Comparison of Fatigue Analysis Results of Steel Plates Coated with Different Chemical Methods and Samples Joined by Single Lap Joining Method at Different Bonding Thicknesses in Wohler Curves

Year 2024, , 176 - 188, 27.02.2024

Celalettin Baykara

https://doi.org/10.35414/akufemubid.1288047

Abstract

In the second half of18th century As material technology develops day by day within the technological developments that have occurred since the industrial revolution that started, the joining methods of these materials are also being developed. One of these methods is the bonding method in which adhesive chemicals, which have been developed over the last 4 decades, are successfully used. Especially today, as the tendency of automotive companies to reducing the weight of their vehicles increases, the Chemical Joining Method, in which the adhesive element is used as an alternative for the joining of different types and low density materials, is used successfully in almost every industrial sector. In this study, in addition to the natural surface DC01A cold-rolled steel material, which is frequently used in sheet metal coating in the automotive industry, different chemical coating methods such as primer paint and cataphoresis coating were applied, and samples of different thicknesses had been joined with a polyurethane-based adhesive element. The aim of this study is to investigate the thickness and coating method of the adhesive element of two steel materials joined with adhesive to create a strong and flexible bond on the surface. As a research method, fatigue tests were applied to the samples. The results were evaluated by creating Wöhler curves with the Stress (S) and Cycle (N) data obtained as a result of the fatigue tests. As a result of the fatigue test, the cataphoresis coated sample with 3 mm adhesive thickness had infinite life at 0.05 MPA tension, while the other samples failed in the life test. As a result, as a result of the applied tests, it was determined that cataphoresis coated samples with a bonding thickness of up to 3 mm provided better adhesion performance than primer painted samples. Sufficient strength could not be achieved when joining pieces without coating on their surfaces without any coating on the surface were failed

Keywords

Adhesive bonding technique;, Single lap joint, Fatigue analysis;, Cataphoresis coating;, Primer painting

Project Number

KBÜ-BAP-151-DS-041

Farklı Kimyasal Yöntemlerle Kaplanmış Çelik Plakaların Farklı Yapıştırma Kalınlıklarda Tek Bindirmeli Birleştirme Yöntemiyle Birleştirilen Numunelerin Yorulma Analizleri Sonuçlarının Wöhler Eğrilerinde Karşılaştırılması

Abstract

18. yy. ikinci yarısında başlayan endüstri devriminden günümüze kadar yaşanan teknolojik gelişmeler içinde malzeme teknolojisinin günden güne gelişmesiyle bu malzemelerin birleştirme yöntemleri de geliştirilmektedir. Bu yöntemlerden biri de son 40 yıldır gelişme gösteren yapıştırıcı kimyasalların başarıyla kullanıldığı yapıştırma metodudur. Özellikle günümüzde otomotiv firmalarının araçlarının ağırlıklarını hafifleştirilme eğilimi arttığı için farklı türdeki ve düşük yoğunluktaki malzemelerin birleştirilmesinde alternatif olarak yapıştırıcı elemanının kullanıldığı Kimyasal Birleştirme Metodu hemen hemen her sektörde başarıyla kullanılmaktadır. Bu çalışmada, otomotiv sektöründe sac kaplamada sıklıkla kullanılan DC01A soğuk haddelenmiş çelik malzemenin doğal yüzeyine ilaveten astar boya ve kataforez kaplama olarak farklı kimyasal kaplama metotları uygulanmış olup, poliüretan bazlı bir yapıştırıcı elemanıyla farklı kalınlıklarda çelik numuneler birleştirilmiştir. Bu çalışmanın amacı, yapıştırıcı ile birleştirilen iki çelik malzemenin yapıştırıcı elemanın hangi kalınlıkta ve hangi kaplama metodunun yüzeyinde güçlü ve esnek bir bağ oluşturduğunu araştırmaktır. Araştırma metodu olarak numunelere yorulma testleri uygulanmıştır. Yorulma testi sonucunda 3 mm yapıştırıcı kalınlığındaki kataforez kaplı numune 0,05 MPA gerilimde sonsuz ömre sahip olurken, diğer numuneler ömür testinde başarısız olmuştur. Yorulma testleri sonucunda elde edilen Gerilim (S) ve Çevirim (N) verileriyle Wöhler eğrileri oluşturarak sonuçlar değerlendirilmiştir. Sonuç olarak, uygulanan testler sonuçlarında 3 mm.’ye kadar yapıştırma kalınlığında ve kataforez kaplı numuneler, astar boyalı numunelere göre daha iyi yapışma performansı sağlandığı tespit edilmiştir. Yüzeyinde kaplama olmayan numunelerin birleştirilmesinde yeterli dayanım elde edilememiştir.

