Thermo-kinetic modelling of variable valve timing effects on HCCI engine combustion / HCCI Motorun Yanmasına Değişken Supap Zamanlamasının Etkilerinin Termo-Kinetik Modeli

Year 2015, , 54 - 62, 31.01.2015

Mohammadreza Nazemi , Hrishikesh Saigaonkar Mahdi Shahbakhti

https://doi.org/10.18245/ijaet.51525

Cited By: 2

Abstract

In this study the effects of variable valve timing on the combustion of an Homogeneous Charge Compression Ignition (HCCI) engine have been analysed using a new modelling approach for HCCI engine cycle. A novel sequential modelling platform is developed using a combination of detailed multi-zone thermo-kinetic combustion model, 1D intake flow model and exhaust gas flow model. The new model utilizes CHEMKIN-PRO and GT-POWER software along with in-house exhaust gas flow model. Experimental data from a single-cylinder HCCI engine is used to validate the model. Validation results show that the model can predict combustion phasing and Indicated Mean Effective Pressure (IMEP) with average errors of 1.1 crank angle degrees (CAD) and 0.3 bar, respectively. The experimentally validated model is then used to investigate the effects of intake valve timing on HCCI auto-ignition radicals, zonal temperature, combustion phasing, IMEP, and exhaust emissions.

Özet: Bu çalışmada, HCCI motor çevrimi için yeni bir model yaklaşımı kullanılarak, homojen dolgulu sıkıştırma ateşlemeli (HCCI) bir motordaki yanmaya değişken supap zamanlamasının etkisi incelenmiştir. Detaylı bir çok-bölgeli termo-kinetik yanma modeli, 1D emme akış modeli ve egzoz gazı akış modeli kombinasyonu kullanılarak yeni bir ardışık modelleme platformu geliştirilmiştir. Yeni model, yalnızca egzoz manifoldundaki gaz akış modeli ile CHEMKIN-PRO ve GT-POWER yazılımı kullanmaktadır. Modeli doğrulamak için tek silindirli bir HCCI motordan elde edilen deneysel veriler kullanılmıştır. Doğrulama sonuçları göstermiştir ki model, 1.1 krank açısı derecesi ve 0.3 bar ortalama hatalar ile yanma fazını ve ortalama efektif basıncı tahmin edebilmektedir. Deneysel olarak doğrulanan model daha sonra emme supabı zamanının HCCI otomatik ateşleme karakterine, bölgesel sıcaklığa, yanma fazına, ortalama efektif basınca ve egzoz emisyonlarına etkisini araştırmak için kullanılmıştır.

Keywords

Homogeneous Charge Compression Ignition (HCCI), Sequential Model, Multi-Zone, Variable Valve Timing (VVT) / Homojen dolgulu sıkıştırma ateşlemeli (HCCI), Ardışık model, Çoklu bölge, değişken supap zamanlaması (VVT)

