Research Article
BibTex RIS Cite

Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu

Year 2018, Volume: 18 Issue: 1, 336 - 342, 30.04.2018

Abstract

Bu çalışma bilgisayarlı x-ışını mikro tomografi (μCT) metodunun temel prensiplerine bağlı matematiksel eşitlikler ve metodun metal köpük numunelere uygulanmasını kapsamaktadır. Metalik köpük malzemelerin gözenek yapısının boyut ve dağılım yönünden karakterize edilmesi mekanik, elektrik, ısıl ve korozyon gibi kullanımlarına yönelik özelliklerinin kontrol edilmesi bakımından önemlidir. Bu çalışma laboratuvar koşullarında üretilmiş alüminyum köpüklerin x-ışını mikro tomografi (μCT) tekniği ile analiz ve modelleme uygulamasının irdeleme ve sonuçlarını içermektedir. Mikro-CT tarama işlemi Tübitak Marmara Araştırma Merkezi, Malzeme Enstitüsü’nde gerçekleştirilmiştir. Kabinli x-ışını radyoskopi cihazı olarak YXLON marka Y.MU2000 DCT modeli kullanılmıştır. Tarama işlemi sırasında 200 kV, 4 mA, 1 mm filtre ve 0,4 mm odaklama parametreleri kullanılmıştır. Bu işlem sonrasında 3 farklı metal köpük morfolojisine ait tomografik görüntü ve veriler elde edilmiştir. Elde edilen veriler üzerinden mekanik özellikler sonlu elemanlar yaklaşımı ile analiz edilmiştir.

References

  • Al-Athel, K.S., Aly, S.P., Arif, A.F.M., Mostaghimi, J., 2017. 3D modeling and analysis of the thermo-mechanical behavior of metal foam heat sinks, International Journal of Thermal Sciences, 116, 199-213.
  • Bock, J. and Jacobi, A.M., 2013. Geometric classification of open-cell metal foams using X-ray micro-computed tomography, Materials Characterization, 75, 35-43.
  • Doroszko, M. and Seweryn, A., 2015. Modeling of the tension and compression behavior of sintered 316L using micro computed tomography, Acta Mechanica et Automatica, 9(2), 70-74.
  • Kachelrieß, M., 2008. Micro-CT Molecular Imaging I. Handbook of Experimental Pharmacology. Springer, 23-52.
  • Köll, J., 2015. Modeling of Rigid Foams. Doctoral Thesis, Department of Aeronautical and Vehicle Engineering at KTH Royal Institute of Technology, Stockholm, Sweden, 40.
  • Kowaluk, T., Wozniak, A., 2017. A new threshold selection method for X-ray computed tomography for dimensional metrology, Precision Engineering, 50, 449-454.
  • Larner, M., Acker J., Dávila L.P., 2014. The random porous structure and mechanical response of lightweight aluminum foams, Materials Research Society, 1662(1), 201-210.
  • Li, Y., Xia, X.L., Sun, C., Ai, Q., Liu, B., Tan, H.P., 2018. Tomography-based analysis of apparent directional spectral emissivity of high-porosity nickel foams, International Journal of Heat and Mass Transfer, 118, 2018, 402-415.
  • Luetje, M., Wicke, M., Bacaicoa, I., Brueckner-Foit, A., Geisert, A., Fehlbier, M., 2017. 3D characterization of fatigue damage mechanisms in a cast aluminum alloy using X-ray tomography, International Journal of Fatigue, 103, 363-370.
  • Michailidis, N., Stergioudi, F., Omar, H, Tsipas, D.N., 2009. Investigation of the mechanical behavior of open‐cell Ni foams by experimental and FEM procedures, Advanced Engineering Materials, 10(12), 1122–1126.
  • Miedzinska, D., Szymczyk, W., 2010. Numerical and experimental study of real foam microstructure models, Journal of KONES Powertrain and Transport, 10(2), 309-314.
  • Pérez, L., Lascano, S., Aguilar, C., Domanci, D., 2015. Simplified fractal FEA model for the estimation of the Young’s modulus, Materials Design, 83, 276-283
  • . Wellington, S.L., Vinegar, H.J., 1987. Tomographic imaging of three-phase flow experiments, Review of Scientific Instrumentation, 58(1), 96-107.
  • Yu, J., Lynn, R., Tucker, T., Saldana, K., Kurfess, T., 2017. Model-free subtractive manufacturing from computed tomography data, Manufacturing Letters, 13, 44-47.
Year 2018, Volume: 18 Issue: 1, 336 - 342, 30.04.2018