Keywords

Yapıştırma;, Tek bİndirme Birleştirme Metodu;, Yorulma analizi;, Kataforez kaplama, Astar boya

Supporting Institution

T.C. Karabük Üniversitesi bilimsel araştırma projeleri (BAP) koordinatörlüğü, Hyundai Assan Otomotiv Sanayi A.Ş, Sika Türkiye

Project Number

KBÜ-BAP-151-DS-041

Thanks

Bu çalışma, T.C. Karabük Üniversitesi bilimsel araştırma projeleri (BAP) koordinatörlüğü kapsamında, KBÜ-BAP-151-DS-041 numaralı, hızlı destek projesi olarak desteklenmiştir. Ayrıca, yazar, çelik malzeme tedariğinde Hyundai Assan Otomotiv Sanayi A.Ş’ye, yapıştırıcı tedariğinde Sika Türkiye’ye, ve gözlemlerin bir bölümünde beraber yol aldığı Karabük Üniversitesi Makine Mühendisliği öğrencilerinden Ali Mert İLMENÖZ, Göksel KULA, Kamil AKDOĞAN, Onur ATAMAN’a ve proje onayında katkısı bulunanlara, makalenin olgunlaşmasına katkı koyan hakem ve editörlere, desteklerinden dolayı teşekkür ederim.