References

• H. Zhao, “Homogeneous Charge Compression Ignition (HCCI) and Controlled Auto Ignition (CAI) Engines for the Automotive Industry,” Woodhead Publishing, Brunel University, UK, 2007.
• F. Zhao, T.W. Asmus, D.N. Assanis, J.E. Dec, J.A. Eng, and P.M. Najt, “Homogeneous Charge Compression Ignition (HCCI) Engines: Key Research and Development,” Progress In Technology, Issues PT-94, 2003.
• S. Saxena and I. D. Bedoya, “Fundamental Phenomena Affecting Low Temperature Combustion and HCCI Engines, High Load Limits and Strategies for Extending These Limits,” Progress in Energy and Combustion Science,39(5): 457-488, 2013.
• N. Milovanovic., R. Chen, and J.W.G. Turner. “Influence of The Variable Valve Timing Strategy On The Control Of A Homogeneous Charge Compression (HCCI) Engine,” SAE Technical Paper, 2004-01-1899, 2004.
• N. Milovanovic., D. Blundell, and J. Turner, “Cam Profile Switching (CPS) And Phasing Strategy Vs Fully Variable Valve Train (FVVT) Strategy For Transitions Between Spark Ignition And Controlled Auto Ignition Modes,” SAE Technical Paper, 2005-01-0766, 2005.
• S. M. Aceves, J. R. Smith., C. K. Westbrook, W. J. “Compression Ratio Effect On Methane HCCI Combustion,” Journal of Engineering for Gas Turbines and Power, 121(3): 569-574, 1999.
• D. Law, D. Kemp, J. Allen, G. Kirkpatrick, and T. Copland, “Controlled Combustion In An IC-Engine With A Fully Variable Valve Train,” SAE Technical Paper , 2001-01-0251, 2001.
• P. A. Caton, H. H. Song, N. B. Kaahaaina, and C. F. Edwards. “Residual-Effected Homogeneous Charge Compression Ignition With Delayed Intake-Valve Closing at Elevated Compression Ratio,” International Journal of Engine Research, 6(4): 399-419, 2005.
• L. Koopmans, R. Ogink, and I. Denbratt., “Direct Gasoline Injection in the Negative Valve Overlap of a Homogeneous Charge Compression Ignition Engine,” SAE Transactions, pages 1365-1376, 2003.
• F.Agrell, H. Ångström, B Eriksson, J. Wikander, et al., “Transient Control of HCCI Through Combined Intake and Exhaust Valve Actuation,” SAE Technical Paper 2003-01-3172, 2003.
• E. Hellström, A. G. Stefanopoulou, J. Vavra, A. Babajimopoulos, D. Assanis, L. Jiang and H. Yilmaz, “Understanding the dynamic evolution of cyclic variability at the operating limits of HCCI engines with negative valve overlap,” SAE International Journal of Engines, 2012.
• P. Borgqvist, P. Tunestål and B. Johansson, “Investigation and comparison of residual gas enhanced HCCI using trapping (NVO HCCI) or rebreathing of residual gases,” SAE Technical Paper 2011-01-1772, 2011.
• P. Borgqvist, P. Tunestål, and B. Johansson, “Comparison of negative valve overlap (NVO) and rebreathing valve strategies on a gasoline PPC engine at low load and idle operating conditions,” SAE International Journal of Engines, 2013.
• P. A. Caton, A. J. Simon, J. C. Gerdes, and C. F. Edwards “Residual-effected homogeneous charge compression ignition at a low compression ratio using exhaust reinduction,” International Journal of Engine Research, 2003.
• H.Yun, N.Wermuth and P.Najt, “High load HCCI operation using different valving strategies in a naturally-aspirated gasoline HCCI”. SAE Technical Paper 2011-01-0899, 2011.
• S. M. Aceves, D. L. Flowers, C. K. Westbrook, J. R Smith., W. Pitz, R. Dibble, M. Christensen and B. Johansson, “A multi-zone model for prediction of HCCI combustion and emissions,” SAE Technical Paper 2000-01-0327, 2000.
• M. Shahbakhti and C. R. Koch. “Physics based control oriented model for HCCI combustion timing”. ASME Journal of Dynamic Systems Measurement and Control, Vol. 132, Issue 2, 2010.
• Aceves, S., Flowers, D., Martinez-Frias, J., Smith, J. et al., “A Sequential Fluid-Mechanic Chemical-Kinetic Model of Propane HCCI Combustion,” SAE Technical Paper 2001-01-1027, 2001.
• M. Shahbakhti and C. R. Koch, “Characterizing the cyclic variability of ignition timing in a homogeneous charge compression ignition engine fuelled with n-heptane/iso-octane blend fuels,” International Journal of Engine Research, Vol. 9, Issue 5, pages 361-397, 2008.
• N. P. Komninos, D. T. Hountalas and D. A. Kouremenos, “Description of in-cylinder combustion processes in HCCI engines using a multi-zone model,” SAE Technical Paper 2005-05-0171, 2005.
• H. Seiser, H. Pitsch, K. Seshadri, W. J. Pitz, and H. J. Curran, “Extinction and autoignition of n-heptane in counterflow configuration” Proceedings of the Combustion Institute, 28(2): 2029-2037, 2000.
• G. Woschni, “Universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine” SAE Technical Paper 670931, 1967.
• P. Kirchen, M. Shahbakhti and C. R. Koch, “A skeletal kinetic mechanism for PRF combustion in HCCI engines,” Journal of Combustion Science and Technology, 179(6): 1059 - 1083, 2007.