. M., Morlat‐Therias, S., Vidal, L., Tidjani, A., Gardette, J. L. (2011), Thermal and mechanical properties of polypropylene/wood‐flour composites, Journal of applied polymer science, 119(6), 3321-3328.
  • Örs, Y., Keskin, H., (2001). Ağaç malzeme bilgisi, Gazi üniversitesi ders kitabı, S:77, Ankara.
  • Sadik, W. A., El-Demerdash, A. G. M., Abokhateeb, A. E., Elessawy, N. A. (2021), Innovative high-density polyethylene/waste glass powder composite with remarkable mechanical, thermal and recyclable properties for technical applications, Heliyon, 7(4), e06627.
  • Stark, N. M., & Matuana, L. M. (2004), Surface chemistry and mechanical property changes of wood‐flour/high‐density‐polyethylene composites after accelerated weathering, Journal of Applied Polymer Science, 94(6), 2263-2273.
  • Tabari, H.Z., Danesh, M.A., Pia, R.H., Nourbakhsh, A., (2011), Evaluation of mechanical and morphological behaviour of polypropylene/wood fiber nanocomposite prepared by melts compounding. In: International Conference on Nanotechnology and Biosensors IPCBEE, vol. 2, pp. 1-4.

Polietilen, odun unu ve cam unu ile üretilen odun plastik kompozit malzemelerin bazı özellikleri üzerine karşılaştırmalı bir çalışma

Yıl 2023, Cilt: 6 Sayı: 1, 70 - 79, 30.06.2023
https://doi.org/10.33725/mamad.1301384

Öz

Odun plastik kompozit (OPK) malzemelerin üretiminde dolgu maddesi olarak çoğunlukla odun unu kullanılmaktadır. Bu konuda yapılan bilimsel çalışmalarda da farklı ağaçlardan elde edilen odun unları ve değişik yıllık bitkilerden elde edilen dolgu maddeleri kullanılmaktadır. Ayrıca, bazı mineral esaslı dolgu maddeleri de plastikten üretilen malzemelerde kullanılmaktadır. Bu çalışmada, geri dönüşümden elde edilen düşük yoğunluklu polietilen polimer matris olarak kullanılmıştır. Dolgu maddesi olarak Karaçam odun unu ve kullanılmış meşrubat şişelerinin öğütülmesi ile elde edilen cam unu kullanılmıştır. Kompozit levhalarda polimer matris %60 oranında ve odun unu ve cam unu ise değişen oranlarda kullanılmıştır. Üretilen kompozitlerin; yoğunluk, eğilme direnci, eğilmede elastikiyet modülü, çekme direnci, çekmede elastikiyet modülü, kopmada uzama ve Shore D sertlik değerleri belirlenmiştir. Elde edilen verilere göre; odun unu ve cam ununun dolgu maddesi olarak eklenmesi ile yoğunluğun arttığı ve cam ununun yoğunluğu artırıcı etkisinin daha fazla olduğu belirlenmiştir. Kontrol örneklerine kıyasla, odun unu ve cam ununun kullanıldığı deney örneklerinde, eğilme direncinin ve kopmada uzama miktarının azaldığı, eğilmede ve çekmede elastikiyet modülünün artığı belirlenmiştir.