References

• Adams, R.D., Comyn, J., Wake, W.C., 1997. Structural Adhesive Joints in Engineering, 2nd ed.; Chapman & Hall: pp. 244–265.
• Al-Moghazy, M., Mahmoud, M., and Nada, A. A. 2020. Fabrication of cellulose-based adhesive composite as an active packaging material to extend the shelf life of cheese. International Journal of Biological Macromolecules, 160, pp.264-275.
• Alsoufi, M. , Bawazeer, T. , Alhazmi, M. and Azam, S., 2017. The Effect of Detergents on the Appearance of Automotive Clearcoat Systems Studied in an Outdoor Weathering Test. Materials Sciences and Applications, 8, 521-536.
• Andaloussi H.A., Mouton, L., Ahmad, A.S., Errotahabere, X., Mougin, S.M., Paboeuf, S., 2022. Fatigue of adhesive bonding: World first fatigue S-N curve for FPSO application. Procedia Structural Integrity, 38, 238–250.
• Bamberg, P. A. M. G. P., Reisgen, U., Schiebahn, A., Barbosa, J. D. V., Marx, B., and Coelho, R. S., 2018. Digital Image Correlation Analysis Of The Effects Of The Overlap Length, Adhesive Thickness And Adherends Yield Strength Over Similar And Dissimilar Joints Of High Strength Steel And Aluminum Alloys. International Journal of Adhesion and Adhesives, 83, 69–75.
• Banea, M. D., Barros, S. de.Budhe, S., Ghumatkar, A., Sekhar, R., 2016. Influence of Adherend Surface Roughness on the Adhesive Bond Strength. Latin American Journal of Solids and Structures, 13(13), 2356–2370.
• Banea, M.D., da Silva, L.F.M., 2009. Adhesively bonded joints in composite materials: an overview. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials Design and Applications, 223 (1), 1-18.
• Baur, P., Casari, P., Choqueuse, D., Davies, P. Roy, A., 2004. Structural mechanical testing of a full-size adhesively bonded motorboat. Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment, 218(4), 259–265.
• Baykara, C., 2023. Effect of single-lap joint different adhesive thickness on fatigue strentgth of metals with different surface coatings. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 237 (17), 1– 18.
• Baykara, C., Teke, I.T, Ertas, A.H, 2023. Effects of the single-lap joint on fatigue strength of metals with different surface coatings: a numerical solution. TransSiberia, 402, 11011.
• Bowen, L., Anand, N., Hossein, A., Soheil, S., 2019. Analyzing effects of surface roughness, voids, and particle-matrix interfacial bonding on the failure response of a heterogeneous adhesive. Computer Methods in Applied Mechanics and Engineering, 346, 410-439.
• Braga D.F.O., De Sousa L.M.C, Infante V., Da Silva L.F.M., Moreira P.M.G.P., 2015. Aluminium friction stir weldbonding. Procedia Engineering, 114, 223–31.
• Budhe, S., Ghumatkar, A., Birajdar, N., Banea, M.D., 2015. Effect of surface roughness using different adherend materials on the adhesive bond strength. Applied Adhesion Science, 3, 1-10.
• Burchardt, B., Dilger, K., Frauenhofer, M., 2018. Handbook of Adhesion Technology, L.F.M. da Silva, A. Ochsner, R.D. Adams (Eds.), second ed., Springer, pp. 1333–1366.
• Clearfield H.M, McNamara D.K, Davis G.D., 1990. Surface preparation of metals. Brinson HF (ed) Handbook on engineered materials: adhesives and sealants, vol 3. ASM International, Metals Park, p 259.
• Davies P, Marine industry, 2018. Hand- book of Adhesion Technology , L.F.M. da Silva, A. Ochsner, R.D. Adams (Eds.), second ed., Springer, pp. 1391–1418.
• Davis, G.D., 2003. Handbook of adhesive technology, Mittal KL, Pizzi A (eds), CRC Press, p. 273.
• Duarte, A.P., Coelho, J.F., Bordado, J.C. , Cidade, M.T. Gil, M.H. , 2012. Surgical adhesives: systematic review of the main types and development forecast. Progress in Polymer Science, 37(8), 1031–1050.
• Ebnesajjad S., 2011. Handbook of adhesives and surface preparation. Sina Ebnesajjad, (ed) William Andrew, p. 259–300.
• Ertas, A. H., Yilmaz, Y. & Baykara, C., 2008. An investigation of the effect of the gap values between the overlap portions of the spot-welded pieces on fatigue life. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 222 (6), 881-890.
• Ferreira, J.A.M., Reis, P.N.B., Costa, J.D.M. and Richardson, M.O.W., 2002. Fatigue Behaviour of Composite Adhesive Lap Joints. Composites Science and Technology, 62(10- 11), 1373–1379.
• Frassetto, A., Breschi, L., Turco, G., Marchesi, G., Di Lenarda, R., Tay, F. R and Cadenaro, M. 2016. Mechanisms of degradation of the hybrid layer in adhesive dentistry and therapeutic agents to improve bond durability—A literature review. Dental Materials, 32(2), e41–e53.