Abstract

References

  • Al-Athel, K.S., Aly, S.P., Arif, A.F.M., Mostaghimi, J., 2017. 3D modeling and analysis of the thermo-mechanical behavior of metal foam heat sinks, International Journal of Thermal Sciences, 116, 199-213.
  • Bock, J. and Jacobi, A.M., 2013. Geometric classification of open-cell metal foams using X-ray micro-computed tomography, Materials Characterization, 75, 35-43.
  • Doroszko, M. and Seweryn, A., 2015. Modeling of the tension and compression behavior of sintered 316L using micro computed tomography, Acta Mechanica et Automatica, 9(2), 70-74.
  • Kachelrieß, M., 2008. Micro-CT Molecular Imaging I. Handbook of Experimental Pharmacology. Springer, 23-52.
  • Köll, J., 2015. Modeling of Rigid Foams. Doctoral Thesis, Department of Aeronautical and Vehicle Engineering at KTH Royal Institute of Technology, Stockholm, Sweden, 40.
  • Kowaluk, T., Wozniak, A., 2017. A new threshold selection method for X-ray computed tomography for dimensional metrology, Precision Engineering, 50, 449-454.
  • Larner, M., Acker J., Dávila L.P., 2014. The random porous structure and mechanical response of lightweight aluminum foams, Materials Research Society, 1662(1), 201-210.
  • Li, Y., Xia, X.L., Sun, C., Ai, Q., Liu, B., Tan, H.P., 2018. Tomography-based analysis of apparent directional spectral emissivity of high-porosity nickel foams, International Journal of Heat and Mass Transfer, 118, 2018, 402-415.
  • Luetje, M., Wicke, M., Bacaicoa, I., Brueckner-Foit, A., Geisert, A., Fehlbier, M., 2017. 3D characterization of fatigue damage mechanisms in a cast aluminum alloy using X-ray tomography, International Journal of Fatigue, 103, 363-370.
  • Michailidis, N., Stergioudi, F., Omar, H, Tsipas, D.N., 2009. Investigation of the mechanical behavior of open‐cell Ni foams by experimental and FEM procedures, Advanced Engineering Materials, 10(12), 1122–1126.
  • Miedzinska, D., Szymczyk, W., 2010. Numerical and experimental study of real foam microstructure models, Journal of KONES Powertrain and Transport, 10(2), 309-314.
  • Pérez, L., Lascano, S., Aguilar, C., Domanci, D., 2015. Simplified fractal FEA model for the estimation of the Young’s modulus, Materials Design, 83, 276-283
  • . Wellington, S.L., Vinegar, H.J., 1987. Tomographic imaging of three-phase flow experiments, Review of Scientific Instrumentation, 58(1), 96-107.
  • Yu, J., Lynn, R., Tucker, T., Saldana, K., Kurfess, T., 2017. Model-free subtractive manufacturing from computed tomography data, Manufacturing Letters, 13, 44-47.
There are 14 citations in total.

Details

Primary Language Turkish
Journal Section Articles
Authors

Alpay Tamer Ertürk This is me

İsmet Aydın This is me

Publication Date April 30, 2018
Submission Date December 20, 2017
Published in Issue Year 2018 Volume: 18 Issue: 1

Cite

APA Ertürk, A. T., & Aydın, İ. (2018). Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi, 18(1), 336-342.
AMA Ertürk AT, Aydın İ. Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi. April 2018;18(1):336-342.
Chicago Ertürk, Alpay Tamer, and İsmet Aydın. “Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi Ile Yapısal Karakterizasyonu”. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 18, no. 1 (April 2018): 336-42.
EndNote Ertürk AT, Aydın İ (April 1, 2018) Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 18 1 336–342.
IEEE A. T. Ertürk and İ. Aydın, “Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu”, Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi, vol. 18, no. 1, pp. 336–342, 2018.
ISNAD Ertürk, Alpay Tamer - Aydın, İsmet. “Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi Ile Yapısal Karakterizasyonu”. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 18/1 (April 2018), 336-342.
JAMA Ertürk AT, Aydın İ. Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi. 2018;18:336–342.
MLA Ertürk, Alpay Tamer and İsmet Aydın. “Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi Ile Yapısal Karakterizasyonu”. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi, vol. 18, no. 1, 2018, pp. 336-42.
Vancouver Ertürk AT, Aydın İ. Alüminyum Metal Köpüğün Bilgisayar Destekli Mikro-CT Tomografi ile Yapısal Karakterizasyonu. Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi. 2018;18(1):336-42.