Proje Numarası

2022/2-17M

Kaynakça

  • Akbaş, S., Tufan, M., Güleç, T., Taşçıoğlu, C., Peker, H. (2013), Fındık kabuklarının polipropilen esaslı polimer kompozit üretiminde değerlendirilmesi, Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi, 14(1), 50-56.
  • Altuntaş, E., Yılmaz, E., Salan, T. (2017), Yüksek oranda lif dolgu maddesi kullanımının odun plastik kompozit malzemenin mekanik özellikleri üzerine etkisinin araştırılması. Turkish Journal of Forestry, 18(3), 258-263.
  • ASTM D 638 (2022), Standard test method for tensile properties of plastics, ASTM International, West Conshohocken, PA. 1–24 s.
  • ASTM D 790 (2016), Flexural properties of unreinforced and reinforced plastics and electrical insulating materials, ASTM International, West Conshohocken, Philadelphia, PA. 1–9 s.
  • ASTM D 2240 (2021), Standard test method for rubber property-durometer hardness, American Society for Testing and Materials, West Conshohocken, Pennsylvania, United States, 1–27 s.
  • Atar İ., Başboğa, İ. H., Karakuş, K., Mengeloğlu, F. (2016), Utilization of eggplant (Solanum melongena) stalks as a filler ın manufacturıng of compress molded PP based composites. European Journal of Technique (EJT), 6(2), 138-144.
  • Atar İ., Başboğa, İ. H., Karakus, K., Mengeloğlu, F. (2021), Effect of waste tea (Camellia sinensis) wood fibers and mape on some propertıes of high density polyethylene (HDPE) based polymer composites, Turkish Journal of Forest Science, 5(2), 606-619.
  • Ayrilmis, N., Jarusombuti, S. (2011), Flat-pressed wood plastic composite as an alternative to conventional wood-based panels. Journal of composite materials, 45(1), 103-112.
  • Bal B.C. (2022), Lineer düşük yoğunluklu polietilen (LDYPE) ve odun unu ile üretilen kompozit malzemenin bazı mekanik özellikleri üzerine bir araştırma, Mobilya ve Ahşap Malzeme Araştırmaları Dergisi, 5 (1) , 40-49 . DOI: 10.33725/mamad.1126534
  • Bhaskar, K. B., Devaraju, A., Paramasivam, A. (2021), Experimental investigation of glass powder reinforced polymer composite. Materials Today: Proceedings, 39, 484-487.
  • Çavuş, V., Mengeloğlu, F. (2017), The effect of lignocellulosic filler types and concentrations on the mechanical properties of wood plastic composites produced with polypropylene having various melt flowing index (MFI), Pamukkale University Journal of Engineering Sciences, 23(8).
  • Çavuş, V. (2020), Selected properties of mahogany wood flour filled polypropylene composites: the effect of maleic anhydride-grafted polypropylene (MAPP), BioResources, 15(2), 2227-2236.
  • Dundar, T., Ayrilmis, N., Akkus, M., Ulay, G. (2016), Effect of the marble powder and wood powder content on the technological properties of thermoplastic composites. Machines Technologies Materials, 10(6), 13-16.
  • Friedrich, D. (2021), Thermoplastic moulding of Wood-Polymer Composites (WPC): A review on physical and mechanical behaviour under hot-pressing technique, Composite Structures, 262, 113649.
  • Heriyanto, Pahlevani, F., Sahajwalla, V. (2018), Waste glass powder–innovative value-adding resource for hybrid wood-based products, Journal of Cleaner Production, 195, 215-225.
  • Karunanayake, L. (2007), The effects of glass powder on some mechanical properties of engineering thermoplastics, Journal of the National Science Foundation of Sri Lanka, 35(1).
  • Kaymakci, A., Gulec, T., Hosseinihashemi, S. K., Ayrilmis, N. (2017), Physical, mechanical and thermal properties of wood/zeolite/plastic hybrid composites, Maderas Ciencia y tecnología, 19(3), 339-348.
  • Kaymakci, A. (2019), Effect of titanium dioxide on some mechanical, thermal, and surface properties of wood-plastic nanocomposites. BioResources, 14(1), 1969-1979.
  • Kısmet, Y. (2015), Kurutulmuş kolza bitkisinin dolgu malzemesi olarak alçak yoğunluklu polietilenin mekanik özelliklerine, yoğunluğuna ve su emme kapasitesine etkileri, Politeknik Dergisi, 18(4), 203-209.
  • Kristiawan, R. B., Rusdyanto, B., Imaduddin, F., & Ariawan, D. (2022), Glass powder additive on recycled polypropylene filaments: A sustainable material in 3D printing, Polymers, 14(1), 5.
  • Mengeloğlu, F., Karakuş, K. (2008), Some properties of eucalyptus wood flour filled recycled high density polyethylene polymer-composites. Turkish journal of agriculture and forestry, 32(6), 537-546.
  • Mengeloğlu, F., Çavuş, V. (2020), Preparation of Thermoplastic Polyurethane-based Biocomposites through Injection Molding: Effect of the Filler Type and Content, BioResources, 15(3), 5749-5763.
  • Narlıoğlu, N., Çetin, N. S., & Alma, M. H. (2018), Karaçam testere talaşının polipropilen kompozitlerin mekanik özelliklerine etkisi, Mobilya ve Ahşap Malzeme Araştırmaları Dergisi, 1(1), 38-45.
  • Ndiaye, D., Matuana, L. M., Morlat‐Therias, S., Vidal, L., Tidjani, A., Gardette, J. L. (2011), Thermal and mechanical properties of polypropylene/wood‐flour composites, Journal of applied polymer science, 119(6), 3321-3328.
  • Örs, Y., Keskin, H., (2001). Ağaç malzeme bilgisi, Gazi üniversitesi ders kitabı, S:77, Ankara.
  • Sadik, W. A., El-Demerdash, A. G. M., Abokhateeb, A. E., Elessawy, N. A. (2021), Innovative high-density polyethylene/waste glass powder composite with remarkable mechanical, thermal and recyclable properties for technical applications, Heliyon, 7(4), e06627.
  • Stark, N. M., & Matuana, L. M. (2004), Surface chemistry and mechanical property changes of wood‐flour/high‐density‐polyethylene composites after accelerated weathering, Journal of Applied Polymer Science, 94(6), 2263-2273.
  • Tabari, H.Z., Danesh, M.A., Pia, R.H., Nourbakhsh, A., (2011), Evaluation of mechanical and morphological behaviour of polypropylene/wood fiber nanocomposite prepared by melts compounding. In: International Conference on Nanotechnology and Biosensors IPCBEE, vol. 2, pp. 1-4.
Toplam 28 adet kaynakça vardır.

Ayrıntılar

Birincil Dil İngilizce
Konular Kompozit ve Hibrit Malzemeler, Ahşap Esaslı Kompozitler
Bölüm Araştırma Makaleleri
Yazarlar

Bekir Cihad Bal 0000-0001-7097-4132

Proje Numarası 2022/2-17M
Erken Görünüm Tarihi 25 Haziran 2023
Yayımlanma Tarihi 30 Haziran 2023
Gönderilme Tarihi 23 Mayıs 2023
Kabul Tarihi 13 Haziran 2023
Yayımlandığı Sayı Yıl 2023 Cilt: 6 Sayı: 1

Kaynak Göster

APA Bal, B. C. (2023). Comparative study of some properties of wood plastic composite materials produced with polyethylene, wood flour, and glass flour. Mobilya Ve Ahşap Malzeme Araştırmaları Dergisi, 6(1), 70-79. https://doi.org/10.33725/mamad.1301384

Uluslararası Dergidir

32217    18332 18333   3221918334 18335   18336   18339   18434   32216 32218  32220 32221 download download    

32275   32308  32309 


32332