• Ghumatkar, A., Sekhar, R., Budhe, S., 2017. Experimental study on different adherend surface roughness on the adhesive bond strength. Materials Today: Proceedings, 4(8), 7801–7809.
• Golewski, P., Nowicki, M. T., Sadowski, T., Pietras, D., 2021. Bending degradation of thinwalled box beams made of aluminum omega profile and GFRP panel connected by mechanical fasteners. Composite Structure, 282, 115111.
• Goudarzi, R.H., Khedmati, M.R., 2015. An experimental investigation of static load capacity of AL-GFRP adhesively bonded single lap and double butt lap joints. Latin American Journal of Solids and Structures, 12, 183-1594.
• Grätzla, T, Van Dijka , Y., Schrammb, N., et.al., 2019. Influence of the automotive paint shop on mechanical properties of continuous fibre-reinforced thermoplastics. Composite Structures, 208, 557-565.
• Hartz, J. J., Zeig, T., Attin, T., and Wegehaupt, F. J., 2021. Adhesive application before hydrofluoric acid etching during repair procedure in dentistry. International Journal of Adhesion and Adhesives, 111, 102960.
• Ishikawa, H., Seto, K., Shimotuma, S., Kishi, N., & Sato, C. 2005. Bond strength and disbonding behavior of elastomer and emulsion-type dismantlable adhesives used for building materials. International Journal of Adhesion and Adhesives, 25(3), 193–199.
• Jakubinek, M. B., Ashrafi, B., Zhang, Y., Martinez-Rubi, Y., Kingston, C. T., Johnston, A. and Simard, B. 2015. Single-walled carbon nanotube–epoxy composites for structural and conductive aerospace adhesives. Composites Part B: Engineering, 69, 87–93.
• Kaykaç, N.G., 2022. Investigation of Process Parameters on Properties of Epoxy Based Cataphoretic Coatings, (The Degree of Doctor of Philosophy), The Graduate School of Natural and Applied Sciences of Middle East Technical University, 172.
• Kupski, J., Teixeira de Freitas, S., 2021. Design of adhesively bonded lap joints with laminated CFRP adherends: Review, challenges and new opportunities for aerospace structures. Composite Structures, 268, 113923.
• Kwon, Y.T, Kim, Y.S., Lee, Y. , Kwon, S., Lim, M., Lee, Y., Kwon, S., Song, Y.,. Choa, Y.H and Yeo, W.H. , 2018. Ultrahigh conductivity and superior interfacial sdhesion of a nanostructured, photonic-sintered copper membrane for printed flexible hybrid electronics. ACS Applied Materials and Interfaces, 10, 44071–44079.
• Lees, W.A., 1987. Stress Distribution in-Bonded Joints: An Exploration within a Mathematical Model. International Journal of Materials and Product Technology, 2(2), 168–181.
• Maggiore, S., Pedemonte, M., Bazurro, A., Stagnaro, P., Utzeri, R., & Luciano, G., 2020. Characterization of the effect of an epoxy adhesive in hybrid FSW-bonding aluminium-steel joints for naval application. International Journal of Adhesion and Adhesives, 103, 102702.
• Nasresfahani, M.R., Asghari, S., 2023. Review of nondestructive methods for evaluating adhesive bonding on anodized coatings. International Journal of Adhesion and Adhesives, 127, 103491.
• Nonnenman, T, Beygi, R, Carbas, R.J.C, M.D. Banea, da Silva, L.F.M., Öchsner, A, 2022. Synergetic effect of adhesive bonding and welding on fracture load in hybrid joints. Journal of Advanced Joining Processes, 6, 100122.
• Nuhoglu, K., Aktas, E, Tanoglu, M., Martin S.,İplikçi, H., Barışık, M., Yeke, M., Türkdogan, C., Esenoglu, G., Dehneliler, S, İriş M.E., 2023. Analysis of adhesively bonded joints of laser surface treated composite primary components of aircraft structures. International Journal of Adhesion and Adhesives, 126, 103456.
• Nunes, S.L.S., Campilho, R.D.S.G., da Silva, F.J.G., de Sousa, C.C.R.G., Fernandes T.A.B., Banea M.D., da Silva, L.F.M., 2016. Comparative failure assessment of single and double lap joints with varying adhesive system. Journal of Adhesion, 92(7-9), 610-634.
• Paiva, R.M.M. , Marques, E.A.S., da Silva, L.F.M., Antonio, C.A.C., Aran-Ais, F., 2015. Adhesives in the footwear industry. Proceedings of the Institution of Mechanical Engineering, Part L: Journal of Materials: Design and Applications, 203(2), 357–374.
• Paşa, Ç., (2006). Otomotivde boyama teknolojisi ve boya kurutma fırınının ekserji analizi, (Yüksek Lisans Tezi), Yıldız Teknik Üniversitesi Fen Bilimleri Enstitüsü, İstanbul, 131
• Reis, P.N.B., Antunes, F.J.V. and Ferreira, J.A.M., 2005. Influence of Superposition length on Mechanical Resistance of Single-Lap Adhesive Joints. Composite Structures, 67(1), 125–133.
• Reza, A., Shishesaz, M., Tahan, K.N., 2014. The Effect of Viscoelasticity on Creep Behavior of Double-Lap Adhesively Bonded Joints. Latin American Journal of Solids and Structures, 11, 35-50.
• Riesgo, B.V.P., Rodrigues, C.S., Nascimento, L.P, May, L.G, 2023. Effect of hydrofluoric acid concentration and etching time on the adhesive and mechanical behavior of glass-ceramics: A systematic review and meta-analysis. International Journal of Adhesion and Adhesives, 121, 103303.
• Rudawska, A., 2019. Surface Treatment in Bonding Technology; Academic Press Elsevier, pp. 47–59.
• Sadowski, T., Golewski, P. 2014. Effect of Tolerance in the Fitting of Rivets in the Holes of Double Lap Joints Subjected to Uniaxial Tension. Key Engineering Materials, 607, 49–54.
• Sadowski, T., Kneć, M., and Golewski, P., 2014. Fatigue Response of the Hybrid Joints Obtained by Hot Spot Welding and Bonding Techniques. Key Engineering Materials, 601, 25–28.
• Sahin, R., & Akpinar, S., 2021. The effects of adherend thickness on the fatigue strength of adhesively bonded single-lap joints. International Journal of Adhesion and Adhesives, 107, 102845.
• Takeda, T., Yasuoka, T., Hoshi, H., Sugimoto, S., Iwahori, Y., 2019. Effectiveness of Flame-based Surface Treatment for Adhesive Bonding of Carbon Fiber Reinforced Epoxy Matrix Composites. Composites Part A: Applied Science and Manufacturing, 119, 30-37.
• Tan, W., Na, J., Wang, G., Xu, Q., Shen, H., Mu, W., 2021. The effects of service temperature on the fatigue behavior of a polyurethane adhesive joint. International Journal of Adhesion and Adhesives, 107, 102819.
• Tian, F., Jett, K., Flaugher, R., Arora, S., Bergeron, B., Shen, Y., and Tay, F. 2021. Effects of dentine surface cleaning on bonding of a self-etch adhesive to root canal sealer-contaminated dentine. Journal of Dentistry, 112, 103766.
• Traian V. Chirila, 2022. Surgical adhesives based on silk fibroin: A critical account of past and current research. International Journal of Adhesion and Adhesives, 114, 103109.
• TS EN ISO 9664, 1995. Yapıştırıcılar-Çekme kaymasına maruz yapısal yapıştırıcılarda yorulma özellikleri-Deney metotları. TSE, Ankara,17
• Varisli, D., Kaykac, N.G., 2012. COx free Hydrogen Production over Cobalt Incorporated Silicate Structured Mesoporous Catalysts. Applied Catalysis B: Environmental, 127, 389– 398.
• Varisli, D., Kaykac, N.G., 2016. Hydrogen from ammonia over cobalt incorporated silicate structured catalysts prepared using different cobalt salts. International journal of hydrogen energy, 41, 5955-5968.
• Wang, C., Yusufu, D., and Mills, A. 2019. A smart adhesive “consume within” (CW) indicator for food packaging. Food Packaging and Shelf Life, 22, 100395.
• Wang, C.H. and Rose, L. R. F., 2000. Compact Solutions for the Corner Singularity in Bonded Lap Joints. International Journal of Adhesion and Adhesives, 20(2), 145–54.
• Wang, D., Li, Y., Zou, T., Fu, J.,Liu, Z., 2023. Increasing strength and fracture toughness of carbon fibre-reinforced plastic adhesively bonded joints by combining peel-ply and oxygen plasma treatments. Applied Surface Science, 612, 155768.
• Watson, B., Nandwani, Y., Worswick M.J. and Cronin, D.S., 2019. Metallic multi-material adhesive joint testing and modeling for vehicle lightweighting. International Journal of Adhesion and Adhesives, 95, 102421.
• Więckowski, W., Lacki, P., Adamus, J., 2019. Examinations of steel overlap joints obtained using the friction stir welding technology. Archives Metallurgy and Mateials. 64, 393–399.
• Wu, H., Chiang, S. W., Lin, W., Yang, C., Li, Z., Liu, J., Wong, C. P., 2014. Towards Practical Application of Paper based Printed Circuits: Capillarity Effectively Enhances Conductivity of the Thermoplastic Electrically Conductive Adhesives. Scientific Reports, 4(1), 6275.
• Yang, C., Wong, C. P., and Yuen, M. M. F., 2013. Printed electrically conductive composites: conductive filler designs and surface engineering. Journal of Materials Chemistry C, 1(26), 4052.
• Yuya, K., Ikeda, H.; Fujio, Y., Nagamatsu, Y., Shimizu, H., 2020. Surface modification of feldspar porcelain by corona discharge and its effect on bonding to resin cement with silane coupling agent. Journal of the Mechanical Behavior of Biomedical Materials, 105, 103708.
• Zanet, A., Salvo, M, Caselegno, V., 2022. Surface modification of SİC to improve joint strength via Corona plasma treatment. Ceramics International 48, 23492–23497.
• Zhao B, Lu Z-H. A, (2009), Two-dimensional approach of single-lap adhesive bonded joints. Mechanics of Advanced Materials and Structures, 16, 130-159
• https://www.erdemir.com.tr, (04.04.2023)
• https://tur.sika.com, (04.04.2013)
• https://www.labomaronline.com, (05.04.2023)